National Instruments 8252 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

NI PCI-8252 Quick Start Guide
The NI PCI-8252 is a highly flexible IEEE 1394a interface device for PCI.
The following sections describe how to get started using the NI PCI-8252.
Installing the NI PCI-8252
The following section contains a list of necessary and optional items for
acquiring images with the NI PCI-8252. This section also explains how to
unpack, configure, and install the NI PCI-8252.
What You Need to Get Started
You need the following items to set up and use the NI PCI-8252:
❑ NI

ملخص المحتوى في الصفحة رقم 2

Safety Information Caution The following paragraphs contain important safety information you must follow when installing and operating the device. Do not operate the device in a manner not specified in the documentation. Misuse of the device may result in a hazard and may compromise the safety protection built into the device. If the device is damaged, turn it off and do not use it until service-trained personnel can check its safety. If necessary, return the device to National Instruments

ملخص المحتوى في الصفحة رقم 3

You must insulate signal connections for the maximum voltage for which the device is rated. Do not exceed the maximum ratings for the device. Remove power from signal lines before connection to or disconnection from the device. Caution National Instruments measurement products may be classified as either Measurement Category I or II. Operate products at or below the Measurement Category level specified in the hardware specifications. 1 Measurement Category : Measurement circuits are subjec

ملخص المحتوى في الصفحة رقم 4

 Measurement Category IV is for measurements performed at the primary electrical supply installation (<1,000 V). Examples include electricity meters and measurements on primary overcurrent protection devices and on ripple control units. Unpacking The NI PCI-8252 ships in an antistatic package to prevent electrostatic discharge from damaging device components. To avoid such damage in handling the device, take the following precautions:  Ground yourself via a grounding strap or by holding a

ملخص المحتوى في الصفحة رقم 5

5. Touch a metal part on the computer case to discharge any static electricity that might be on your clothes or body before handling the NI PCI-8252. Static electricity can damage the device. 6. Remove the NI PCI-8252 from the antistatic package and gently rock the NI PCI-8252 into the slot. The connection may be tight, but do not force the device into place. Note Check that the bracket of the NI PCI-8252 lines up with the hole in the back panel rail of the computer chassis. 7. Unless your

ملخص المحتوى في الصفحة رقم 6

Connector 1394 ........................................................Female, 6 pin (3) PCI ..........................................................32-bit, Universal Signaling PCI V ....................................................Universal, 33 MHz io 1394 ........................................................IEEE 1394a-1995 S100, S200, S400 transfer rates, OHCI v1.1 software interface. Actual 1394 transfer rates are system dependent. Power Consumption Typical .......................

ملخص المحتوى في الصفحة رقم 7

Storage Environment Ambient temperature range.................... –20 °C to 60 °C Storage relative humidity ....................... 20% to 95%, noncondensing Safety This product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use:  IEC 61010-1, EN 61010-1  UL 61010-1  CAN/CSA-C22.2 No. 61010-1 Note For UL and other safety certifications, refer to the product label, or visit ni.com/certification, sear

ملخص المحتوى في الصفحة رقم 8

Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity. This system affords the user protection for electro