ملخص المحتوى في الصفحة رقم 1
Elo Entuitive Touchmonitor
User Guide
For 18.1" LCD Desktop Touchmonitors
1825L/1827L Series
Revision C
ملخص المحتوى في الصفحة رقم 2
Elo Entuitive Touchmonitor User Guide 18.1" LCD Desktop Touchmonitor 1825L/1827L Series Revision C P/N 008563 Elo TouchSystems, Inc. 1-800-ELOTOUCH www.elotouch.com
ملخص المحتوى في الصفحة رقم 3
Copyright © 2004 Elo TouchSystems Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo TouchSystems. Disclaimer The information in this document is subject to change without notice. Elo TouchSystems makes no
ملخص المحتوى في الصفحة رقم 4
Table of Contents Chapter 1 Chapter 3 Introduction 1 Operation 19 Precautions . . . . . . . . . . . . . . . . . . . . 1 About Touchmonitor Adjustments. . . . . . . . 19 About the Product . . . . . . . . . . . . . . . . . 1 Using the On-Screen Display (OSD) Menus . . 19 Side Bezel Buttons . . . . . . . . . . . . . . . 20 Chapter 2 OSD Menu Function . . . . . . . . . . . . . . 21 Auto Adjustment . . . . . . . . . . . . . . . . 22 Installatio
ملخص المحتوى في الصفحة رقم 5
C H A P TER 1 C HAPT ER 1INTRODUCTION Congratulations on your purchase of an Elo TouchSystems Entuitive touchmonitor. Your new touchmonitor combines the reliable performance of Elo’s touch technology with the latest advances in LCD display design. This combination of features creates a natural flow of information between a user and your touchmonitor. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. See Appen
ملخص المحتوى في الصفحة رقم 6
Auto adjustment capability High quality full screen re-scaling Multilingual OSD menus in five languages: English, French, Deutsch Spanish and Japanese Serial or USB touch interface (USB requires Windows 98, 2000, Me and XP.) Built in speakers with volume, treble, bass and balance control through OSD Patented touch technology of Elo TouchSystems Power saving mode o Stand with minimum 95 angle of tilt. Cable management device VESA flat panel monitor physical mounting interfa
ملخص المحتوى في الصفحة رقم 7
C H A P TER 2 C HAP TER 2INSTALLATION AND SETUP This chapter discusses how to install your LCD touchmonitor and how to install Elo TouchSystems driver software. Unpacking Your Touchmonitor Check that the following 10 items are present and in good condition: OR Serial touchscreen cable USB Cable LCD Display Speaker cable Video cable Monitor power cable DVI-D video cable Quick Install Guide (US/Canada) CD Software European monitor Adapter power cable User Guide-on CD, Quick Install Guide and soft
ملخص المحتوى في الصفحة رقم 8
Product Overview Main Unit LCD Display Stand Rear View 2-4 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 9
Side View User Controls Base Bottom View Key hole for M5 screw 4X thread M5x0.8 2-5
ملخص المحتوى في الصفحة رقم 10
Touch Interface Connection Your touchmonitor comes with one of the following touchscreen connector cables: Serial (RS-232) cable or USB cable. (For Windows 98, 2000, Me and XP systems only.) To set up this display, please refer to the following figures and procedures: Serial or USB Connection The following illustrations guide you step by step in connecting your touchmonitor using a serial or USB cable connection CAUTION Before connecting the cables to your touchmonitor and PC, be sure that the c
ملخص المحتوى في الصفحة رقم 11
STEP 1-Routing the Cables Feed the cables through the cable port holes. Do not remove the rear cover. 2-7
ملخص المحتوى في الصفحة رقم 12
STEP 2-Connecting the Video Cable CONNECTIONS ON UNDERSIDE VIDEO PORT FEMALE 15-PIN VIDEO CONNECTOR VIDEO CABLE • Tilt the screen up and back to access the connection ports. (the ferrite bead end) or 24-pin DVI-D cable • Connect the 15-pin video cable your PC. to the video port on • Connect the other end of the video cable to the video connector on your touchmonitor by routing the cable through the hole in the stand. • Secure the cable to your touchmonitor and PC by turning the screws on the
ملخص المحتوى في الصفحة رقم 13
STEP 3-Connecting the Serial or USB Touchscreen Cable CONNECTORS ON THE UNDERSIDE USB TOUCHSCREEN CONNECTOR FEMALE 9-PIN SERIAL TOUCHSCREEN CONNECTOR SERIAL TOUCHSCREEN CABLE • Connect the female end of the serial (RS-232) cable to the serial port on your PC, or connect the USB touchscreen cable to the USB touchscreen connector on the back of your touchmonitor. • Connect the male end of the cable to the serial touchscreen connector on your touchmonitor, or connect the other end of the USB to
ملخص المحتوى في الصفحة رقم 14
STEP 4-Connecting the Speaker Cable CONNECTIONS ON UNDERSIDE SPEAKER PORT SPEAKER CABLE NOTE: If you do not wish to connect the speaker cable, go to step 5. • Connect the light blue end of the speaker cable to the light blue speaker port of the monitor (audio in). • Connect the lime (light green) end of the speaker cable to the lime speaker port on the computer (audio out). 2-10 Elo Entuitive Touchmonitor User Guide
ملخص المحتوى في الصفحة رقم 15
STEP 5-Connecting the Power Cable CONNECTIONS ON UNDERSIDE POWER BRICK POWER SUPPLY POWER CABLE Depending on where you live, you will use either the European or US/Canadian power cable. • Connect the female end of the power cable to the Brick power supply. Connect the Brick power cable into the power port on the touchmonitor. • • Route the cable through the cable management channel. NOTE: To protect your equipment against risk of damage from electrical surges in the power line, plug the touchm
ملخص المحتوى في الصفحة رقم 16
Optimizing the LCD Display To ensure the LCD display works well with your computer, configure the display mode of your graphic card to make it less than or equal to 1024 x 768 resolution, and make sure the timing of the display mode is compatible with the LCD display. Refer to Appendix A for more information about resolution. Compatible video modes for your touchmonitor are listed in Appendix C. VESA Mount on Your Touchmonitor Your touchmonitor conforms to the VESA Flat Panel Monitor Physic
ملخص المحتوى في الصفحة رقم 17
Accessing the VESA Mounting Interface If you want to convert your desktop monitor to a wall mount or kiosk monitor, follow the steps below to access the VESA mounting interface. NOTE: You will need a screwdriver for the following steps. 1 Remove the back cover of the stand by pulling forward on the bottom cut-out. 2 Carefully lay the monitor face down. At the top of the mounting screw cover there are two slots. With a screwdriver, pry open the mounting screw cover. The cover fit is tight so
ملخص المحتوى في الصفحة رقم 18
Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmonitor to work with your computer. Drivers are located on the enclosed CD-ROM for the following operating systems: Windows XP Windows 2000 Windows Me Windows 98 Windows 95 Windows NT 4.0 Additional drivers and driver information for other operating systems are available on the Elo TouchSystems web site at www.elotouch.com. Refer to the appropriate following section for driver installatio
ملخص المحتوى في الصفحة رقم 19
Installing the Serial Touch Driver Installing the Serial Touch Driver for Windows XP, Windows 2000, Me, 95/98 and NT 4.0 NOTE: For Windows 2000 and NT 4.0 you must have administrator access rights to install the driver. 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2 If the AutoStart feature for your CD-ROM drive is active, the system automatically detects the CD and starts the setup program. 3 Follow the directions on the screen to complete the driver setup for your version of Wi
ملخص المحتوى في الصفحة رقم 20
Installing the Serial Touch Driver for MS-DOS and Windows 3.1 You must have a DOS mouse driver (MOUSE.COM) installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS. To install Windows 3.x and MS-DOS from Windows 95/98, follow the directions below: 1 Insert the Elo CD-ROM in your computer’s CD-ROM drive. 2 From DOS, type d:\EloDos_W31 to change to the correct directory on the CD-ROM (your CD-ROM drive may be mapped to a different drive letter).
