ملخص المحتوى في الصفحة رقم 1
USER’S GUIDE
COLOR MONITOR
Model No : 7dln
CTL
S/N : 9978628208
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFEGUARDS FEDERAL COMMUNICATIONS COMMISSION 1. Read all of these instructions. 12. For added protection for this RADIO FREQUENCY INTERFERENCE STATEMENT monitor during a lightning storm, 2. Save these instructions for later use. or when it is left unattended and unused for long periods of time, 3. Unplug this monitor from the NOTE : This equipment has been tested and found to comply with the limits unplug it from the wall outlet. This wall outlet before cleaning. Do not for a Class
ملخص المحتوى في الصفحة رقم 3
CONTENTS INTRODUCTION Introduction ............................................................................. 1 This manual explains how to correctly install, operate and get the best performance from your monitor. Please read this user’s Product Features ................................................................. 2 guide carefully before installing your monitor, then keep it near Setup ......................................................................................... 3 your mon
ملخص المحتوى في الصفحة رقم 4
SETUP PRODUCT FEATURES • The convenient and user-friendly on-screen display allows for INSTALLING THE TILT/SWIVEL STAND easy and accurate adjustments of horizontal and vertical screen size and position, geometry and screen color. 1. Ensure that the power to the monitor is off. • The monitor supports a safe working environment in strict compliance with the MPR II standard for low emissions 2. Set the monitor face down with the underside facing you. (TCO O
ملخص المحتوى في الصفحة رقم 5
OPERATION & ADJUSTMENT CONNECTING THE SIGNAL CABLE AND POWER CORD Control Panel SELECT ADJUST MENU 1. Turn off the computer and monitor. 2. Connect the 15 pin D-sub connector to the output port of the video card in your computer. 3. Tighten the screws of the connector. MENU 4. Plug the power cord into the AC receptacle located on the back • Launch OSD(On-Screen Display) MENU window. of the monitor. SELECT 5. Plug the other end of the power cord into the AC outlet. • Select a sub Menu & function
ملخص المحتوى في الصفحة رقم 6
Key Process OSD Functions ICON CONTROL FUNCTION MENU Adjust the position of the display H. POSITION horizontally (left or right). Adjust the position of the display V. POSITION SELECT vertically (up or down). Adjust the display width (horizontal H.SIZE size). MENU V.SIZE Adjust the display height (vertical size). MENU MENU V. LINEARITY Adjust the vertical linearity. Adjust the horizontal linearity. H. LINEARITY OSD OFF Adjust the left and right margins for PINCUSHION
ملخص المحتوى في الصفحة رقم 7
ICON CONTROL FUNCTION ICON CONTROL FUNCTION Adjust the side pin corner balance top Display horizontal & vertical frequency STATUS T. PIN BALANCE when the top sides of the screen are and polarity. bowed towards left or right. Adjust the horizontal picture moire H. MOIRE Adjust the side pin corner balance bottom cancellation. B. PIN BALANCE when the bottom sides of the screen are bowed towards left or right. Adjust the vertical picture moire V. M
ملخص المحتوى في الصفحة رقم 8
SPECIFICATIONS TROUBLESHOOTING CDT Size 17-inch Symptom Check Diagonal visible image area 16.2-inch Dot Pitch 0.27 mm No picture. Check if POWER SWITCH and COMPUTER Synchronization Horizontal 30 - 70 KHz POWER SWITCH are in the on position. Vertical 50 - 160 Hz Check if the signal cable is correctly connected to Plug and Play DDC1/2B/CI the video card. Power Saving EPA, VESA DPMS, Nutek Compliant Power Source 100-240 Vac, 50/60Hz (Free Voltage) Check if the pins of D-sub connector are not bent
