ملخص المحتوى في الصفحة رقم 1
REJ10B0198-0100
H8/36912, H8/36902 Group FP-32A
User System Interface Cable
HS36902ECH61H User’s Manual
Renesas Microcomputer Development Environment System
H8 Family / H8/300H Tiny Series
HS36902ECH61HE
Rev.1.00
Revision Date: Jun. 22, 2005
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammabl
ملخص المحتوى في الصفحة رقم 4
ملخص المحتوى في الصفحة رقم 5
IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. User System Interface Cable: Throughout this document, the term "user system interface cable" shall be defined as the following product produced only by Renesas Technology Corp. excluding all subsidiary products. • User system inte
ملخص المحتوى في الصفحة رقم 6
LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free from defects in material and/or workmanship. Renesas will repair or replace any user system interface cables determined to be defective in material and/or workmanship. User system interface cables are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole re
ملخص المحتوى في الصفحة رقم 7
State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state. The Warranty is Void in the Following Cases: Renesas shall have no liability or legal responsibility for any problems caused by misuse, abuse, misapplication, neglect,
ملخص المحتوى في الصفحة رقم 8
SAFETY PAGE READ FIRST READ this user's manual before using this user system interface cable. KEEP the user's manual handy for future reference. Do not attempt to use the user system interface cable until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an immi
ملخص المحتوى في الصفحة رقم 9
WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance. 2. Always switch OFF the E6000 emulator and user system before connecting or disconnecting any CABLES or PARTS. 3. Always before c
ملخص المحتوى في الصفحة رقم 10
VI
ملخص المحتوى في الصفحة رقم 11
Preface Thank you for purchasing this user system interface cable (HS36902ECH61H) for the Renesas’ original microcomputer H8/36912, H8/36902 group. The HS36902ECH61H is a user system interface cable that connects an H8/36912, H8/36902 group E6000 emulator (HS3664EPI61H or HS3664EPI62H; hereinafter referred to as the emulator) to the IC socket for an FP-32A package for the H8/36912, H8/36902 group MCU on the user system. i
ملخص المحتوى في الصفحة رقم 12
Contents Section 1 Configuration.....................................................................................1 Section 2 Connection Procedures......................................................................3 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 3 2.2 Connecting User System Interface Cable to User System ................................................ 5 2.2.1 Installing IC Socket ..........................
ملخص المحتوى في الصفحة رقم 13
Section 1 Configuration CAUTION Use an NQPACK032SA socket (manufactured by Tokyo Eletech Corporation) for the FP-32A package IC socket on the user system. Figure 1 shows the configuration of the HS36902ECH61H user system interface cable for the FP-32A package. To emulator station CTS screws (M3 x 6 mm) for fastening the emulator station Cable body Screws (M2 x 10 mm) (for fastening cable head) Screws (M2 x 6 mm) Cable head Socket cover IC socket User system Figure 1 HS36902EC
ملخص المحتوى في الصفحة رقم 14
Table 1 lists the HS36902ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS36902ECH61H Components No. Component Quantity Remarks 1 Cable body 1 Coaxial cable 2 Cable head 1 3 IC socket 1 For the FP-32A package 4 Socket cover 1 For installing an FP-32A-packaged MCU 5 Screws (M2 x 10 mm) 4 For fastening cable head 6 Screws (M2 x 6 mm) 4 For installing an FP-32A-packaged MCU 7 CTS screws (M3 x 6 mm) 2 For fastening the emulator station 8
ملخص المحتوى في الصفحة رقم 15
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before conn
ملخص المحتوى في الصفحة رقم 16
Emulator station Cable body connector CTS screws (M3 x 6 mm) User system interface cable Figure 2 Connecting User System Interface Cable to Emulator Station 4 E6000
ملخص المحتوى في الصفحة رقم 17
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. To connect the cab
ملخص المحتوى في الصفحة رقم 18
2.2.1 Installing IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. CAUTION After confirming the location of pin 1 on the IC socket, apply epoxy resin adhesive to the end of the four projections at the bottom of the IC socket, and fasten it to the user system. Use the guide pins provided to determine where to install the IC socket, as shown in figure 3. Guide pins Pin 1 4 projections to apply epoxy resin adhesive to IC s
ملخص المحتوى في الصفحة رقم 19
CAUTION Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly more solder than the MCU.) 2.2.2 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-32A package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in figure 4. 2.2.3 Fa
ملخص المحتوى في الصفحة رقم 20
Fasten the user system interface cable head to the IC socket for an FP-32A package on the user system with the two screws (M2 x 10 mm) provided. Each screw should be tightened a little at a time, alternating between screws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components. Screws (M2 x 10 mm) Cable head Pin 1 IC socket (NQPACK032SA ma
