Inhaltszusammenfassung zur Seite Nr. 1
Installation Instructions
Distinctive Series Cooktop
Models: DRT304S, DRT366S
THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST
EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS APPLIANCES.
Part No. 106522 Rev. B
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Important Safety Instructions .......................................... 1 Installation Instructions .................................................... 7 Important Information About Safety Instructions .............. 1 Cooktop Installation .......................................................... 7 General Safety Precautions ............................................. 2 Gas Line Connection ....................................................... 8 Installation Requirements
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Instructions Important Information About DANGER IMPORTANT: If you smell gas: Safety Instructions • Do not use or light any appliance. • The Important Safety Instructions and warnings in this manual are not meant to cover all possible prob- • Do not touch any electrical switch or use any electri- lems and conditions that can occur. Use common cal devices, including the telephone, in your building. sense and caution when installing, maintaining or oper- • From a neighbor’s
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau- tions, including the following: WARNING WARNING • Read the accompanying use and care manual com- • Do not climb on any part of the appliance. pletely before operating this appliance. • To avoid a fire hazard, do not hang flammable or • Keep packaging materials away from children. heat sensitive objects over the
Inhaltszusammenfassung zur Seite Nr. 5
Installation Requirements Gas Supply Requirements WARNING • Observe all governing codes and ordinances during • Check your local building codes for the proper method planning and installation. Contact your local building of installation. In the absence of local codes, this department for further information. appliance should be installed in accordance with the National Fuel Gas Code ANSI Z223.1/NFPA 54. The • To prevent an electric shock hazard, the power sup- gas service must be inst
Inhaltszusammenfassung zur Seite Nr. 6
Installation Requirements • To reduce the risk of personal injury and to reduce Cabinet and Countertop Layout accumulated smoke in the room, Dacor strongly recom- mends installing a range hood. A hood should project forward a minimum of five (5) inches beyond the face WARNING of the cabinets. To avoid the risk of fire or personal injury, all minimum • The installation must allow access to the underside and maximum specified clearances on this and the of the cooktop for service and insp
Inhaltszusammenfassung zur Seite Nr. 7
Installation Requirements Cabinet tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted. Cabinet/Cutout Dimensions 1 1/2” (38 mm) 10” (254 mm) to typical countertop combustible side thickness wall Min. both sides 1/2” (13 mm) overhang, both sides B 7 3/4” (197 mm) Recommended Cooktop platform gas and electrical 36” (914 mm) 1” (25 mm) Min. service location, typical thickness consult local code Cabinet/Countertop Dimensions - Front View 13” (330 mm) 3 max. C Cooktop B C Model 30” (762 mm)
Inhaltszusammenfassung zur Seite Nr. 8
Countertop Installation Requirements Cabinet/Countertop Dimensions (cont.) Cutout tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted. Gas and electrical connections at right rear section of chassis Gas connection and power cord may be routed through bottom or back of chassis Increase countertop and overhang additional 2 1/2” (64 mm) Min. for Non-combustible combustible rear wall above rear wall, rear of countertop mounting platform 10” (254 mm) min. to combustible wall 3/8” (13
Inhaltszusammenfassung zur Seite Nr. 9
Installation Instructions Unpack the Cooktop Cooktop Installation WARNING WARNING • If the gas and electric service provided does not • To prevent damage to the gas pressure regulator, meet the product specifications, do not proceed with install it only after the cooktop is mounted in its per- the installation. Call the dealer, the gas supplier or a manent position. licensed electrician. • Do not over-tighten the hold down bolts. Over tight- • The cooktop is heavy. A minimum of two peo
Inhaltszusammenfassung zur Seite Nr. 10
Installation Instructions Knob Installation Control Panel - 1. Attach the SimmerSear burner knobs A as shown DRT304S below. The SimmerSear knobs have a wider space between the large flame icon and the simmer icon than the standard burner knobs. Align the “D-shaped” open- B ing on the back of each knob with the end of the valve shaft. Carefully push each knob on until it stops. A B 2. Attach the remaining knobs which operate the standard burners B . B Control Panel - A
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions Burner Component Installation WARNING • Never attempt to operate the cooktop with any of the burner parts removed. • Do not attempt to adjust the burner air mixture settings. All adjustments are preset at the factory. Remove the burner parts and grates from their shipping packages. SimmerSear Burner Assembly Standard Burner Assembly 1. Install the SimmerSear burner ring(s) on top of the 1. Install the standard burner rings on the standard burner SimmerSear burner ba
Inhaltszusammenfassung zur Seite Nr. 12
Installation Instructions NOTE: If the cooktop does not operate properly, follow Verifying Proper Operation these troubleshooting steps: • Verify that power and gas are supplied to the cooktop. WARNING • Check to make sure that the power plug is connected • Make sure that power to the electrical outlet is turned to the electrical outlet and that power is turned on at off at the circuit breaker or fuse box and that the gas the circuit breaker or fuse box. is turned off at the gas supply
Inhaltszusammenfassung zur Seite Nr. 13
WIRING DIAGRAM 120V, 60Hz, 0.25A DRT304 POWER SUPPLY VERIFY PROPER OPERATION G AFTER SERVICING RL INDICATOR LIGHT RR INDICATOR LIGHT W B W B W B W RL RR IGNITOR IGNITOR RL O RR W O W RR Single Point Single Point Spark Module B B B Spark Module S1 RL B B S2 FL INDICATOR LIGHT FR INDICATOR LIGHT W B W B FL FR IGNITOR IGNITOR O FR O FL W W Single Point Single Point FR Spark Module Spark Module B B B S3 FL B B S4 Wiring Diagrams 11
Inhaltszusammenfassung zur Seite Nr. 14
Wiring Diagrams 12 WIRING DIAGRAM 120V, 60Hz, 0.25A DRT366 POWER SUPPLY VERIFY PROPER OPERATION AFTER SERVICING G RR RL INDICATOR LIGHT RC INDICATOR LIGHT B W INDICATOR LIGHT W B W B W B W RR RL IGNITOR RC IGNITOR IGNITOR O W W O W RR O RL RC RR Single Point Single Point B Single Point B S1 B B Spark Module Spark Module Spark Module RC B B S2 B RL B FR S3 FL INDICATOR LIGHT FC INDICATOR LIGHT INDICATOR LIGHT W B B W B W FR FC IGNITOR IGNITOR O O W FL W O FC FR W FR Single Point Single Point Si
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
