ملخص المحتوى في الصفحة رقم 1
Jiva TP/LT – 5815
Touch / LCD POS Terminal
w/ Slim or Universal Base
User’s Manual
Rev.: B2
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection ag
ملخص المحتوى في الصفحة رقم 2
ALERT TO OUR HONORABLE CUSTOMERS: l Please always read thoroughly all the instructions and documents delivered with the product before you do anything about it. Don’t take any premature action before you have a full understanding of the consequences. l This product contains inside a Lithium battery and maybe also a sealed type Lead acid battery if the UPS battery option is ordered. Please always follow local environmental protection laws / regulations for disposal of used batteries and
ملخص المحتوى في الصفحة رقم 3
INTRODUCTION PRODUCT PICTURES Front Views 1 1 2 3 2 4 4 5 7 6 Slim Base Models Universal Base Models 9 8 8 9 10 10 7 Slim Base Models Universal Base Models 5 Side Views 11 11 12 12 10 10 5 7 Universal Base Models Slim Base Models 1 1 12 13 13 7 5 Slim Base Models Universal Base Models Part 3
ملخص المحتوى في الصفحة رقم 4
Rear Views 1 11 1 12 7 5 8 14 10 10 14 15 16 16 Slim Base Models Universal Base Models 16 Bottom Views 16 17 20 20 21 21 18 19 19 Slim Base 3.5” HDD Universal Base 3.5” HDD 17 16 19 22 19 23 21 21 20 24 20 Slim Base 2.5” HDD Universal Base 2.5” HDD PARTS IDENTIFICATION 1. Main unit 2. Touch panel / LCD panel 3. Optional side mount kit 4. Power status indicator 5. Universal base stand 6. Optional CDROM drive 7. Slim
ملخص المحتوى في الصفحة رقم 5
11. Optional rear top mount kit PD-302 12. Lock / release button for main unit detach 13. Power switch 14. Rear connect cover 15. Power connector hole 16. Cable exit nd 17. 2 cable exit 18. Auxiliary cable exit 19. Rubber feet 20. Bottom plate 21. Bottom plate fixing screw 22. 2.5” HDD window 23. 2.5” HDD bracket cover 24. 2.5” HDD bracket fixing screw PRODUCT FEATURES Standard Features: CPU: C3 - 1.0 GHz. An advanced slim or universal base design. The slim base models nd sup
ملخص المحتوى في الصفحة رقم 6
5. 2 USB ports 6. one LAN port 10/100 base T Ethernet 7. one external VGA monitor port 8. one IDE connector and HDD power connector for HDD in base 9. one 4 pin lock type DC 12 V power input connector 10. one UPS battery connector 11. one CR port for control over 2 cash drawers max. 12. audio ports (1 Microphone input and 2 optional slim type speakers) Touch control functions: left/right button, double click, drag & draw Dual display support (per OS capability) VGA memory size shared
ملخص المحتوى في الصفحة رقم 7
i) IDE interface internal slim type CD ROM drive or COMBO in base for universal base models j) UPS battery in base k) Preload OS l) 2 in 1 cash drawer control cable (CCBLA-238) m) Wall mount kit: WB-6000, WB-6300, WB-6600, WB-6800 Part 7
ملخص المحتوى في الصفحة رقم 8
INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded. Failure to do the above will void the product warranty! OPENING CABLE COVER Please follow steps A to C sequent
ملخص المحتوى في الصفحة رقم 9
SEPARATING MAIN UNIT In order to settle the touch terminal properly in a point of service system, all the cable connections have to be routed through its base, either slim or universal. Therefore, please observe the procedures from A to C below to separate the main unit from both slim and universal base stand assembly after all cables in cable cover disconnected. C Step A: Prepare a soft clean flat surface, such B as a piece of cloth on the desk to seat the front surface of ma
ملخص المحتوى في الصفحة رقم 10
model will look like the right picture above. Both with numbered items listed as below. However, there could be some variation to the contents inside depending on what option items actually installed. When the HDD installed is the 2.5” type, the HDD mounting bracket, the metal base chassis and the bottom plate will also look different. 1. Cable Exit For External Connections 2. Cable Tie 3. CD-ROM Bracket For Universal Base 4. Cable Passage To Main Unit For Desktop Mount Application 5.
ملخص المحتوى في الصفحة رقم 11
as in left picture. Put the battery in at the other end first and remount the bracket with its tongue matching under a bridge in the wall of base box from the right as arrowed in above left picture then apply the fixing screw. Please pay particular attention to the environment requirements for UPS battery in next chapter “USING THE TOUCH POS”. WALL MOUNTING WB-6000 WB-6300 WB-6600 WB-6800 Select a flat surface on wall of adequate strength and with proper ventilation and spa
ملخص المحتوى في الصفحة رقم 12
backpack into the cable cover area of main unit. The area required for wall mount application is determined by the main unit dimensions and is 376 mm in width and 315 mm in height. BASE MOUNT UPGRADE KIT On rear edge of the stand assembly for desktop mount application, there is a rear connect cover. Either a 2nd LCD display panel option LM- 6201 or LM-6301 or a customer display option PD- 2501 or PD-2602 or PD-305 can be installed here after removing this cover. Please note that there
ملخص المحتوى في الصفحة رقم 13
nd 15” 2 LCD Panel Please follow the installation instruction that come alone with the 15” nd 2 LCD monitor LM-6301 to mount the interface bracket kit onto the LCD panel. Fit the interface bracket the same way as joint base of LM-6201 to the rear connect opening and fix with 2 screws with washers. Route the VGA through the cable exit of the base stand to the main unit. Connect the attached power adaptor for its power source. ROUTING THE CABLES Place all the cables required for connecti
ملخص المحتوى في الصفحة رقم 14
WIRELESS PRINTER To access the Posiflex wireless thermal printer PP7700 in Windows environment except Win CE, a wireless Dongle DG2000 for this printer must be separately purchased and installed to one of the serial COM ports in Jiva system. Please enable the + 5 V DC power support for this COM port. Hook the Dongle to either top corner of the Jiva TP / LT system as in the right picture. DESKTOP MOUNTING Matching Holes Matching Pegs Round Part Slot Part Removal Hollow
ملخص المحتوى في الصفحة رقم 15
such as the external VGA, LPT and COM connector be screwed into place once seated. If the COM1 port must be used, the COM1 terminator that occupies the COM1 port must be removed and safely preserved for future use. However, when using the COM1 port, it is advisable to use devices that provide proper hardware handshaking signals in order to keep other embedded system features. A serial mouse is one example of a device that does not support handshaking. Adjust the slack of each cable and
ملخص المحتوى في الصفحة رقم 16
USING THE TOUCH TERMINAL APPLICATION ENVIRONMENT It is very important to check the following operational guidelines: Ventilation This terminal must NOT be used in an environment with restricted ventilation. There must be at least 25 mm air clearance around any ventilation holes with a free flow of air around the unit at ALL times for the installation. Operating Environment The equipment must not be operated or stored in extremes of both temperature and humidity/moisture. (Operating ra
ملخص المحتوى في الصفحة رقم 17
Power Supply The operating voltage range of the power adaptor should cover the local power supply for proper operation. The power cable, the power outlet and any power fusing arrangements must conform to local safety regulations. Please never do any connection / disconnection when system is still powered on. Please always keep the external power adaptor in a free air circulation. POWER ON/OFF There must always be at least 10 seconds waiting before switching on again once the system is
ملخص المحتوى في الصفحة رقم 18
make sure that the software application has the ability to power off the machine. In preloaded Windows, “Posiflex Power Switch Manager” in “Posiflex Tools” in the Program Files helps managing these functions. Software Support Features The Jiva series provides a software power off for application program maneuvers as mentioned above. The Jiva also provides a specific means for the software to detect if the system is working on external or UPS battery power. So the compatible software app
ملخص المحتوى في الصفحة رقم 19
supply the required power through the VGA connector for LM-6212. Do not connect other monitor to this port before the power in this port is disabled. CUSTOMER DISPLAY Please follow the instructions on the manual that comes along with the customer display PD-2501 or PD-2602 when it is installed. SERIAL PORTS The serial ports in Jiva system can supply a +5 V DC through pin 9 after proper jumper setting change. However, they are set to standard RS232 serial ports as status at delivery. C
ملخص المحتوى في الصفحة رقم 20
TOUCH PANEL All paragraphs below are applicable for models with touch panel only. The user of those models without touch panel can ignore them and consider this user’s manual ends here. Mouse Emulation The touch panel in Jiva system uses USB interface as standard. Only the optional InfraRed type touch panel uses RS232 interface. When the touch driver is properly installed, this touch panel works exactly like a standard mouse except when the system is running under safe mode. The mouse
