ملخص المحتوى في الصفحة رقم 1
TABLE OF CONTENTS
Special notes on LCD monitors ................................................. .1
Information for your safety and comfort................................. .2
Unpacking .................................................................................. .5
Attaching/Removing the base....................................................6
Screen position adjustment ....................................................... .7
Connecting the power cord ..................................
ملخص المحتوى في الصفحة رقم 2
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as
ملخص المحتوى في الصفحة رقم 3
Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. CAUTION for accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet. Warnings • Do not use thi
ملخص المحتوى في الصفحة رقم 4
• the product was exposed to rain or water • the product has been dropped or the case has been damaged • the product exhibits a distinct change in performance, indicating a need for service • the product does not operate normally after following the operating instructions ----------------------------------------------------------------------------------------------------- Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls
ملخص المحتوى في الصفحة رقم 5
• install the external display, keyboard and mouse properly and within comfort able reach • if you view your monitor more than your documents, place the display at the center of your desk to minimize neck strain Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain
ملخص المحتوى في الصفحة رقم 6
B233HL LCD monitor P/N: MU.LSL00.001 2010 Quick Start Guide
ملخص المحتوى في الصفحة رقم 7
ATTACHING/REMOVING THE BASE Install: Align the base with the stand and push the base towards the top of the monitor, and then rotate the base clockwise until it stops. Tighten the screw clockwise. Remove: Reverse the steps to remove the base. EN-6
ملخص المحتوى في الصفحة رقم 8
SCREEN POSITION ADJUSTMENT In oder to optimize the best viewing position, you can adjust the height/tilt/ swivel of the monitor. · Height Adjustment After pressing the top of the monitor, push the lock button towards right, then you can adjust the height of the monitor. 110mm · Tilt Please see the illustration below for an example of the tilt range. EN-7
ملخص المحتوى في الصفحة رقم 9
· Swivel With the built-in pedestal, you can swivel the monitor for the most comfortable viewing angle. EN-8
ملخص المحتوى في الصفحة رقم 10
CONNECTING THE POWER CORD • Check first to make sure that the power cord you use is the correct type required for your area. • This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. No user-adjustment is required. • Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet. • For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V. • For unit using at 220/240 V AC (outs
ملخص المحتوى في الصفحة رقم 11
Power saving The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. LED State Light ON Blue Power Saving Amber Mode The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 3 seconds. DDC To make your installation easier, the monitor is able to Plug and Play with your system if you
ملخص المحتوى في الصفحة رقم 12
CONNECTOR PIN ASSIGNMENT 15-Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground EN-11
ملخص المحتوى في الصفحة رقم 13
24-Pin Color Display Signal Cable PIN Meaning PIN Meaning 1. TMDS Data2- 13. NC 2. TMDS Data2+ 14. +5V Power TMDS Data 2/4 GND(return for 3. 15. Shield +5V hsync.vsync) 4. NC 16. Hot Plug Detect 5. NC 17. TMDS Data0- 6. DDC Clock 18. TMDS Data0+ TMDS Data 0/5 7. DDC Data 19. Shield 8. NC 20. NC 9. TMDS Data1- 21. NC 10. TMDS Data1+ 22. TMDS Clock Shield TMDS Data 1/3 11. 23. TMDS Clock+ Shield 12. NC 24. DDC TMDS Clock- EN-12
ملخص المحتوى في الصفحة رقم 14
Standard Timing Table Mode Resolution 1 VGA 640x480 60 Hz 2 MAC 640x480 60.66 Hz 3 VESA 720x400 70 Hz 4 SVGA 800x600 56 Hz 5 SVGA 800x600 60 Hz 6 XGA 1024x768 60 Hz 7 XGA 1024x768 70 Hz 8 VESA 1152x864 75 Hz 9 SXGA 1280x1024 60 Hz 10 WXGA 1280x800 60 Hz 11 WXGA+ 1400x900 60 Hz 12 UXGA 1920x1080 60 Hz EN-13
ملخص المحتوى في الصفحة رقم 15
ملخص المحتوى في الصفحة رقم 16
USER CONTROLS 3 4 6 5 5 1 2 Front Panel Controls 1.Power Switch: To turn ON or OFF the power. 2.Power LED: Lights up to indicate the power is turned ON. 3.Empowering / Exit: 1) When OSD menu is in active status, this button will act as EXIT-KEY(EXIT OSD menu). 2) When OSD menu is in off status, press this button to select scenario mode. 4.Auto Adjust button / Exit: 1)When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). 2)When OSD menu is in off status, press this
ملخص المحتوى في الصفحة رقم 17
HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4. • When user press “MENU” button on front bezel A B A. Acer eColor Management If selected to “Acer eColor Management “ item, wil
ملخص المحتوى في الصفحة رقم 18
· ADJUSTING THE PICTURE The descriptions for function control LEDS A. Acer eColor Management Main Sub Sub Menu Menu Menu Description icon icon item User defined. Settings can be fine-tuned to N/A User mode suit any situation Adjusts th e setting s to reduce power N/A ECO mode consumption Standard Default Setting. Reflects native display N/A mode capability Grahpic N/A Enhances colors and emphasize fine detail mode Displays scenes in clearest detail. Pictures and Movie N/A photographs appear in v
ملخص المحتوى في الصفحة رقم 19
Main Sub Sub Menu Menu Menu Description Item Icon Icon Adjust the horizontal position. H. Position (available in Analog mode only) Adjust the vertical position. (available V. Position in Analog mode only) Set the colo r temperature to warm N/A Warm white. Set the color temperature to cool N/A Cool white. User /Red Adjusts Red/Green/Blue intensity. User /Green User /Blue N/A English N/A N/A Deutsch N/A Francais Multi-language selection. N/A Espanol N/A Italiano N/A N/A N/A Suomi N/A Nederlands
ملخص المحتوى في الصفحة رقم 20
Main Sub Sub Menu Menu Menu Description Item Icon Icon H. Position Adjust the horizontal position of the OSD. V. Position Adjust the vertical position of the OSD. OSD Timeout Adjust the OSD timeout. Select input signal from D-Sub or DVI-D N/A Input Source Select Wide mode setting for Full screen, N/A Wide Mode Aspect ratio N/A DDC/CI Turn ON/OFF DDC/CI support Show the resolution, H/V frequency andinput N/A Information port of current input timing. Clear each old status of Auto- N/A Reset confi
