ملخص المحتوى في الصفحة رقم 1
Install drivers
SAMTRON 591S/58V/59E/78E/78DF/78BDF/98PDF
ملخص المحتوى في الصفحة رقم 2
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Important to read and understand at Prohibited all times Do not disassemble Disconnect the plug from the outlet Grounding to prevent an electric Do not touch shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same
ملخص المحتوى في الصفحة رقم 3
This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause an electric shock or fire. Disconnect the plug from the outlet during storms or lig
ملخص المحتوى في الصفحة رقم 4
Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor may cause injury by falling. Set down the monitor carefully. The monitor could be damaged or broken. Do not place the monitor face down. The CDT surface may be damaged. Do not use the monitor without the monitor stand. It could break down or cause fire due to bad ventilation. If the monitor must be used witho
ملخص المحتوى في الصفحة رقم 5
You may buy a recommended detergent at any Service Center. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector may cause an electric shock or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center. Others Do not re
ملخص المحتوى في الصفحة رقم 6
Do not use or store inflammable substances near the monitor. This may cause an explosion or fire. Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable. Never insert anything metallic into the monitor openings.
ملخص المحتوى في الصفحة رقم 7
SAMTRON 591S/58V/59E Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor Manual Warranty Card User's Guide, Monitor Quick Setup Guide (Not available in all Driver locations) Cable Power Cord
ملخص المحتوى في الصفحة رقم 8
Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) DC Power Cord Stand Multimedia Speaker Stand Front
ملخص المحتوى في الصفحة رقم 9
Opens the OSD menu. Also used to exit the OSD menu or Menu button [ ] return to the previous menu. Adjust buttons [ ] These buttons allow you to highlight and adjust items in the menu. Used to select the OSD menu. Enter button [ ] Use this button for turn the monitor on and off. Power button This light glows green during normal operation, and blinks green Power indicator once as the monitor saves your adjustments. See PowerSaver described in the manual for further information r
ملخص المحتوى في الصفحة رقم 10
(The configuration at the back of the monitor may vary from product to product.) Connect the power cord for your monitor to the power port on Power port the back of the monitor. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. See Connecting the Monitor for further information regarding cable connections. Bottom Connect the signal cable to the video port on your computer, Signal Cable video board, v
ملخص المحتوى في الصفحة رقم 11
SAMTRON 78E/78DF/78BDF/98PDF Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking Monitor Manual Warranty Card User's Guide, Monitor Quick Setup Guide (Not available in all Driver locations) Cable Power Cord
ملخص المحتوى في الصفحة رقم 12
Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) DC Power Cord Stand Multimedia Speaker Stand Front
ملخص المحتوى في الصفحة رقم 13
Menu button [ ] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the Adjust buttons [ ] menu. Used to select the OSD menu. Enter button [ ] Power button Use this button for turn the monitor on and off. This light glows green during normal operation, and blinks green Power indicator once as the monitor saves your adjustments. See PowerSaver described in the manual for further information re
ملخص المحتوى في الصفحة رقم 14
Connect the signal cable to the video port on your computer, Signal Cable video board, video card, or graphics card. See Connecting the Monitor for further information regarding cable connections. Bottom Connect the signal cable to the video port on your computer, Signal Cable video board, video card, or graphics card. Power port Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor. Tilt/Swivel Ba
ملخص المحتوى في الصفحة رقم 15
SAMTRON 591S/58V/59E Setup-For Multimedia model | Multimedia Speaker Stand 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Connecting to a computer 2-1. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Connecting to a new Macintosh Connect the monitor to the Macintosh computer using the D-SUB connection cable. Connecting to an old Macintosh
ملخص المحتوى في الصفحة رقم 16
1. Turn off your computer and unplug the power cord. Connect the end of the signal cable to your computer's video port(video board, video card or 2. graphics card). 3. Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand. 4. Plug the DC power cord from the stand into a nearby outlet. 5. Connect the power cord for your monitor to the power port on the back o
ملخص المحتوى في الصفحة رقم 17
5. On/Off Volume Turns On/Off and adjusts the output volume. 6. Treble Control Use to control high frequencies. 7. Bass Control Use to control low frequencies. 8. Mic Input Jack To transmit your voice,connect a microphone to this jack. 9. Headphone Jack To listen in privacy,connect headphones here. 10. Detachable Stand Top Tilt/Swivel Base | Attaching and Removing the Base Tilt/Swivel Base With the built-in pedestal, you can tilt and/or swivel the monitor for
ملخص المحتوى في الصفحة رقم 18
Remove the twist-tie before attaching the base to the monitor. Attaching the Base 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base onto the monitor until the tabs are fully engaged in the slots. 4. Push the base toward the front of the monitor until the release latch clicks into the locked position. * Do not bend the snap. Removing the Base 5. Squeeze and pull up on the
ملخص المحتوى في الصفحة رقم 19
1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button. 4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Monitor Homepage http://www.s
ملخص المحتوى في الصفحة رقم 20
3. Click "Display" icon and choose the "Settings" tab then click "Advanced..". 4. Click the " " button on the " " tab and select " " tab. Properties Monitor Driver 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
