Inhaltszusammenfassung zur Seite Nr. 1
EXP2800_ENG 7/6/01 4:11 PM Page 11
Inhaltszusammenfassung zur Seite Nr. 2
EXP2800_ENG 7/6/01 4:11 PM Page 1 Introduction The Uniden EXP2800 900 MHz cordless phones are designed and engineered to exacting standards for reliability, long life, and outstanding performance. Features • 900 MHz Extended Range Technology • Page/Find • 10-Number Memory Dialing • AutoTalk™ • 40 Channel Autoscan • AutoStandby™ • Tone/Pulse Dialing • 7 Hours Talk Time • Handset Volume Control • 14 days Standby Time • 32 Digit Redial • Hearing Aid Compatible The EXP2800 features include Auto
Inhaltszusammenfassung zur Seite Nr. 3
EXP2800_ENG 7/6/01 4:11 PM Page 2 4) Place the handset on the base. NOTE: Use only the Uniden Battery (BT-905) supplied with your phone. Replacement batteries are also available through the Uniden Parts Department. Battery use time (per charge) From fully charged • Seven hours continuous use • Fourteen days when the handset is in the standby mode Low Battery Alert When the battery pack is very low and needs to be charged, the phone is programmed to eliminate functions in order to save power.
Inhaltszusammenfassung zur Seite Nr. 4
EXP2800_ENG 7/6/01 4:11 PM Page 3 Included with Your Phone • Base • AC Adapter • Rechargeable Battery • Handset • Telephone Cord Setting up the Phone Do the following steps: A. Choose the best location C. Connect the base unit B. Install the battery pack D. Choose the dialing mode A.Choose the best location Before choosing a location for your new phone, read the INSTALLATION CONSIDERATIONS included in the PRECAUTIONS AND IMPORTANT SAFETY INSTRUCTIONS. Here are some important guidelines you s
Inhaltszusammenfassung zur Seite Nr. 5
EXP2800_ENG 7/6/01 4:11 PM Page 4 After installing the battery pack in the handset, charge your handset at least 15-20 hours before plugging into the phone line. Once the handset battery pack is fully charged, connect the telephone line cord to the base and telephone wall outlet. 5) Connect the telephone line cord to the TEL LINE jack and a telephone outlet once the handset is fully charged. TIP: If your telephone outlet isn’t modular, contact your telephone company for assistance. Modular D.
Inhaltszusammenfassung zur Seite Nr. 6
EXP2800_ENG 7/6/01 4:11 PM Page 5 Terminology Throughout this manual, terms such as Standby and Talk Mode are used. Below is the terminology explanation. • Standby Mode - The handset is not in use, off the base, and talk has not been pressed. A dial tone is not present. • Talk Mode - The handset is off the base and talk has been pressed enabling a dial tone. Adjusting the Ringer and Earpiece Volume Ringer tone and volume When the phone is in standby mode, pressing the volume key on the handse
Inhaltszusammenfassung zur Seite Nr. 7
EXP2800_ENG 7/6/01 4:11 PM Page 6 Page To locate the handset (while it’s off the base), press page/find on the base. The handset beeps for 60 seconds. Paging is canceled when pressing any key, page/find on the base or return the handset to the base. Flash and Call Waiting If you have “call waiting” service and a call waiting tone sounds while you are on a call, press flash to accept the waiting call. There is a short pause, then you will hear the new caller. To return to the original caller,
Inhaltszusammenfassung zur Seite Nr. 8
EXP2800_ENG 7/6/01 4:11 PM Page 7 One-touch priority dialing Your phone is equipped with three “One-touch priority dial” keys for instant dialing. You cannot store phone numbers directly into m1, m2, or m3. They are only used to dial the phone numbers stored into memory locations 1, 2, and 3. (See “Storing a Phone Number in Memory”.) To instantly dial phone numbers stored in memory locations 1, 2, or 3, simply press m1, m2, or m3. (There is no need to press talk. The phone will automatically
Inhaltszusammenfassung zur Seite Nr. 9
EXP2800_ENG 7/6/01 4:11 PM Page 8 Troubleshooting If your EXP2800 cordless telephone is not performing to your expectations, please try these simple steps. NOTE: Do not attempt to service this unit yourself. Servicing must be performed by qualified personnel. Symptom Suggestion The status LED won’t • Make sure the AC adapter is plugged into the base and wall outlet. light when the handset • Make sure the handset is properly seated in the base. is placed in the base. • Make sure that the char
Inhaltszusammenfassung zur Seite Nr. 10
EXP2800_ENG 7/6/01 4:11 PM Page 9 11.To reduce the risk of electric shock, do not disassemble this product. Precautions! Take it to qualified service personnel when service or repair work is Before you read anything else, please observe the following: required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric Warning! shock when the appliance is subsequently used. Uniden America Corporation DOES NOT represent this unit to
Inhaltszusammenfassung zur Seite Nr. 11
EXP2800_ENG 7/6/01 4:11 PM Page 10 If you are having trouble with your telephone service, you must first Applying Power to the Base disconnect your phone to determine if it is the cause of your problem. This phone requires an AC outlet, without a switch to interrupt power, If you determine that it is the cause, you must leave it disconnected and the included AC adapter. To relieve strain on the DC plug when the until the trouble has been corrected. phone is placed on a desk or table, wrap the
Inhaltszusammenfassung zur Seite Nr. 12
EXP2800_ENG 7/6/01 4:11 PM Page 12
