ملخص المحتوى في الصفحة رقم 1
Contents
1 INSTRUCTIONS FOR SAFE AND PROPER USE ______________________ 4
2 POSITIONING OF THE HOB ______________________________________ 6
3 ELECTRICAL CONNECTION______________________________________ 7
4 GAS CONNECTION _____________________________________________ 8
5 ADJUSTMENT FOR DIFFERENT TYPES OF GAS ____________________ 10
6 FINAL OPERATIONS ___________________________________________ 14
7 USING THE HOB ______________________________________________ 16
8 CLEANING AND MAINTEN
ملخص المحتوى في الصفحة رقم 2
Introduction 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SERIES OF NOZZLES SUPPLIED. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED
ملخص المحتوى في الصفحة رقم 3
Introduction THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE HOB. DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE COOKING HOB GRIDS. DO NOT USE PANS OR GRIDDLE PLATES THAT EXTEND BEYOND THE EXTERNAL PERIMETER OF
ملخص المحتوى في الصفحة رقم 4
Instructions for the installer 2 POSITIONING OF THE HOB The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 2.1 Attachment to support structure Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a
ملخص المحتوى في الصفحة رقم 5
Instructions for the installer 3 ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations. Check that the power line is adequately grounded. On the power line, install an omnipolar cut-off device with c
ملخص المحتوى في الصفحة رقم 6
Instructions for the installer 4 GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the provisions defined by standard regulations in force. To facilitate connection, fitting A on the rear of the appliance may be adjusted laterally. For this purpose, undo the hexagonal nut B, turn the union A into the position required and retighten the hexagonal nut B to a torque of at least 20 Nm. An annealed aluminium ga
ملخص المحتوى في الصفحة رقم 7
Instructions for the installer 4.1 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standards regulations in force. Make sure that feed pressure conforms to the levels shown in the table in paragraph “5.2 Regulation for LPG”. 4.2 Ventilation of rooms The hob may be installed only in rooms with permanent ventilation, as required by standards regulations in force. The room in which the hob is installed must have su
ملخص المحتوى في الصفحة رقم 8
Instructions for the installer 5 ADJUSTMENT FOR DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, disconnect the appliance from the electrical socket. A label on the bottom enclosure of the hob declares for which type of gas the appliance has been adjusted. For functioning with other types of gas the nozzles must be replaced and the primary air adjusted. To replace the nozzles and regulate the burners, operate as described in the following paragraph
ملخص المحتوى في الصفحة رقم 9
Instructions for the installer 5.2 Nozzle replacement and primary air adjustment Loosen screw A and push support B all the way. Use a double head wrench to remove nozzle C and assemble the suitable one, following the values indicated in the tables relevant to the type of gas to use. The screwing torque of the nozzle should never exceed 3 Nm. Reposition support B so that nozzle C is covered perfectly. Move the Venturi tube D to regulate the air flow until distance “X” is reached in
ملخص المحتوى في الصفحة رقم 10
Instructions for the installer Rated Burner heating Natural gas – G20 2.0 kPa capacity Nozzle diameter Reduced flowrate 1/100 mm (W) Auxiliary 1.05 73 380 Semirapid 1.65 92 380 Rapid 2.55 115 750 Rapid large 3.1 126 800 Fish pan 1.8 95 100 Ultra rapid 3.3 130 1400 Internal 0.8 67 380 Double crown External 3.3 130 900 12
ملخص المحتوى في الصفحة رقم 11
Instructions for the installer Rated Burner heating Town gas G110 – 0.8 kPa capacity Nozzle diameter Reduced flowrate 1/100 mm (W) Auxiliary 1.05 132 380 Semirapid 1.65 165 380 Rapid 2.55 210 600 Rapid large 3.1 240 800 Fish pan 1.8 177 750 Ultra rapid 3.3 250 900 Internal 0.8 115 380 Double crown External 3.3 250 900 Regulation of primary air Referred to distance “X” in mm. G20 G30/G31 G110 Burner 2.0 kPa 2
ملخص المحتوى في الصفحة رقم 12
Instructions for the installer 6 FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph “5.1 Removing the hob”. 6.1 Regulation of turndown rate for natural gas or town gas Replace the components on the burner and slide the knobs on the gas tap pins. Light the burner and set it at turndown rate position. Remove the knob and turn the regulation screw inside or next to the gas tap pin (depen
ملخص المحتوى في الصفحة رقم 13
Instructions for the installer 6.3 Arrangement of the burners on the hob Burners 1. Auxiliary 2. Semi rapid 3. Rapid 4. Rapid large 5. Ultra rapid 6. Double crown 7. Fish pan 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned inside and re-greased. This must be done by a qualified technician. 15
ملخص المحتوى في الصفحة رقم 14
Instructions for the user 7USINGTHEHOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B. Grid C provided is intended for use with woks (Chinese pans). Adapter D comes only with open grids models and is intended for use with small sized vessels. 7.1 Ignition of the burners The device is fit with electronic ignition. Simply press and simul
ملخص المحتوى في الصفحة رقم 15
Instructions for the user 7.2 Practical advice for using the burners For better burner performance and minimum gas consumption, flat bottomed, even pans must be used, with covers and proportional in size to the burners (see paragraph “7.3 Diameter of the pans”). To avoid overcooking or damage to the surface top while cooking, all pans or griddles must be positioned within the cooking hob perimeter and must be a minimum distance of 3-4 cm from the knobs. 7.3 Diame
ملخص المحتوى في الصفحة رقم 16
Instructions for the user 8 CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the appliance. 8.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the surface, always use specific products only, which do not contain abrasive substances or chlorine-based acid substances. How to use: pour the product on a damp clo
ملخص المحتوى في الصفحة رقم 17
Instructions for the user 8.2.2 The cover Clean the glass or steel cover, where mounted, with warm water. Never use abrasive sponges or detergents. Attention: the glass lid may break if overheated. Make sure that all the burners are switched off and let them cool down before lovering the lid. 19
ملخص المحتوى في الصفحة رقم 18
Cod. 914772070/B
