ملخص المحتوى في الصفحة رقم 1
Elo Entuitive Touchmonitor
User Guide
For 18.1" LCD Modular Kiosk Touchmonitors
1847L Series
Revision A
ملخص المحتوى في الصفحة رقم 2
Elo Entuitive Touchmonitor User Guide 18.1" LCD Modular Kiosk Touchmonitor 1847L Series Revision A P/N 008566 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
ملخص المحتوى في الصفحة رقم 3
Copyright © 2003 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
ملخص المحتوى في الصفحة رقم 4
iv
ملخص المحتوى في الصفحة رقم 5
Table of Contents Chapter 1 Chapter 3 Introduction 1 Operation 23 Precautions . . . . . . . . . . . . . . . . . . . . 1 About Touchmonitor Adjustments . . . . . . . . 23 About the Product . . . . . . . . . . . . . . . . . 1 Using the On-Screen Display (OSD) Menus . . 23 Remote OSD Buttons . . . . . . . . . . . . . 24 Chapter 2 OSD Menu Function . . . . . . . . . . . . . . 25 3 Installation and Setup Unpacking Your Touchmo
ملخص المحتوى في الصفحة رقم 6
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in LCD display design. This combination of features creates a natural flow of information between a user and your touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. See Appen
ملخص المحتوى في الصفحة رقم 7
Auto adjustment capability High quality full screen re-scaling Multilingual OSD menus in six languages: English, French, German, Spanish, Italian and Japanese Serial or USB touch interface (USB requires Windows 98, 2000, Me and XP.) Patented touch technology of Elo TouchSystems Power saving mode Cable management device VESA flat panel monitor physical mounting interface (Both of 75 & 100mm) Remote OSD and Power button lockouts Cable stain reliefs for all cables For full Pro
ملخص المحتوى في الصفحة رقم 8
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 10 items are present and in good condition: OR Serial touchscreen cable USB Cable LCD Display Monitor power cable (US/Canada) Video cable Quick Install Guide CD Software European monitor power cable Adapter User Guide-on CD, Quick Install Guide and software CD OSD Remote DVI-D Video c
ملخص المحتوى في الصفحة رقم 9
Product Overview Main Unit 1847L with optional bezel for front mounting 1847L Rear-Mount Rear View 1847L with front mount 1847L Bottom View (1847L shown) 2-4 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 10
Attaching the L-Brackets Depending on your mounting scheme, use the L-brackets or the VESA 75/100mm standard holes located on the back of the kiosk monitor or the 5.5 diameter holes (only on rear mount). See page 15 for VESA mounting information. NOTE: You will need a screwdriver to attach the L-brackets. Your kiosk touchmonitor comes with a mounting bracket (C-bracket) attached at the back. Included are two L-brackets (and four screws) that attach to both ends of the C-bracket for additional
ملخص المحتوى في الصفحة رقم 11
Panel Cut Outs 1847L Option 1 TOP TOP 2-6 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 12
1847L Option 2 TOP 2-7
ملخص المحتوى في الصفحة رقم 13
1847L Option 3 TOP 2-8 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 14
1847L with 819602-000 Option 1 TOP 2-9
ملخص المحتوى في الصفحة رقم 15
1847L with 819602-000 Option 2 Top 2-10 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 16
Touch Interface Connection Your touchmonitor comes with one of the following touchscreen connector cables: Serial (RS-232) cable or USB cable. (For Windows 98, 2000, Me and XP systems only.) To set up this display, please refer to the following figures and procedures: Serial or USB Connection The following illustrations guide you step by step in connecting your touchmonitor using a serial or USB cable connection CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the c
ملخص المحتوى في الصفحة رقم 17
STEP 1-Connecting the Video Cable VIDEO PORT CONNECTIONS ON UNDERSIDE VIDEO CABLE FEMALE DVI-D FEMALE 15-PIN VIDEO CONNECTOR VIDEO CONNECTOR or 24-pin DVI-D cable • Connect the 15-pin video cable (the ferrite bead end) to the video port on your PC. Connect the other end of the video cable to the video connector on your touchmonitor. Secure the cable to your touchmonitor and PC by turning the screws on the connector clockwise. 2-12 E l o E n t uitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 18
STEP 2-Connecting the Serial or USB Touchscreen Cable CONNECTORS ON THE UNDERSIDE SERIAL TOUCHSCREEN CABLE USB CONNECTOR FEMALE 9-PIN SERIAL TOUCHSCREEN CONNECTOR Connect the female end of the serial (RS-232) cable to the serial port on your PC, or connect the USB touchscreen cable to the USB touchscreen connector on the back of your touchmonitor. Connect the male end of the cable to the serial touchscreen connector on your touchmonitor, or connect the other end of the USB touchscreen ca
ملخص المحتوى في الصفحة رقم 19
STEP 3-Connecting the OSD Remote Cable CONNECTIONS ON UNDERSIDE OSD Remote Connect the 6-pin Remote OSD DIN cable to the black Remote OSD port of the monitor. 2-14 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e
ملخص المحتوى في الصفحة رقم 20
STEP 4-Connecting the Power Cable CONNECTIONS ON UNDERSIDE POWER CABLE POWER Depending on where you live, you will use either the European or US/Canadian power cable. Connect the female end of the power cable to the Brick power supply. Connect the Brick power cable into the power port on the touchmonitor. Route the cable through the cable management channel. NOTE: To protect your equipment against risk of damage from electrical surges in the power line, plug the touchmonitor’s power cord
