ملخص المحتوى في الصفحة رقم 1
SyncMaster 941MW / 941MG
Install Driver
ملخص المحتوى في الصفحة رقم 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, a
ملخص المحتوى في الصفحة رقم 3
Do not use a damaged or loose plug. ! This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. ! This may cause electric shock or fire. Use only a properly grounded plug and receptacle. ! An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. ! A bad connection may cause fire. Do not excessively bend t
ملخص المحتوى في الصفحة رقم 4
Installation Be sure to contact an authorized Service Center, when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. ! Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. ! Failure to do so may cause electric shock or fire inside the monito
ملخص المحتوى في الصفحة رقم 5
! Any increase in the internal temperature may cause fire. Put down the monitor carefully. ! Failing to do so may damage the monitor. Do not place the monitor face down. ! This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. ! Installing the bracket by unqualified personnel may result in injury. ! Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it
ملخص المحتوى في الصفحة رقم 6
Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. ! This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. ! A dirty connector may cause electric shock or fire. Make sure to unplug the power
ملخص المحتوى في الصفحة رقم 7
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center. ! This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. ! This may cause a malfunction, electric shock or fire. ! In particular, avoid operating the monitor near water or outdoors where the monito
ملخص المحتوى في الصفحة رقم 8
Never insert anything metallic into the monitor openings. ! This may cause electric shock, fire or injury. Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc. ! This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. When viewing a fix
ملخص المحتوى في الصفحة رقم 9
Place the product out of children's reach, as they could damage by hanging onto it. ! A falling product may cause injury to the person or even fatality. When not using the product for an extended period of time, keep the product unplugged. ! Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. ! Children may try to
ملخص المحتوى في الصفحة رقم 10
height so that the top of the monitor is slightly below eye level. ! Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. ! Keep your arms level with the back of your hands. ! Keep the angle of the elbow perpendicular. ! Keep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.
ملخص المحتوى في الصفحة رقم 11
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Without Stand With Stand Manual Warranty Card Quick Setup Guide User's Guide, Monitor Driver (Not available in all locations) Cable
ملخص المحتوى في الصفحة رقم 12
D-Sub Cable Audio Cable Power Cord Other Remote Control Batteries (AAA X 2) Sold separately TV Antenna Cable RCA Cable (Video-Yellow, Component(P , P , Y) Cable R B (Coaxial Cable) Audio-Red and White) S-VIDEO Cable Earphones/Headphones SCART Cable DVI Cable Front 1. SOURCE
ملخص المحتوى في الصفحة رقم 13
2. PIP 3. MENU 4. 5. 6. 7. [ ] Power button 8. Remote control sensor 9. Power indicator 10. Speaker 1. SOURCE Press the SOURCE button to change the input signal source. Changing the source is allowed only in external devices that are connected to the monitor at the time. To switch Screen modes: [PC] → [DVI] → [TV] → [Ext.] → [AV] → [S-Video] → [Component] >>Click here to see an animation clip 2. PIP - Available in PC/DVI Mode In PC mode, turns on Video or TV screens in PIP
ملخص المحتوى في الصفحة رقم 14
Rear (The configuration at the back of the monitor may vary from product to product.) 1. POWER ! Power terminal Connect the power cord for your monitor to the POWER on the back of the monitor. This product may be used with 100 ~ 240VAC(+/- 10%). 2. DVI/PC IN 1. DVI(HDCP) : Connect the DVI cable to the DVI(HDCP) port on the back of your monitor. 2. RGB : Connect the signal cable to the RGB port on the back of your monitor. 3. AUDIO : PC sound terminal
ملخص المحتوى في الصفحة رقم 15
1. R - AUDIO - L : Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the R-AUDIO-L port of the monitor. 2. PR, PB,Y : Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the PR, PB,Y input ports using a component video cable (PR, PB,Y). 5. ANT IN ! Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the monitor. Make sure to use a TV antenna cable (sold separately) as the antenna cable. 6. ! The Kensington l
ملخص المحتوى في الصفحة رقم 16
1. POWER 2. Number button 3. -/--, +100 4. 5. MUTE 6. TTX/MIX 7. MENU 8. ENTER 9. 10. SOURCE 11. INFO 12. EXIT 13. Up-Down Left-Right buttons 14. AUTO 15. P.MODE, M/B (MagicBright™) 16. P.SIZE 17. STILL 18. PIP 19. S.MODE 20. DUAL/MTS 21. PRE-CH 22. SOURCE 23. SIZE 24. POSITION 25. MAGIC-CH 1. POWER Turns the monitor On/Off. 2. Number button Selects TV channels in the TV mode. Used to change channels when PIP is selected and the PIP Source is set to TV.
ملخص المحتوى في الصفحة رقم 17
9. In TV mode, selects TV channels. 10. SOURCE Press the 'SOURCE' button to change the input signal source. Changing the source is only allowed for external devices that are connected to the monitor at the time. 11. INFO Current picture information is displayed on the upper left corner of the screen. 12. EXIT Exits from the menu screen. 13. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 14. A
ملخص المحتوى في الصفحة رقم 18
25. MAGIC-CH MagicChannel enables you to watch only certain channels. This function is available only in Korea.
ملخص المحتوى في الصفحة رقم 19
Connecting the monitor 1.Connecting to a Computer 1. Connect the power cord for your monitor to the POWER on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Use appropriate connection for your computer. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the RGB port on the back of your monitor. [RGB] 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI(HDCP) port on th
ملخص المحتوى في الصفحة رقم 20
1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the RGB port on the Macintosh computer. [RGB] 2. Turn on the monitor and Macintosh. Connecting to Other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR or camcorder, or a DTV or TV without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. 1-1. Connecting AV Devices The monitor has AV conn
