Inhaltszusammenfassung zur Seite Nr. 1
INSTRUCTION MANUAL
CLT-U20
CLT-U30
Dual Handset Models
2.4 GHz
CLT-U12
Cordless Telephone
with Caller ID &
CLT-U22
Visual Call Waiting
CLT-U32
The picture depicts dual handset model
Important
Charge the handset battery for 12 continuous hours prior to first use.
SANYO Canada Inc.
www.sanyocanada.com
1
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS INTRODUCTION -------------------------------------------------------------------- 4 GETTING STARTED ---------------------------------------------------------------- 5 Checking package contents ------------------------------------------------ 5 Modular jack ------------------------------------------------------------------ 5 Installation tips ---------------------------------------------------------------- 5 Battery setup -------------------------------------------------------
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS Handset locator (paging function) ---------------------------------------- 15 MUTE key ---------------------------------------------------------------------15 Low battery warning -------------------------------------------------------15 Voice mail indicator ----------------------------------------------------------16 CALLER ID FEATURES ---------------------------------------------------------- 16 Caller ID with Call Waiting --------------------------------------------------1
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Congratulations on your purchase of this Sanyo cordless telephone. Your Sanyo 2.4 GHz cordless telephone is a fine-quality home communications product. It is carefully designed and produced by a world leader of consumer and industrial electronic equipment. With proper maintenance and care, it will provide you with years of enjoyment and convenience. Main Features 2.4 GHz Technology Superior Range – The use of 2.4 GHz frequency band for signal transmission between base and handset me
Inhaltszusammenfassung zur Seite Nr. 5
GETTING STARTED Checking package contents Make sure your package includes the items shown here. Charger Base unit (For CLT-U12, CLT-U22 & Wall mount CLT-U32) bracket 2 X Handsets (CLT-U20 & CLT-U30 with one handset) 2 X Belt clips 2 X Batteries 2 X AC Adaptors (CLT-U20 & (CLT-U20 & (CLT-U20 & CLT- Battery CLT-U30 with U30 with one U30 with one order sheet one belt clip) battery) adaptor) Telephone KU28-9-250D line cord Modular jack You need an RJ11 type modular phone jack. If you do not have a m
Inhaltszusammenfassung zur Seite Nr. 6
GETTING STARTED Battery setup 1. Remove the battery compartment cover on the handset, insert the battery, plug the cord into the jack (inside the compartment) and replace the cover. 2. Set the handset RINGER switch to ON, and place handset in the base. Slide down the Place the battery Plug the wire Slide up the battery cover in the slot into the jack battery cover Connecting the base unit and charging the handset 1. Plug the AC adaptor into the power DC 9V jack on the back of the base. Plug the
Inhaltszusammenfassung zur Seite Nr. 7
GETTING STARTED Telephone line connection Once the handset battery is fully charged, connect the telephone line cord to the TEL LINE jack on the back of the base. Plug the other end into a telephone outlet. Tone/pulse setting 1. If you have Pulse (rotary) service, you will need to set the dial mode to pulse. If you have Touch-Tone service, do nothing as your phone has been set to Tone prior to shipment. If you do not know which type of service you have, contact your local telephone company. 2.
Inhaltszusammenfassung zur Seite Nr. 8
GETTING STARTED 5. Slip the mounting holes over the wall plate posts and slide the unit down firmly into place. (Wall plate not included.) 6. Place the handset in the base. Note: If desired, gather the extra AC adaptor cord and telephone cord together, fasten with a wire tie, and store inside the wall mounting bracket. Register handsets to the main base before use Your cordless phone uses a digital security system to provide protection against false ringing, unauthorized access and charges to yo
Inhaltszusammenfassung zur Seite Nr. 9
NAMES AND CONTROLS Handset For CLT-U20 & CLT-U30 For CLT-U12, CLT-U22 & CLT-U32 1. Belt clip 11. TALK key (also used to end a call) 2. REDIAL key 12. MUTE/FORMAT key (MUTE/FORMAT/TRANSFER key) 3. Headset jack 13. Ringer switch 4. MEM (memory) key 14. CID/VOL (volume) up/down key 5. CH (channel)/DEL key 15. Keypad (0-9) 6. FLASH/PROG (program) key 16. * TONE/EXIT key 7. Charging contacts 17. # PAUSE key 8. Incoming call/in use LED 18. Microphone 9. Earpiece 10. LCD screen 9
Inhaltszusammenfassung zur Seite Nr. 10
NAMES AND CONTROLS Base Unit Charger (For U12, U22 & U32) 1. Handset cradle 2. PAGE key 3. CHARGE/IN USE LED 4. Wall mount 5. CHARGE LED 10
Inhaltszusammenfassung zur Seite Nr. 11
INITIAL PROGRAMMING Before using this telephone, 4 initial settings must be completed on the handset: Language, Area code (this is required to use Caller ID service from your tele- phone company), Ringer tone, and Tone/Pulse setting. Language setting 1. Make sure the phone is OFF (not in TALK mode). 2. Press FLASH/PROG until “ 1 ENG 2 FRA 3 ESP ” shows on screen. 3. Press CID/VOL or , or the number keys (1 – 3) to select the desired language. 4. Press FLASH/PROG to store selection. Y
Inhaltszusammenfassung zur Seite Nr. 12
INITIAL PROGRAMMING Resetting to default You can reset the phone programming to the initial factory default settings. The default settings are: Language English Area Code - - - Ringer Tone 1 Tone/Pulse Setting Tone 1. Make sure the phone is OFF (not in TALK mode). 2. Press FLASH/PROG repeatedly until “DEFAULT 1 NO” shows on screen. 3. Press CID or , or the 1 or 2 keys to select your choice. 4. Press FLASH/PROG again to confirm. You will hear a confirmation tone. BASICS Receiving a call W
Inhaltszusammenfassung zur Seite Nr. 13
BASICS Making a call 1. Press TALK. Note: If handset is in the base cradle, remove it from base before pressing the TALK key. 2. Dial the phone number. The screen shows the number as you enter it. Telephone Number Volume Level Channel No. Call Timer 3. Press TALK to end your call. Volume adjustment The VOLUME key adjusts the volume level of the earpiece. There are 4 volume levels. 1. Make sure the phone is in TALK mode. 2. Press the CID/VOL or key on the handset. Transfer a call (CLT-U12, CL
Inhaltszusammenfassung zur Seite Nr. 14
BASICS Pre-dialing (up to 32 digits) 1. Make sure the phone is OFF (not in TALK mode). 2. Enter the telephone number. The number is displayed as you enter it. 3. Press TALK. Note: Pressing *TONE will exit pre-dialing. Changing the pre-dial number 1. Make sure the phone is OFF. 2. Enter the telephone number. 3. Press CH/DEL to delete digits one by one. 4. Re-enter the number. Redialing 1. Make sure the phone is OFF. 2. Press TALK. 3. Press REDIAL to redial the last number (up to 32 digits). Fast
Inhaltszusammenfassung zur Seite Nr. 15
BASICS * TONE key This feature enables Pulse service phone users to access touch-tone services offered by banks, credit card companies, etc. 1. Call the bank’s information line. 2. Press *TONE after your call is answered. 3. Follow the voice instructions to complete your transaction. 4. Hang up when finished. The phone returns to Pulse service. Handset locator (Paging function) This feature helps to locate a misplaced handset. 1. Press PAGE on the base, the screen shows “PAGING”. The handset b
Inhaltszusammenfassung zur Seite Nr. 16
BASICS Voice mail indicator When you subscribe to a voice mail service offered by your phone company, the phone alerts you when voice mail has been received. MESSAGE WAITING appears on screen for 60 seconds when a voice mail is received. The LED on the base flashes to indicate there is a voice mail waiting. After the voice mail has been reviewed, MSG WAITING OFF appears on screen, and the indicator stops flashing. Note: The indicator does not work with your answering machine. The phone will o
Inhaltszusammenfassung zur Seite Nr. 17
CALLER ID FEATURES Caller ID list The incoming caller information transmitted from the phone company is received by your phone between the first and second ring and stored in the Caller ID list. If you answer a call before the second ring the caller information may not be stored. When the Caller ID list memory is full, a new call automatically replaces the oldest call in memory. NEW appears on screen for calls received that have not been reviewed. Note: Check with your local phone company regard
Inhaltszusammenfassung zur Seite Nr. 18
CALLER ID FEATURES Storing Caller ID entries in the directory Before storing a caller ID number, make sure the number appears in proper digits for your dialing area. If not, change it using the MUTE/FORMAT key. For example, if the Caller ID number appears 1-416-222-5555 but it is not a long distance number, press MUTE/FORMAT until it shows 416-222-5555 (without 1). Note: If a specific memory entry is longer than 15 digits, the last 15 digits show on the screen. 1. Use the CID/VOL or key to sel
Inhaltszusammenfassung zur Seite Nr. 19
CALLER ID FEATURES Deleting all entries 1. Make sure the phone is OFF (not in TALK mode). 2. Use the CID/VOL or keys to display any entry. 3. Press and hold CH/DEL, until “DELETE ALL?” shows on screen. 4. Press CH/DEL again to confirm. “NO CALLS” shows on screen. DIRECTORY You can store up to 10 names (up to 15 characters) and numbers (up to 24 digits) in the directory for quick dialing. If a number exceeds 24 digits, you can program it in parts, and then chain dial the number. Store a numbe
Inhaltszusammenfassung zur Seite Nr. 20
DIRECTORY 7. Use the digit keys to enter the desired telephone number. If you make a mistake, press CH/DEL to delete previous digits one by one, then enter the correct digits. If you wish to add a pause, press PAUSE two times at the desired location. Be sure to press it twice, or you will enter a # (number sign) and not a pause. Each pause counts as 1 digit in the dialing sequence. Or you can store redial number in the directory by pressing REDIAL (Note: If the redial number is longer than 24 d