ملخص المحتوى في الصفحة رقم 1
Installation
Above the
Instructions Cooktop Oven
JVM1790
Questions? Call 1-800-361-3400 or Visit our Website at: geappliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• Note to Consumer – Keep these
instructions for future reference.
•
IMPORTANT – Save these
• Skill level – Installation of this appliance requires
instructions for local inspector’s use.
basic mechanical and electrical skills.
•
IMPORTANT – Observe all • Proper installation is the responsibility of t
ملخص المحتوى في الصفحة رقم 2
Installation Instructions Recirculating ........................................ 19–22 C CONTENTS Attach Mounting Plate to Wall ............19 General information Preparation of Top Cabinet ................19 Important Safety Instructions .................................. 3 Adapting Blower Electrical Requirements .......................................... 3 for Recirculation ..........................20, 21 Hood Exhaust ...................................................... 4, 5 Mount the Oven
ملخص المحتوى في الصفحة رقم 3
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit checked The installer must perform a ground continuity check by a qualified electrician to make sure the receptacle is on the power outlet box before beginning the properly grounded. installation to insure that the outlet box is properly Where a standard two-prong wall receptacle is grounded. If not properly grounded, or if the outlet enco
ملخص المحتوى في الصفحة رقم 4
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6”/15.2
ملخص المحتوى في الصفحة رقم 5
Installation Instructions NOTE: If you need to install ducts, note that the total Maximum duct length: 1 duct length of 3 ⁄4” x 10” (8.2 x 25.4 cm) rectangular or For satisfactory air movement, the total duct length of 6” (15.2 cm) diameter round duct should not exceed 1 3 ⁄4” x 10” (8.2 x 25.4 cm) rectangular or 6” (15.2 cm) 140 equivalent feet (42.7 m). diameter round duct should not exceed 140 equivalent Outside ventilation requires a HOOD EXHAUST DUCT. feet (42.7 m). Read the following ca
ملخص المحتوى في الصفحة رقم 6
INSTALLATION INSTRUCTIONS Installation Instructions PARTS INCLUDED DAMAGE—SHIPMENT/ INSTALLATION ADDITIONAL PARTS • If the unit is damaged in shipment, return the PART QUANTITY unit to the store in which it was bought for repair or replacement. Top Cabinet 1 TOP CABINET TEMPLATE Template • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must Rear Wa
ملخص المحتوى في الصفحة رقم 7
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square #1 and #2 Phillips screwdriver (optional) Tin snips (for cutting damper, if required) Scissors 3 7 Electric drill with ⁄16“, ⁄16“ (to cut template, if necessary) 1 5 ⁄2“ and ⁄8“ drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (optional) Duct
ملخص المحتوى في الصفحة رقم 8
Installation Instructions PLACEMENT OF THE MOUNTING PLATE 1 A. REMOVING THE OVEN FROM B . FINDING THE WALL STUDS THE CARTON/REMOVING THE MOUNTING PLATE 1 Remove the box containing the installation instructions, filters, exhaust adaptor, damper and the small hardware bag. Do not remove the Wall Styrofoam protecting the front of the oven. Studs 2 Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in C
ملخص المحتوى في الصفحة رقم 9
At least 30 ″ (76.2 cm), up to 36 ″ (91.4 cm) Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Plate position—beneath framed recessed Plate position—beneath flat bottom cabinet bottom cabinet Mounting Plate Tabs Mounting Plate Tabs Touching the Back Frame Touching the Cabinet Bottom 30″ (76.2 cm) to Cooktop Plate position—beneath recessed bottom Your cabinets may have decorative trim that cabinet with front overhang interferes with the oven installation. Rem
ملخص المحتوى في الصفحة رقم 10
Installation Instructions D. ALIGNING THE WALL PLATE Hole B Hole A Draw a Vertical Line on Wall from Center of Top Cabinet Hole C Hole D CAUTION: Wear gloves Area E to avoid cutting fingers on sharp edges. NOTE: Holes C and D are inside area E. If neither 1 Draw a vertical line on the wall at the center of the C nor D is in a stud, find a stud somewhere in area E 30 ″ (76.2 cm) wide space. and draw a fifth circle to line up with the stud. It is 2 Use the mounting plate as the template for the
ملخص المحتوى في الصفحة رقم 11
Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This oven is designed for adaptation to the following NOTE: This oven is shipped assembled for Outside Top 3 types of ventilation: Exhaust. Select the type of ventilation required for your installation and proceed to that section. A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C.Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST A B (VERTICAL DUCT) (HORIZONTAL DUCT) Adap
ملخص المحتوى في الصفحة رقم 12
Installation Instructions OUTSIDE TOP EXHAUST (Vertical Duct) A INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Adapter A4. Mount Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork To use toggle bolts: A1. ATTACH THE MOUNTING Spacing for Toggles PLATE TO THE WALL More Than Wall Thickness Toggle Wings Mounting Toggle Plate Bolt Wall Bolt End 3 Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount t
ملخص المحتوى في الصفحة رقم 13
Installation Instructions A2. USE TOP CABINET TEMPLATE A4. MOUNT THE OVEN FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to
ملخص المحتوى في الصفحة رقم 14
Installation Instructions A4. MOUNT THE OVEN (continued) A5. ADJUST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor Cabinet Front to connect to the house duct. Cabinet Bottom Shelf Filler Block Damper Equivalent to Depth of Cabinet Recess Back of oven Self-Aligning Screw Oven Top 4 Attach the oven to the top cabinet. Insert 2 self-aligning screws 5 1 1 ( ⁄4”-28 x 3 ⁄4”) through outer top cabinet holes. Turn two A6. CONNECTING DUCTWORK full turns on each screw. House Du
ملخص المحتوى في الصفحة رقم 15
Installation Instructions OUTSIDE BACK EXHAUST (Horizontal Duct) B INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Mounting Plate to Wall B3. Prepare Top Cabinet B4. Adjust Blower B5. Mount the Oven ATTACH THE MOUNTING PREPARING THE REAR WALL B2. B1. PLATE TO THE WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1 Remove t
ملخص المحتوى في الصفحة رقم 16
Installation Instructions To use toggle bolts: B4. ADAPTING BLOWER FOR Spacing for Toggles More OUTSIDE BACK EXHAUST Than Wall Thickness Remove the three screws that hold the blower 1 Toggle Wings plate to the oven. Slide blower plate from under Mounting Toggle its retaining flange. Remove and save the screw Plate Bolt that holds blower motor to oven. Retaining Flange Blower Plate Wall Bolt End Blower Motor Place the mounting plate against the wall and 3 Screw insert the toggle wings into the
ملخص المحتوى في الصفحة رقم 17
Installation Instructions 5 Roll the blower unit 90° so that fan blade 8 Replace the blower plate in the same position openings are facing out the back of the oven. as before with the screws. Blower Plate Screws Before Rolling After Rolling Blower Plate Back of Oven 9 Insert the tabs on each side of the damper into the holes at the inside rear of the adaptor. Back of Back of Oven Oven Locate the two “knockout” plates, on the rear 6 oven panel, near the top of the oven. Using tin snips, carefull
ملخص المحتوى في الصفحة رقم 18
Installation Instructions Cabinet Front B5. MOUNT THE MICROWAVE Cabinet Bottom Shelf OVEN Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL Oven Top SAFETY, WE RECOMMEND THAT TWO PEOPLE 4 Attach the oven to the top cabinet. INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle 5 Insert 2 self-aligning screws during installation. 1 1 ( ⁄4”-28 x 3 ⁄4”) through outer NOTE: If your cabinet is metal, use the nylon top cabinet ho
ملخص المحتوى في الصفحة رقم 19
Installation Instructions RECIRCULATING (Non-Vented Ductless) C INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter (not supplied) 3 Place the mounting plate against the wall and C1. ATTACH THE MOUNTING insert the toggle wings into the holes in the wall to mount the plate. PLATE TO THE WALL NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of
ملخص المحتوى في الصفحة رقم 20
Installation Instructions C3. ADAPTING BLOWER Carefully pull out the blower unit. The wires 3 will extend far enough to allow you to adjust the FOR RECIRCULATION blower unit. NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. Remove and save screws that hold blower plate to 1 the oven. Blower Plate Screws Roll the blower unit 90° so that fan blade openings 4 are facing toward the front of the oven. Back of Oven BEFOR
