ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
Safety........................................................................................................................................................................4 National Conventions.........................................................................................................................................4 Power .............................................................................................................................................................
ملخص المحتوى في الصفحة رقم 3
EPEAT Declaration ..........................................................................................................................................55 Service....................................................................................................................................................................56 Warranty Statement for Europe........................................................................................................................56 Warranty Stat
ملخص المحتوى في الصفحة رقم 4
Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damag
ملخص المحتوى في الصفحة رقم 5
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an a
ملخص المحتوى في الصفحة رقم 6
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care. Never push any
ملخص المحتوى في الصفحة رقم 7
Cleaning Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. 7
ملخص المحتوى في الصفحة رقم 8
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. 8
ملخص المحتوى في الصفحة رقم 9
Setup Contents in Box Monitor CD Manual Adaptor DVI Cable Analog Cable HDMI Cable Power Cable Not all signal cables (Analog, USB, DVI, and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation. 9
ملخص المحتوى في الصفحة رقم 10
Setup Stand & Base Please setup the base following the steps as below. Setup: 1. Place monitor on the firm surface (such as, table) 2. Use your hands to hold the monitor base 3. Use your hands to fold the monitor base as figure instructed above by switch safety lock to the right side 4. Once the monitor base begin to fold you can release the safety lock (caution: you must hear “click” after you fold the monitor base to standing position to ensure safety lock is lock properly.)
ملخص المحتوى في الصفحة رقم 11
Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -4° to 14 °. -4 14 NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. 11
ملخص المحتوى في الصفحة رقم 12
Connecting the Monitor Cable Connections On Back of Monitor and Computer: 1 2 3 4 5 1. HDMI 1 HDMI 2 2. 3. D-SUB 4. Audio 5. Power To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3 Connect one end of the HDMI cable to the back of the mon
ملخص المحتوى في الصفحة رقم 13
Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1 Place monitor on the firm surface (such as, table) 2 Use your hands to hold the monitor base 3 Use your hands to fold the monitor base as figure instructed above by switch safety lock to the right side 4 Once the monitor base begin to fold you can release the safety lock (caution
ملخص المحتوى في الصفحة رقم 14
Adjusting Setting Optimal Resolution Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization 14
ملخص المحتوى في الصفحة رقم 15
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 15
ملخص المحتوى في الصفحة رقم 16
Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPLAY. 16
ملخص المحتوى في الصفحة رقم 17
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 17
ملخص المحتوى في الصفحة رقم 18
Hotkeys 4:3 or wide/ wer Auto/Source/Exit Menu/Enter Clear Vision/ > Po Power Press the Power button to turn 0n/off the monitor. Clear Vision/ 1. When there is no OSD, Press the “ ” button to activate Clear Vision 2. Use the “ ” or “ “buttons to select between weak, medium, strong, or off settings. > Default setting is always “off” 3. Press and hold“ “ button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo:
ملخص المحتوى في الصفحة رقم 19
OSD Setting Basic and simple instruction on the control keys. 1. Press the MENU-button to activate the OSD window. 2. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If there is a sub-menu, press or to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. 3. Press or to change the settings of the selected function. Press AUTO to exit.
ملخص المحتوى في الصفحة رقم 20
Luminance 1 Press (Menu) to display menu. 2 Press or to select (Luminance), and press to enter. 3 Press or to select submenu, and press to enter. 20
