ملخص المحتوى في الصفحة رقم 1
Elo Entuitive Touchmonitor
User Guide
For 17" LCD Modular Kiosk Touchmonitors
1746L/1749L Series
Revision B
ملخص المحتوى في الصفحة رقم 2
6 49 B /N 008602E
!" # $%&&$' '( )))#
#
ملخص المحتوى في الصفحة رقم 3
Copyright © 2005 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
ملخص المحتوى في الصفحة رقم 4
ملخص المحتوى في الصفحة رقم 5
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in LCD display design. This combination of features creates a natural flow of information between a user and your touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. See Appen
ملخص المحتوى في الصفحة رقم 6
• Auto adjustment capability • High quality full screen re-scaling • Multilingual OSD menus in five languages: English, French, German, Spanish and Japanese. • Serial and USB touch interface (USB requires Windows 98, 2000, Me or XP.) • Patented touch technology of Elo TouchSystems • VESA DDC 1/2B data communication • VESA DPMS power saving • Cable management device • VESA flat panel monitor physical mounting interface (Both 75 and 100mm) • Remote OSD and Power button lockouts • Cable strain rel
ملخص المحتوى في الصفحة رقم 7
ملخص المحتوى في الصفحة رقم 8
Product Overview Main Unit 1746L Front-Mount 1749L Front-Mount Rear View 1746L 1749L Bottom View (1749L shown) Detail A See Detail A 2-4 Elo Entuitive Tou chmon ito r User Guide
ملخص المحتوى في الصفحة رقم 9
Attaching the L-Brackets Depending on your mounting scheme, use the L-brackets or the VESA 75/100mm standard holes located on the back of the kiosk monitor or the integrated M4 threaded holes. See page 15 for VESA mounting information. NOTE: You will need a screwdriver to attach the L-brackets. Your kiosk touchmonitor comes with two L-brackets (and four screws) that attach to the integrated M4 threaded holes for additional mounting options. 2-5
ملخص المحتوى في الصفحة رقم 10
Panel Cut Outs 1746L/1749L Option 1 1746L/1749L Option 2 2-6 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 11
Touch Interface Connection Your touchmonitor comes with the following touchscreen connector cables: Serial (RS-232) cable and USB cable. (For Windows 98, 2000, Me and XP systems only.) To set up this display, please refer to the following figures and procedures: Serial or USB Connection The following illustrations guide you step by step in connecting your touchmonitor using a serial or USB cable connection CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the comp
ملخص المحتوى في الصفحة رقم 12
STEP 1-Connecting the Video Cable VIDEO PORT ET1749L shown (ET1746L does not have DVI-I connector) VIDEO CABLE FEMALE 15-PIN SERIAL VIDEO CONNECTOR or 29-pin DVI-I cable • Connect the 15-pin video cable (the ferrite bead end) to the video port on your PC. • Connect the other end of the video cable to the video connector on your touchmonitor. • Secure the cable to your touchmonitor and PC by turning the screws on the connector clockwise. 2-8 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 13
ملخص المحتوى في الصفحة رقم 14
ملخص المحتوى في الصفحة رقم 15
STEP 4-Connecting the Power Cable AUTO/SEL DOWN UP MENU ET1749L shown (ET1746L does not have DVI-D connector) POWER CABLE POWER Depending on where you live, you will use either the European or US/Canadian power cable. Brick power supply. • Connect the female end of the power cable to the Connect the Brick power cable into the power port on the touchmonitor. • • Route the cable through the cable management channel. NOTE: To protect your equipment against risk of damage from ele
ملخص المحتوى في الصفحة رقم 16
Optimizing the LCD Display To ensure the LCD display works well with your computer, configure the display mode of your graphic card to make it less than or equal to 1280 x 1024 resolution(1280x1024 is highly recommended), and make sure the timing of the PC video graphic card is compatible with the LCD display. Refer to Appendix A for more information about resolution. Compatible video modes for your touchmonitor are listed in Appendix C. VESA Mount on Your Touchmonitor Your touchmonitor confo
ملخص المحتوى في الصفحة رقم 17
VESA Mounting Interface Your monitor has standard VESA mounting holes on the rear of the unit. The holes are spaced at 75mm and 100mm standard separations. The following companies provide VESA mounting devices compatible with your touchmonitor: Ergotron Innovative Office Products 800-888-8458 800-524-2744 651-681-7600 610-253-9554 www.ergotron.com www.innov-office-prod.com GCX MRI 800-228-2555 800-688-2414 707-773-1100 www.mediarecovery.com www.gcx.com 2-13
ملخص المحتوى في الصفحة رقم 18
Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: • Windows XP • Windows 2000 • Windows Me • Windows 98 • Windows 95 • Windows NT 4.0 Additional drivers and driver information for other operating systems are available on the Elo TouchSystems web site at www.elotouch.com. Your Elo touchmonitor is plug-and-play compliant. Information on
ملخص المحتوى في الصفحة رقم 19
Installing the Serial Touch Driver Installing the Serial Touch Driver for Windows XP, Windows 2000, Me, 95/98 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the CD and starts the setup program. 3 Follow the directions on the screen to complete the driver setup for your version of Wi
ملخص المحتوى في الصفحة رقم 20
Installing the Serial Touch Driver for MS-DOS and Windows 3.1 You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS. To install Windows 3.x and MS-DOS from Windows 95/98, follow the directions below: 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
