ملخص المحتوى في الصفحة رقم 1
REJ10J1394-0200
H8SX/1651 Group PLQP0120LA-A
User System Interface Board
for E6000H Emulator
HS1651ECN61H User’s Manual
Renesas Microcomputer Development Environment System
H8SX Family / H8SX/1600 Series
HS1651ECN61HE
Rev.2.00
Revision Date: Sep. 08, 2008
ملخص المحتوى في الصفحة رقم 2
Rev. 2.00 Sep. 08, 2008 Page ii of vi REJ10J1394-0200
ملخص المحتوى في الصفحة رقم 3
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this do
ملخص المحتوى في الصفحة رقم 4
Rev. 2.00 Sep. 08, 2008 Page iv of vi REJ10J1394-0200
ملخص المحتوى في الصفحة رقم 5
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. � KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. User System Interface Board: Throughout this document, the term "user system interface board" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. • User system inte
ملخص المحتوى في الصفحة رقم 6
LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface boards determined to be defective in material and/or workmanship. User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole re
ملخص المحتوى في الصفحة رقم 7
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state. The Warranty is Void in the Following Cases: Renesas shall have no liability or legal responsibility for any problems caused by misuse, abuse, misapplication, neglect,
ملخص المحتوى في الصفحة رقم 8
SAFETY PAGE READ FIRST � READ this user's manual before using this user system interface board. � KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an immi
ملخص المحتوى في الصفحة رقم 9
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000H emulator and user system before connecting or disconnecting any CABLES or PARTS. 3. Always before
ملخص المحتوى في الصفحة رقم 10
Rev. 2.00 Sep. 08, 2008 Page VI of VI REJ10J1394-0200
ملخص المحتوى في الصفحة رقم 11
Preface The HS1651ECN61H is a user system interface board that connects a user system for the H8SX/1651 PQLP0120LA-A (former package: FP-120B) to the H8SX/1650 E6000H emulator (HS1650EPH60H).
ملخص المحتوى في الصفحة رقم 12
Contents Preface ......................................................................................................................i Section 1 Configuration...........................................................................................1 Section 2 Connection Procedures............................................................................3 2.1 Connecting the User System Interface Board to the User System........................................ 3 2.1.1 Installing the IC
ملخص المحتوى في الصفحة رقم 13
Section 1 Configuration Section 1 Configuration Figure 1 and table 1 show the external appearance and components, respectively, of the user system interface board for the PLQP0120LA-A package. Please make sure you have all of these components after you have unpacked the box. Evaluation chip board Spacer Screws (M2.0 × 10 mm) (for fastening cable head) Screws (M2.0 x 6 mm) Board Socket cover IC socket User system Figure 1 User System Interface Board for the H8SX/1651 Group PLQP0120L
ملخص المحتوى في الصفحة رقم 14
Section 1 Configuration CAUTION Use an NQPACK120SE-ND socket and an HQPACK120SE cover (manufactured by Tokyo Eletech Corporation) for the PLQP0120LA-A-packaged IC socket on the user system. Table 1 HS1651ECN61H Components No. Component Quantity Remarks 1 Board 1 2 IC socket 1 For the PLQP0120LA-A package 3 Socket cover 1 For installing an PLQP0120LA-A packaged MCU 4 Screw (M2.0 x 10 mm) 4 For fastening cable head 5 Screw (M2.0 x 6 mm) 4 For installing an PLQP0120LA-A packaged MCU
ملخص المحتوى في الصفحة رقم 15
Section 2 Connection Procedures Section 2 Connection Procedures 2.1 Connecting the User System Interface Board to the User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecting the two, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSON
ملخص المحتوى في الصفحة رقم 16
Section 2 Connection Procedures Use the guide pins provided with the product to determine where to install the IC socket, as shown in figure 2. Pin 1 Guide pins 4 projections to apply IC socket epoxy resin adhesive to (NQPACK120SE-ND manufactured by Tokyo Eletech Corporation) Bottom view of IC socket User system Figure 2 Correctly Placing the IC Socket 2.1.2 Soldering the IC Socket After fastening, solder the IC socket for an PLQP0120LA-A package to the user system. CAUTION Be
ملخص المحتوى في الصفحة رقم 17
Section 2 Connection Procedures 2.1.3 Installing the IC Socket CAUTION Check the location of pin 1 before inserting. After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket connector, align the guide pins on the IC socket connector with the guide holes on the user system interface board, and insert the IC socket connector into the IC socket (figure 3). 2.1.4 Fastening the Cable Head CAUTION 1. Use a screwdriver whose head matches the screw
ملخص المحتوى في الصفحة رقم 18
Section 2 Connection Procedures Screws (M2.0 x 10 mm) Board IC socket (NQPACK120SE-ND Pin 1 manufactured by Tokyo Eletech Corporation) User system Figure 3 Connecting the User System Interface Board to the User System Rev. 2.00 Sep. 08, 2008 Page 6 of 20 REJ10J1394-0200
ملخص المحتوى في الصفحة رقم 19
Section 2 Connection Procedures 2.2 Exchanging the Spacers of the Evaluation Chip Board After connecting the user system interface board to the user system, be careful not to apply load to the user system. Exchange the spacers (2.6MP × 10 mm) for the evaluation chip board with the spacers (2.6MP × 25 mm) provided with the user system interface board. Evaluation chip board Spacer (2.6MP × 25 mm) Figure 4 Exchanging the Spacers Rev. 2.00 Sep. 08, 2008 Page 7 of 20
ملخص المحتوى في الصفحة رقم 20
Section 2 Connection Procedures 2.3 Connecting the User System Interface Board to the Evaluation Chip Board WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected or removed. Before connecti
