ملخص المحتوى في الصفحة رقم 1
ET2639L 26” LCD Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 2
Elo TouchSystems ET2639L 26” LCD Touchmonitor User Guide Revision D P/N E983412 Elo TouchSystems 1-800-ELOTOUCH www.elotouch.com
ملخص المحتوى في الصفحة رقم 3
Copyright © 2008 Tyco Electronics. All Rights Reserved. No part of this publication may be reproduced, transmitted, tran- scribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or other- wise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change with
ملخص المحتوى في الصفحة رقم 4
Table of Contents Chapter 1: Introduction ......................................................................................5 About the Product .............................................................................................................5 Chapter 2: Installation And Setup .....................................................................6 Unpacking Your Touchmonitor ......................................................................................... 7 Interface Conn
ملخص المحتوى في الصفحة رقم 5
C H A P T E R 1 INTRODUCTION About the Product Your new ET2639L Elo TouchSystems Touchmonitor combines the reliable performance of touch technology with the latest advances in Liquid Crystal Display (LCD) design. The monitor comes with the fol- lowing features: • 26” color active matrix thin-fi lm-transistor (TFT) with a native resolution of 1366 X 768. • Available in Acoustic Pulse Recognition (APR), IntelliTouch, SecureTouch, and Surface Capacitive touch technologies. • All
ملخص المحتوى في الصفحة رقم 6
C H A P T E R 2 INSTALLATION AND SETUP This chapter discusses how to install and set up your LCD touchmonitor and how to install Elo TouchSystems driver software. Elo TouchSystems ET2639L User Guide 6
ملخص المحتوى في الصفحة رقم 7
Unpacking Your Touchmonitor Check that the following items are present and in good condition: Power cable Touchmonitor DVI-D cable USB Cable Analog Video (not included with ET2639L-xxxx-x-A-x models) CD and Quick Install Guide OSD Control Box Serial Cable (not included with ET2639L-Axxx models) Elo TouchSystems ET2639L User Guide 7
ملخص المحتوى في الصفحة رقم 8
Interface Connection Connector Panel on Rear side of Monitor Serial Cable (not Power DVI-D cable Power Cable Analog Video OSD box USB cable included with Button (not included with Cable connector ET2639L-Axxx ET2639L-xxxx-x- models) A-x models) To connect your touchmonitor to your computer: 1 Connect the power cable to the rear panel of the monitor and the other end to the power outlet. 2 Connect either the USB cable OR the serial cable to the rear panel of the monitor. Note: Do not u
ملخص المحتوى في الصفحة رقم 9
Installing the Touch Driver Your Elo touchmonitor is Plug-and-Play compliant. Information on the video capabilities of the touchmonitor is sent to the video display adapter when Windows starts. If Windows detects the touchmonitor, follow the instructions on the screen to install a generic Plug-and-Play monitor. Elo TouchSystems provides touch driver software that allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD for the following operating systems:
ملخص المحتوى في الصفحة رقم 10
2 Choose Next. Select “Search for the best driver for your device (Recommended)” and choose Next. 3 When a list of search locations is displayed, place a checkmark on “Specify a location” and use Browse to select the \EloUSB directory on the Elo CD-ROM. 4 Choose Next. Once the Elo TouchSystems touchscreen driver has been detected, choose Next again. 5 You will see several fi les being copied. Insert your Windows 98 CD if prompted. Choose Finish. If Windows XP, Windows 2000,
ملخص المحتوى في الصفحة رقم 11
Monitor Mounting Orientation When the monitor is mounted in the landscape orientation, the cable connection panel must be at the bottom, as shown in the illustration below. Rear View of Monitor—Landscape Orientation Cable connection panel must be at the bottom for proper mounting of the monitor. Alternatively, the monitor may be mounted in the portrait orientation. For this orientation, the cable connection panel may be on either side, as shown in the illustrations below. Rear View of Moni
ملخص المحتوى في الصفحة رقم 12
Landscape Mounting Orientation Angle Views The mounting orientation can be up to a 90° angle from vertical, as shown in the illustrations below. Elo TouchSystems ET2639L User Guide 12
ملخص المحتوى في الصفحة رقم 13
Portrait Monitor Orientation Angle Views The mounting orientation can be up to a 90° angle, as shown in the illustration below. Elo TouchSystems ET2639L User Guide 13
ملخص المحتوى في الصفحة رقم 14
C H A P T E R 3 OPERATION About Touchmonitor Adjustments Your touchmonitor will probably not require adjustment. However, variations in video output and application may require adjustments to your touchmonitor to optimize the quality of the display. For best performance, your video source should be at 1360 x 768 resolution, at 60Hz vertical frame rate. Operating in other resolutions will degrade video performance. For input video outside the vertical frame rate and dot clock range
ملخص المحتوى في الصفحة رقم 15
On-Screen Display (OSD) Control Box OSD Control Buttons The On-Screen Display (OSD) Control Box, included with your ship- ment, allows you to change settings on the monitor screen. It has four buttons: 1 AUTO/SEL (select) 2 DOWN 3 UP 4 MENU OSD Menu Functions Use the control buttons for the following functions: Control Function MENU Displays/exits the OSD Menus UP 1) Enters contrast of the OSD (if no OSD is currently displayed on screen) 2) Increases v
ملخص المحتوى في الصفحة رقم 16
OSD Lock/Unlock You are able to lock and unlock the OSD feature. When the OSD is locked, no OSD can be displayed or used. The monitor is shipped in the unlocked position. To lock the OSD: 1 Press the MENU button and UP button simultaneously for 2 seconds. A window will appear displaying “OSD Unlock.” 2 Continue to hold the buttons down for another 2 seconds and the window toggles to “OSD Lock.” Power Lock/Unlock You are able to lock/unlock the Power feature. When the power is l
ملخص المحتوى في الصفحة رقم 17
OSD Control Options Auto Adjust • Automatically adjusts video timing parameters (of VGA video only). Luminance Brightness • Adjusts the brightness. Contrast • Adjusts the contrast. Geometry (VGA only) H-position • Moves the image left or right on the screen. V-position • Moves the image up or down on the screen. Clock • Stretches the image horizontally. Phase • Adjusts the phase of the dot clock to image data. Color • Sets the color temperature. Input Select • Selects betw
ملخص المحتوى في الصفحة رقم 18
Recall Recall Color • Restores default color temperature settings. Recall Defaults • Restores original factory settings for H-position, V-position, Clock, and Phase for the current video mode (VGA only). • Restores original factory settings for all other parameters and video inputs, except language (VGA and DVI). Miscellaneous Sharpness • Adjusts sharpness of video. Display Information • Frequency of the input horizontal/vertical synchronizing signal is indicated. Elo T
ملخص المحتوى في الصفحة رقم 19
Preset Display Modes The monitor comes with preset settings for commonly used video modes. It will automatically adjust the picture size and centering for any of the video modes listed in Appendix B, ET2639L Specifi cations table, under “Preset Display Modes.” If you make any adjustments to the H-position, V-Position, Clock and Phase video settings via the OSD in a preset display mode, those changes will be automatically saved for that display mode and recalled for any future use of that d
ملخص المحتوى في الصفحة رقم 20
C H A P T E R 4 TROUBLESHOOTING If you are experiencing trouble with your touchmonitor, refer to the fol- lowing table. If the problem persists, please contact your local dealer or our service center. Elo Technical Support numbers are listed on page 33. Solutions to Common Problems Problem Suggestion(s) The monitor does not respond after Check that the monitor’s Power you turn on the system Switch is on. Turn off the power and check the
