ملخص المحتوى في الصفحة رقم 1
USER’S
MANUAL
EB-471LF
®
ULV Celeron M
3.5” Embedded Card
With VGA/ SOUND/ LAN
EB-471LF M1
ملخص المحتوى في الصفحة رقم 2
Copyright Notice EB-471LF Celeron® M 3.5” Embedded Card With VGA /Sound/LAN OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist both Embedded Computer manufacturers and end users in installing and setting up the system. The information contained in this document is subject to change without any notice. This manual is copyrighted in April, 2006. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, inc
ملخص المحتوى في الصفحة رقم 3
Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer
ملخص المحتوى في الصفحة رقم 4
Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1-1 About This Manual ........................................................ 1-2 1-2 System Specification ...................................................... 1-3 1-3 Safety Precautions ......................................................... 1-5 CHAPTER 2 HARDWARE CONFIGURATION 2-1 Jumper & Connector Quick Reference Table ................ 2-2 2-2 Component Locations ..................
ملخص المحتوى في الصفحة رقم 5
Contents CHAPTER 3 SOFTWARE UTILITIES 3-1 Introduction …………..........................................…....... 3-2 3-2 VGA Driver Utility ……………………………….…… 3-2 3-3 Flash BIOS Update ..............................................…....... 3-4 3-4 LAN Driver Utility …...........................................…...... 3-6 3-5 Sound Driver Utility …………………………………… 3-7 3-6 Intel Chipset Software Installation Utility …..……..….. 3-8 3-7 USB2.0 S
ملخص المحتوى في الصفحة رقم 6
CHAPTER 1 INTRODUCTION This chapter gives you the information for EB-471LF. It also outlines the System specification. Section includes: About This Manual System Specifications Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start. Page:1-1
ملخص المحتوى في الصفحة رقم 7
Chapter 1 Introduction 1-1. ABOUT THIS MANUAL Thank you for purchasing our EB-471LF Celeron® M3.5” Embedded Card enhanced with VGA /Sound/ LAN, which is fully PC / AT compatible. EB- 471LF provides faster processing speed, greater expandability and can handle more task than before. This manual is designed to assist you how to install and set up the system. It contains four chapters. The user can apply this manual for configuration according to the following chapters : Chapte
ملخص المحتوى في الصفحة رقم 8
Chapter 1 Introduction 1-2. SYSTEM SPECIFICATION CPU : Intel® Celeron® M processor Ultra Low Voltage without L2 cache onboard Available at 600MHz System bus frequency at 400MHz Auto detect voltage regulator SYSTEM CHIPSET : Intel® 852GM chipset MEMORY : Supports up to 1 GB DDR SDRAM. One 200-pin DDR SO-DIMM sockets on board CACHE : Built-in CPU REAL-TIME CLOCK / CALENDAR : 256-byte battery backed CMOS RAM. Hardware implementation to indicate century roll
ملخص المحتوى في الصفحة رقم 9
Chapter 1 Introduction DISPLAY : Built in Intel 852GM, support CRT, LCD. IDE INTERFACE : One IDE ports support up to two IDE devices. Supports UDMA 33/66/100. LAN INTERFACE : Intel® 82562ET 10/100 Base-T SOUND: AC '97 Codec. Reatel ALC202A. Fully Compliant AC '97 Analog I/O Component SERIAL PORT : Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte FIFOs. COM1 for RS232; COM2 for RS232/422/485. HARDWARE MONITORING FUNCTION : Monito
ملخص المحتوى في الصفحة رقم 10
Chapter 1 Introduction OPERATING TEMPERATURE : 0 to 60 °C (32 °F to 140 °F) INPUT POWER REQUIREMENT : AT power: +5V, +12V Only +5V: +5V only provide power for SBC, It does not have enough power to support expansion card. BOARD DIMENSION : 102mm x 145mm (4.02” x 5.71”) BOARD NET WEIGHT : 290 grams (0.64 lb) 1-3. SAFETY PRECAUTIONS Follow the messages below to avoid your systems from damage: 1. Avoid your system from static electricity on all occasions.
ملخص المحتوى في الصفحة رقم 11
CHAPTER HARDWARE 2 CONFIGURATION ** QUICK START ** Helpful information describes the jumper & connector settings, and component locations. Section includes: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector’s Pin Assignments Page 2-1
ملخص المحتوى في الصفحة رقم 12
Chapter 2 Hardware Configuration 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM1, COM2 COM Port Connector ....................…..................……… RS232/422/485 (COM2) Selection .....................……… JP1 DIN1 Keyboard/Mouse Connector ..........…………......…… JPANEL1(7,8) Reset Connector .........................…....................………. JPANEL1(2,4) Hard Disk Drive LED Connector .......................………. JPANEL1(5,6) External Speaker Connector ....…................
ملخص المحتوى في الصفحة رقم 13
Chapter 2 Hardware Configuration 2-2. COMPONENT LOCATIONS VGA1 LVDS1 DIN1 11 15 1 1 610 1 5 J2 2 30 JP5 LED1 LAN1 JP4 BZ1 AC97 INTEL JPANEL1 COM2 2 1 1 COM1 JP2 1 JTV1 Celeron-M 2 1 2 2 JSFAN1 JP1 J1 PW1 IDE1 USB1 44 43 EB-471LF Connector, Jumper and Component locations Page: 2-3 EB-471LF USER ′S MANUAL
ملخص المحتوى في الصفحة رقم 14
Chapter 2 Hardware Configuration 2-3. HOW TO SET THE JUMPERS You can configure your board by setting jumpers. Jumper is consists of two or three metal pins with a plastic base mounted on the card, and by using a small plastic "cap", Also known as the jumper cap (with a metal contact inside), you are able to connect the pins. So you can set-up your hardware configuration by "open" or "close" pins. The jumper can be combined into sets that called jumper blocks. When the jump
ملخص المحتوى في الصفحة رقم 15
Chapter 2 Hardware Configuration JUMPER DIAGRAMS Jumper Cap looks like this 2 pin Jumper looks like this 3 pin Jumper looks like this Jumper Block looks like this JUMPER SETTINGS 2 pin Jumper close(enabled) Looks like this 1 1 3 pin Jumper 2-3 pin close(enabled) Looks like this 1 1 Jumper Block 1-2 pin close(enabled) Looks like this 12 1 2 Page: 2-5 EB-471LF USER ′S MANUAL
ملخص المحتوى في الصفحة رقم 16
Chapter 2 Hardware Configuration 2-4. COM PORT CONNECTOR COM1 : COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 DCD1 2 RX1 3 TX1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI1 10 NC COM2 : COM2 Connector The COM2 is selectable as RS-232/422/485. The pin assignment is as follows : ASSIGNMENT PIN RS-232 RS-422 RS-485 1 DCD2 TX- TX- 2 RX2 TX+ TX+ 3 TX2 RX+ RX+ 4 DTR2 RX- RX- 5 GND GND GND 6 DSR2 RTS- NC 7 RTS2 R
ملخص المحتوى في الصفحة رقم 17
Chapter 2 Hardware Configuration 2-5. RS232/422/485 (COM2) SELECTION JP1 : RS-232/422/485 (COM2) Selection This connector is used to set the COM2 function. The jumper settings are as follows : COM 2 Jumper Settings Jumper Function (pin closed) Illustrations RS-232 Open RS-422 1-2, 3-4, 9-10 RS-485 1-2, 5-6, 7-8 *** Manufactory default --- RS-232. Page: 2-7 EB-471LF USER ′S MANUAL
ملخص المحتوى في الصفحة رقم 18
Chapter 2 Hardware Configuration 2-6. KEYBOARD/MOUSE CONNECTOR DIN1 : Keyboard/Mouse Connector The pin assignments are as follows : PIN ASSIGNMENT 1 KB_DATA 2 MS_DATA 3 GND 5 K/B_VCC 6 KB_CLK 8 MS_CLK 2-7. RESET CONNECTOR JPANEL1 (7,8) : Reset Connector. The pin assignment is as follows : PIN ASSIGNMENT 7 GND 8 RST_SW 2-8. HARD DISK DRIVE LED CONNECTOR JPANEL (2, 4) : Hard Disk Drive LED Connector The pin assignment is as follows : PIN ASSIGNME
ملخص المحتوى في الصفحة رقم 19
Chapter 2 Hardware Configuration 2-9. EXTERNAL SPEAKER CONNECTOR JPANEL1 (5, 6) : External Speaker Connector The pin assignment is as follows : PIN ASSIGNMENT 5 SPK1 6 SPK_VCC 2-10. POWER LED CONNECTOR JPANEL1 (1, 3) : Power LED Connector The pin assignment is as follows: PIN ASSIGNMENT 1 VCC_R 3 GND 2-11. IRDA CONNECTOR JIRDA1: IrDA (Infrared) Connector The pin assignments are as follows: PIN ASSIGNMENT 1 +5V 2 NC 3 IRRX 4 GND 5 IRTX P
ملخص المحتوى في الصفحة رقم 20
Chapter 2 Hardware Configuration 2-12. SYSTEM FAN CONNECTOR JSFAN1 : System Fan connector The pin assignment is as follows: PIN ASSIGNMENT 1 GND 2 +12V 3 FAN0 2-13. VGA CONNECTOR VGA1 : VGA CRT Connector The pin assignments are as follows: PIN ASSIGNMENT 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VGA_P5V 10 GND 11 NC 12 VGA_5VDDCDA 13 VGA_HSYNC_5V 14 VGA_VSYNC_5V 15 VGA_5VDDCLK 16 NC Page: 2-10 EB-471LF USER ′S MANUAL
