ملخص المحتوى في الصفحة رقم 1
INSTALLATION/OPERATION
600 Series Flat Panel
Plasma Monitors
C2938M (12/06)
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Description . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 4
List of Illustrations 1 Parts List Illustration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3 Connecting S-Video Input . . . . . . . . .
ملخص المحتوى في الصفحة رقم 5
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of t
ملخص المحتوى في الصفحة رقم 6
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
ملخص المحتوى في الصفحة رقم 7
Description The 600 Series high performance plasma monitors are designed to fit the specific needs of the security industry. The plasma monitors work well ® ™ using the VGA output of a Pelco DVR or the DVI output of an Endura system. For viewing multiple cameras simultaneously in high definition quality on the plasma monitor, Pelco recommends using PMVC4 and PMVR2 multiviewers. The PMVC4 can accept up to four composite inputs while the PMVR2 can accept up to two DVI or V
ملخص المحتوى في الصفحة رقم 8
Installation The monitor can be placed on any flat surface (desk or table), or it can be wall mounted. You can remove the desktop stand by removing the screws that secure it to the monitor. NOTE: Only use a recommended wall mount kit, such as the PMCP-WM, PMCP-WMT, or PMCP-WM60. To wall-mount the monitor, follow the instructions supplied with the optional mount kit. Refer to manual C2230M for the wall mount kit instructions. DESKTOP STAND You can remove the desktop stand by removi
ملخص المحتوى في الصفحة رقم 9
1. External Speaker Output: Line-out connections to a pair of amplified speakers or amplifier. 2. RS-232 Connector: For authorized service use. 3. DVI Input: Connection to digital video signals from a computer or any Pelco device with DVI output, especially PMVC4 and PMVR2 multiviewers. 4. RGB (VGA) Input: Connection to RGB (VGA) output of a computer or any Pelco device with VGA output, especially PMVC4 and PMVR2 multiviewers. 5. Component Video Input: Auto-dete
ملخص المحتوى في الصفحة رقم 10
VIDEO AND AUDIO CONNECTIONS CONNECTING S-VIDEO INPUT Refer to Figure 3. To use S-Video input, do the following: 1. Connect the external device’s S-Video (4-pin DIN) connector to the monitor’s S-VIDEO INPUT connector. 2. Connect the device’s red (R) and white (L) audio jacks to the monitor’s R and L audio-in jacks of the Video Input. Figure 3. Connecting S-Video Input CONNECTING COMPONENT VIDEO INPUT Refer to Figure 4. To use component video input, do the following: 1. Connect the ex
ملخص المحتوى في الصفحة رقم 11
CONNECTING VIDEO INPUT Refer to Figure 5. To use video input, do the following: 1. Connect the external device’s jack to the monitor’s VIDEO INPUT jack. 2. Connect the device’s red (R) and white (L) audio jacks to the monitor’s R and L audio-in jacks of the Video Input. Figure 5. Connecting Video Input CONNECTING MONITOR OUTPUT Refer to Figure 6. To use monitor output, do the following: 1. Connect the jack from the DVR or VCR (for recording) or audio system to the monitor’s MONITOR O
ملخص المحتوى في الصفحة رقم 12
CONNECTING DVI INPUT Refer to Figure 7. To use DVI (Digital Video Interface) input, do the following: 1. Connect the DVI-jack of the Pelco multiviewer, Endura, or computer to the monitor’s DVI input jack. 2. Connect the device’s red (R) and white (L) audio jacks to the monitor’s R and L audio-in jacks located next to the DVI connector. Audio might be used with DVD players or PCs. MULTIVIEWER Figure 7. Connecting DVI Input CONNECTING EXTERNAL AMPLIFIED SPEAKERS Refer to Figure 8. You
ملخص المحتوى في الصفحة رقم 13
PC CONNECTIONS USING RGB (VGA) OR DVI VIDEO INPUT Refer to Figure 13. 1. Connect the PC’s 15-pin D-Sub RGB (VGA) connector to the monitor’s RGB-IN connector. If you have a PC that is equipped with a DVI, you can connect the PC DVI connector from the PC to the monitor’s DVI-IN connector. 2. For either RGB (VGA) or DVI, connect the PC’s audio jack to the monitor’s R and L (DVI/RGB) audio-in jacks. OR PC PC Figure 9. PC Connections for VGA or DVI CONNECT POWER Plug the provided power
ملخص المحتوى في الصفحة رقم 14
SETTING UP YOUR PC IN WINDOWS FOR USE WITH MONITOR USING A VGA CONNECTOR ® The display settings for a typical Windows -based computer are shown below. However, the actual screen on your computer will differ depending on the Windows version and video card in the computer. The basic setup will apply in most cases even though the actual screen may look different from the example below. 1. Go to the Windows’ Control Panel by clicking START/SETTINGS/CONTROL PANEL. The system displays t
ملخص المحتوى في الصفحة رقم 15
5. If a vertical-frequency option is available, set the value to 60 Hz (refer to Figure 12). Figure 12. Plug and Play Screen 6. Click OK to complete the setting. NOTE: Both screen position and size will vary depending on the type of PC graphics card and its selected resolution. C2938M (12/06) 15
ملخص المحتوى في الصفحة رقم 16
Operation FRONT PANEL CONTROLS Figure 13. PMCP42 and PMCP50 Front Panel Controls Figure 14. PMCP60 Front Panel Controls The following apply to all models. 1. INPUT: Switches between available inputs. 2. MENU: Engages the OSD (on-screen display) menu. 3. VOL: Adjusts volume up and down. These buttons also serve as navigation and adjustment keys when the OSD menu is engaged. 4. and : Navigates through the OSD menu. 5. (power/standby button): Turns on/off power from st
ملخص المحتوى في الصفحة رقم 17
INSTALLING REMOTE CONTROL BATTERIES Figure 15. Battery Installation Refer to Figure 15 for the following procedure. 1. Open and remove the battery cover on the back of the remote control. 2. Install two AAA size 1.5 V batteries (supplied). Match the + and – signs on the batteries to the signs on the battery compartment. 3. Close the battery cover. Make sure the lock snaps closed. WARNING: • Dispose of batteries in a designated disposal area. Do not throw batteries into a fire. •
ملخص المحتوى في الصفحة رقم 18
REMOTE CONTROL FUNCTIONS Figure 16. Remote Control Functions 1. MUTE: Turns on/off sound. 2. POWER: Switches the monitor from standby mode to on, and back to standby mode. 3. LOCATE: Selects a location for the subpicture. Available in PIP (picture-in-picture) mode only. 4. SIZE: Selects a size for the subpicture. Available in PIP mode only. 5. SWAP: Switches the main picture and subpicture. Available in PIP and PBP modes only. (PBP is picture-by-picture, which is two images of
ملخص المحتوى في الصفحة رقم 19
6. A.SWAP: Selects audio for the main or subpicture. Available in PIP and PBP modes only. 7. SPLIT: Selects a PIP mode (NORMAL, PIP, PBP). 8. S.SELECT: Selects the main picture or subpicture. Then you can adjust the status of the selected picture. Available in PIP and PBP modes only. When in PIP or PBP mode, this button lets you put “focus” on either the subpicture (PIP) or the main picture. For example, select the subpicture. Any adjustment made to the pictu
ملخص المحتوى في الصفحة رقم 20
BASIC FUNCTIONS POWERING ON/OFF Make sure the monitor is plugged into the wall outlet with the supplied power cord. The STATUS LED on the control panel will glow red. 1. Press the on/off button on the front panel or the POWER button on the remote control. The monitor will turn on after a brief pause. The STATUS LED will turn green to indicate power is on. 2. Turn off the power by again pressing the on/off button on the front panel or the POWER button on the remote control. SE
