ملخص المحتوى في الصفحة رقم 1
NEC-ADA201 Eng/Fr. manual 9/8/98 12:25 PM Page 1
®
®
MultiSync
MultiSync
™
™
IntelliBase
IntelliBase
Audio
Audio
User’s Manual
User’s Manual
ملخص المحتوى في الصفحة رقم 2
NEC-ADA201 Eng/Fr. manual 9/8/98 12:25 PM Page 2 Index Contents 1 Quick Start 2–11 Controls 12 Specifications 13 Troubleshooting 14 References 15 Limited Warranty 16 Table des matières Contenu 19 Démarrage rapide 20–29 Commandes 30 Caractéristiques 31 Dépannage 32 Références 33 Garantie Limitée 34
ملخص المحتوى في الصفحة رقم 3
NEC-ADA201 Eng/Fr. manual 9/8/98 12:25 PM Page 3 Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC INTELLIBASE AUDIO: Read Instructions — All the safety and operating instructions should be read before the appliance is operated. Retain Instructions — The operating instructions should be retained for future reference. Heed Warning — All warnings on the appliance and in the operating instructions should be adhered to.
ملخص المحتوى في الصفحة رقم 4
NEC MultiSync Monitors ® MultiSync ™ IntelliBase Audio
User's Manual THANK YOU FOR
CHOOSING AN NEC
® ™ MultiSync IntelliBase Stand — Important —
To help us in our continuing efforts to better serve and support you, and to bring you new and innovative products, please take a few moments to register your new NEC MultiSync monitor.
By returning this card, we confirm your date of purchase and records the model and serial numbers. This facilitates our ability to process warranty claims,
ملخص المحتوى في الصفحة رقم 5
NEC-ADA201 Eng/Fr. manual 9/8/98 12:25 PM Page 5 Quick Start ™ How to attach IntelliBase Audio to your ® MultiSync brand monitor MAKE SURE THE MONITOR IS DISCONNECTED FROM THE SYSTEM AND IS UNPLUGGED FROM THE WALL OUTLET BEFORE ANY WORK IS DONE ON THE MONITOR. FOR 21-INCH MONITORS, IT IS ADVISED THAT TWO PEOPLE ARE INVOLVED DURING THE ENTIRE INSTALLATION PROCESS. To attach the IntelliBase to your MultiSync brand monitor, the original base must first be removed. Depending on the model of your
ملخص المحتوى في الصفحة رقم 6
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 6 MultiSync Monitor Model Names MultiSync 50, MultiSync 70, XV15 and XV15+ Step 1 With the monitor MONITOR IN POSITION TO REMOVE THE BASE AND ATTACH unplugged from your INTELLIBASE AUDIO system and the wall BASE outlet, carefully turn the monitor upside down on a firm table so that the base is facing up as shown in Figure 1. Figure 1 Step 2 Using a Phillips screwdriver, remove the screw securing the original base to the monitor as shown in Figure
ملخص المحتوى في الصفحة رقم 7
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 7 Figure 2B Step 3 Locate Adapter Plate “A” that is supplied with ADAPTER PLATE (A) the IntelliBase GUIDE SPINDLE THROUGH CENTER SPINDLE and secure it to HOLE ON ADAPTER PLATE (A) the spindle using the screw that was removed in Step 2 as shown in Figure 2B. Step 4 Locate the two Figure 2C screws that are supplied with INTELLIBASE ROTATE ADAPTER the IntelliBase (BOTTOM VIEW) PLATE UNTIL IT ALIGNS WITH and attach the THROUGH HOLES IntelliBase to O
ملخص المحتوى في الصفحة رقم 8
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 8 MultiSync Monitor Model Names MultiSync 90, XE15, XE17, XP15, XP17, XV17, XV17+, A500, A500+ A700, A700+, A900, E500, E700, E900, E900+, M500, M700 and P750 MONITOR IN POSITION TO Step 1 With the monitor REMOVE THE BASE AND ATTACH INTELLIBASE AUDIO unplugged from your BASE system and wall outlet, carefully turn the monitor upside down on a firm table so that the base is facing up as shown in Figure 1. Figure 1 Step 2 Using your thumbs, push on
ملخص المحتوى في الصفحة رقم 9
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 9 ORIGINAL MOUNTING Step 3 Using a Phillips screwdriver, remove Figure 3B the screw securing RETAIN the two base halves THESE PARTS TO together as shown USE IN NEW in Figure 3B. MOUNTING Retain the screw and black nylon washer for use in the next step. NEW MOUNTING Step 4 Locate Adapter Plate “B” that is supplied with Figure 3C the IntelliBase and BASE secure it to the spindle using the screw and black nylon washer that was removed in Step 2 ADAP
ملخص المحتوى في الصفحة رقم 10
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 10 Figure 3E Step 6 Locate the two screws that are supplied INTELLIBASE with the ROTATE ADAPTER (BOTTOM VIEW) PLATE UNTIL IT IntelliBase ALIGNS WITH THROUGH HOLES and attach ON THE BASE the IntelliBase to the adapter plate and monitor as shown in Figure 3E. Proceed to Page 10 to connect your MultiSync monitor with IntelliBase Audio to your system. MultiSync Monitor Model Names MultiSync XE21, XP21, E1100, E1100+, P1150 and P1250+ MONITOR IN POSIT
ملخص المحتوى في الصفحة رقم 11
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 11 Step 2 Using a Phillips screwdriver, remove the three screws securing the original base to the monitor. Remove the base by sliding and lifting as shown in Figure 4A. Save these screws for use in Step 5. Save the original base for possible future use. Figure 4A ORIGINAL MOUNTING Step 3 Using a Phillips Figure 4B screwdriver, remove RETAIN the screw securing THESE PARTS TO the two base USE IN NEW halves together MOUNTING as shown in Figure 4B. R
ملخص المحتوى في الصفحة رقم 12
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 12 Step 5 After the adapter plate has been attached to Figure 4D the base, snap the base assembly to the monitor. To accomplish this, position all the locking tabs on the base so they mate with the holes in the monitor. Slide the base assembly in place as shown in Figure 4D. Step 6 Using two of the screws that were Figure 4E removed in Step 2, attach the adapter plate assembly to the monitor. To accomplish this, it will be necessary to turn the a
ملخص المحتوى في الصفحة رقم 13
NEC-ADA201 Eng/Fr. manual 9/8/98 12:26 PM Page 13 Step 8 Locate the two Figure 4G screws that are supplied with the IntelliBase INTELLIBASE ROTATE ADAPTER (BOTTOM VIEW) PLATE UNTIL IT and attach the ALIGNS WITH IntelliBase to THROUGH HOLES ON THE BASE the adapter plate and monitor as shown in Figure 4G. Proceed below to connect your MultiSync monitor with IntelliBase Audio to your system. ® How to connect your MultiSync monitor ™ with IntelliBase Audio to your system Figure 5 Step 1 Having su
ملخص المحتوى في الصفحة رقم 14
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 14 Step 2 Connect one end of the supplied audio cable to the audio input jack on the rear of the IntelliBase (Detail B) and the other end to the audio (line) output jack of your computer system (Detail A) as shown in Figure 6. Figure 6 – REAR VIEW AUDIO LINE OUTPUT DETAIL A DETAIL B SEE SEE DETAIL B DETAIL A Figure 7 Step 3 Connect one end of the supplied AC adapter to the DC input jack on the rear of the IntelliBase and the other end into any 11
ملخص المحتوى في الصفحة رقم 15
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 15 Controls ™ POWER: Press the power button to turn the IntelliBase on or off. An indicator light above the button will glow to show power is on. MUTE: If it is necessary to temporarily mute the sound, press this button. When the indicator light above the button glows, the sound is muted. Press the button again to restore sound. VOLUME: Turn this control clockwise to increase volume level. Turn counter- clockwise to decrease volume level. TRE
ملخص المحتوى في الصفحة رقم 16
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 16 Specifications Speakers One 75 mm / 3 inch woofer Four 28 mm / 1.1 inch full range Power (Satellites) 4 + 4 Watts @ 4 Ohms with 10% THD Power (Subwoofer) 5 Watts @ 4 Ohms with 10% THD Input Impedance >10k Ohms Input Sensitivity 300mV input for full output Frequency Response 80Hz - 20kHz S/N Ratio > 60 dB Power Requirements AC 110-120V / 60Hz Current Rating 0.2A @ 120V Headphone Output Impedance 32 Ohms Headphone Jack Type 3.5 mm Stereo Audio I
ملخص المحتوى في الصفحة رقم 17
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 17 Troubleshooting SYMPTOMS POSSIBLE PROBLEM SOLUTION NOTE No Sound No power to unit. Make sure all connecting plugs Provided power has been From between the IntelliBase and verified, it is possible to test Speakers computer are fully seated. the unit by disconnecting Make sure the wall power outlet the audio cable that is or power strip has power. connected to the computer Make sure the power switches and reconnecting it to an on the power st
ملخص المحتوى في الصفحة رقم 18
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 18 References • BBS (978) 742-8706 NEC Technologies Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k bps, no parity, 8-data bits, 1 stop bit • Customer Service Technical Support (800) 632-4662 Fax (978) 742-7049 • Electronic Channels: Internet e-mail: tech-support@nectech.com Internet ftp site: ftp.nectech.com World Wide Web: http://www.nec.
ملخص المحتوى في الصفحة رقم 19
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 19 Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NECTECH’s sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or units ma
ملخص المحتوى في الصفحة رقم 20
NEC-ADA201 Eng/Fr. manual 9/8/98 12:27 PM Page 20 Notes 17
