ملخص المحتوى في الصفحة رقم 1
MultiSync LCD175VXM+
MultiSync LCD195VXM+
User’s Manual
ملخص المحتوى في الصفحة رقم 2
WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS IN
ملخص المحتوى في الصفحة رقم 3
For the Customer to use in U.S.A. or Canada Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouiller du Canada. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CSA C22.2 No. 60950-1. Ce produit porte la marque ‘C-UL’ et se conf
ملخص المحتوى في الصفحة رقم 4
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt base • Audio Cable • Power Cord •Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •Video Signal Cable (DVI-D to DVI-D) (LCD195VXM+ only) • User’s Manual • CD-ROM • Cable management cover Cable management CD-ROM cover User’s Manual Audio Cable Power Cord 15-pin mini D-SUB DVI-D to DVI-D MultiSync LCD monitor male to 15-pin mini (LCD195VXM+ only) D-SUB male * Rememb
ملخص المحتوى في الصفحة رقم 5
3. To attach the Cable management cover: Insert the tabs of the Cable management cover into the holes of Stand neck and slide the Cable management cover downward into place (Figure A.4). NOTE: Please confirm that the tabs are completely secure. 4. Connect all cables to the appropriate connector on the back of the monitor Stand (Figure B.1). Connect the Headphone (not included) to the appropriate connector at the rear side of the monitor (Figure C.1). 5. Connect one end of the power cord to the m
ملخص المحتوى في الصفحة رقم 6
Remove Monitor Stand for Mounting To prepare the monitor for alternative mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface (Figure R.1). 3. Remove the 4 screws connecting the monitor to the stand and remove the stand as indicated (Figure R.2). The monitor is now ready for mounting in an alternative manner. 4. Connect the AC cord and signal cables to the back of the monitor (Figure R.3). 5. Reverse this process to re-attach stand. NOTE: Use only VES
ملخص المحتوى في الصفحة رقم 7
Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key SELECT 1<->2 / RESET – + Button At No OSD Shortcut to Bright adjust Shortcut to Volume adjust Input signal select. Showing OSM. showing window. window. At OSD showing Go to Adjustment stage. Cursor goes to left. Cursor goes to right. (Icon selection stage) At OSD showing Go to Icon selection stage. Adjust value decrease or Adjust value increase or Reset operati
ملخص المحتوى في الصفحة رقم 8
AUDIO Control the sound volume of speakers and headphone. To mute the speaker sound, press the 1<->2/RESET key. BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST (Analog Input only) Adjusts the image displayed for non-standard video inputs. AUTO ADJUST (Analog Input only) Automatically adjusts the Image Position, the H. Size and Fine setting. LEFT/RIGHT (Analog Input only) Controls Horizontal
ملخص المحتوى في الصفحة رقم 9
OSM LOCK OUT This control completely locks out access to all OSM control functions without Brightness and Contrast. When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the OSM are locked out. To activate the OSM Lock Out function, press “1<->2/ RESET”, then “+” key and hold down simultaneously. To de-activate the OSM Lock Out, press “1<->2/ RESET”, then “+” key and hold down simultaneously. RESOLUTION NOTIFIER If ON is selected, a message will app
ملخص المحتوى في الصفحة رقم 10
Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. • Do not spill any liquids into the cabinet or use your monitor near water. • Do not insert objects of any kind into the cabine
ملخص المحتوى في الصفحة رقم 11
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. • Position your monitor no closer than 40 cm and no further away than 70 cm from your eyes. The optimal distance is 50 cm. • Rest
ملخص المحتوى في الصفحة رقم 12
Specifications for MultiSync LCD175VXM+ Monitor Specifications MultiSync LCD175VXM+ Monitor Notes LCD Module Diagonal: 43 cm/17 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 43 cm/17 inches liquid crystal display (LCD); 0.264 mm dot 2 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 300 cd/m * white luminance, 700:1 contrast ratio, typical; response time: 5 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI-D Sync: Separate sync.TTL Level (Positive/Ne
ملخص المحتوى في الصفحة رقم 13
Specifications for MultiSync LCD195VXM+ Monitor Specifications MultiSync LCD195VXM+ Monitor Notes LCD Module Diagonal: 48 cm/19 inches Active matrix; thin film transistor (TFT) Viewable Image Size: 48 cm/19 inches liquid crystal display (LCD); 0.294 mm dot 2 2 Native Resolution (Pixel Count): 1280 x 1024 pitch; 300 cd/m * white luminance, 800:1 contrast ratio, typical; response time: 5 ms. Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Digital Input: DVI-D Sync: Separate sync.TTL Level (Positive/Ne
ملخص المحتوى في الصفحة رقم 14
Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another. Colour Control System: Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards. OSM (On-Screen Manager) Controls: Allow you to quickly and easily adjust all elements of your screen
ملخص المحتوى في الصفحة رقم 15
Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check front power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) • Check the monitor and your display card with respect to compatibility and
ملخص المحتوى في الصفحة رقم 16
TCO’03 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in ord
ملخص المحتوى في الصفحة رقم 17
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). Disposin
