ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
Installation Instructions BEFORE YOU BEGIN CAUTION: THESE COOKTOPS SHOULD BE INSTALLED Read these instructions completely and IN CONJUNCTION WITH A SUITABLE carefully. OVERHEAD VENT HOOD. Due to the high heat capacity • IMPORTANT – Save these instructions for of this unit, particular attention should be paid to the local inspector’s use. hood and duct work installation to assure it meets local building codes. • IMPORTANT – Observe all governing codes and ordinances. MISE EN GARDE : • Note to
ملخص المحتوى في الصفحة رقم 3
Design Information CONTENTS Installation Instructions Design Information Step 1, Remove Packaging ..............................................7 Models Available ..............................................................3 Step 2, Cut the Countertop Opening ..............................7 Accessory Requirements ................................................3 Step 3, Install the Cooktop ..............................................8 Product Dimensions and Clearances .......................
ملخص المحتوى في الصفحة رقم 4
ملخص المحتوى في الصفحة رقم 5
Installation Preparation INSTALLATION OPTIONS ADVANCE PLANNING These cooktops can be installed in standard 24" or Refer to “Dimensions and Clearances” for appropriate deeper 25" cabinets. placement and necessary clearances when planning the installation. • In 24" deep cabinets, the front of the cooktop will project approximately 1-7/8" beyond the front of the • Cabinetry cannot be installed directly above the countertop. cooktop. • In 25" deep cabinets, the cooktop will be flush with • We recom
ملخص المحتوى في الصفحة رقم 6
Installation Preparation TOOLS REQUIRED MATERIALS REQUIRED (not supplied) • Saw • Pipe and fittings as required • Measuring tape • Manual gas line shut-off valve • Carpenter’s square • Gas pressure regulator (supplied) • Large flat-blade screwdriver • Gas-resistant pipe joint sealant • Pipe wrench • 5 foot, 5/8" AGA-certified flexible metal gas supply line (length must comply with local codes) – If required by local codes, use solid pipe fittings. NOTE: Purchase new flexible line. DO NOT USE OL
ملخص المحتوى في الصفحة رقم 7
ملخص المحتوى في الصفحة رقم 8
Installation STEP 3 INSTALL COOKTOP • Lower the cooktop into the opening. Make sure the cooktop is evenly seated and supported. A side frame gasket will seal the cooktop to the countertop. • “L” brackets with screws are provided to secure the cooktop to the countertop or to adjacent cabinetry. Alternate Bracket – Alternate screw hole locations on the sides of the Screw Holes cooktop allow for varying thicknesses of countertops or side cleats. • Select the bracket location; secure the bracket to
ملخص المحتوى في الصفحة رقم 9
Installation STEP 5 CONNECT ELECTRICAL Plug power cord into properly grounded receptacle. STEP 6 ASSEMBLE BURNERS, CHECK IGNITION Assemble burners as shown. Check to be sure that burner heads and caps are securely seated. Pin(s) must Burner Cap completely engage holes to ensure proper assembly. Burner Head • Check for proper ignition: (Brass) – Push in one control knob and turn 90° to Lite position. Locator Pins – The igniter will spark and the burner will light; the Burner Ring igniter will ce
ملخص المحتوى في الصفحة رقم 10
Installation FINALIZE INSTALLATION Place the burner grates over the burners. Press corner The griddle has two leveling screws beneath the rear of the grate to the cooktop. The grates should be seated flue cover that can be used to adjust to the desired slope. and should not rock. The center screw is for shipping purposes only and can be removed. The grill and griddle are secured with screws at the front. They are designed to be stationary and should not be removed. INSTALLATION CHECKLIST ❑ Doubl
ملخص المحتوى في الصفحة رقم 11
ملخص المحتوى في الصفحة رقم 12
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-80225-2 Part No. 164D4290P377 17713 Rev. 2 10-04 JR
