ملخص المحتوى في الصفحة رقم 1
I-45C
I-45CV
Motherboard
Intel Socket 775
Installation Guide
ملخص المحتوى في الصفحة رقم 2
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental
ملخص المحتوى في الصفحة رقم 3
环保使用期限标识说明 有毒有害物质含有表 环 保使用期 限标识 是根据< 电子 产品中有毒有害物质或元素的名称及含量 信 息产品污 染控制 管理办法> 以 有毒有害物质或元素 及< 电子 信息产品 污染控制 标识 部件名称 六价铬 多溴联苯 多溴二苯 要求>(SJ/T11364-2006) ，< 电子 铅(Pb) 汞(Hg) 镉(Cd) 醚(PBDE) (Cr(VI)) (PBB) 信 息产品环 保使用 期限通则> 制 定的 ， 适用于 中国 境内销售 的电子 PCB 板 ○ ○ ○ ○ ○ ○ 信息产品的标识。 结构件 ○ ○ ○ ○ ○ ○ 只要按照安全及使用说明内容在 芯片及其他主 × ○ ○ ○ ○ ○ 正常使用 电子信 息产品情 况下 、 从 动件 生产月期 算起 ， 在 此期限内 产品中 连接器 × ○ ○ ○ ○ ○ 含有的有毒有害物质不致发生外 被动电子元器 泄或突变 、 不 致对 环境造成 严重污 × ○ ○ ○ ○ ○ 件 染或对其人身、财产造成严重损害。产品正常使用后，要废弃在环保使 用 年限内或者刚到年限的产品，请根据国家标准采取适
ملخص المحتوى في الصفحة رقم 4
Contents 1. Hardware Setup ................................................ 1 2. BIOS Setup ...................................................... 13 1.1 Specifications .............................................................1 3. Driver & Utility ................................................ 14 1.2 Choosing a Computer Chassis......................................2 4. Appendix ......................................................... 15 1.3 Installing Motherboard..................
ملخص المحتوى في الصفحة رقم 5
Serial ATA 1. Hardware Setup • 4x SATA 3.0Gb/s 1.1 Specifications Expansion Slots • 1x PCI-E X16 slot CPU • 1x PCI-E X1 slot • LGA775 socket for Intel Core 2 Duo / Pentium Dual-Core / 1 Pentium D / Pentium 4 / Celeron D Processor with 1333* / 1066 / • 2x PCI slots 800 / 533MHz FSB. 1 Internal I/O Connectors * The FSB1333 CPU will operate in over-clocking mode. Under this situation, the PCIE frequency will also be over-clocked to 115MHz. • 1x Floppy port • 1x Ultra ATA 100 IDE co
ملخص المحتوى في الصفحة رقم 6
with slots. After the board has been positioned, check to make sure 1.2 Choosing a Computer Chassis everything is OK before putting the chassis back on. • Choose a chassis big enough to install this motherboard. ※ Always power off the computer and unplug the AC power cord • As some features for this motherboard are implemented by before adding or removing any peripheral or component. Failing to cabling connectors on the motherboard to indicators and switches so may cause severe damage
ملخص المحتوى في الصفحة رقم 7
1.4 Checking Jumper Settings For a 2-pin jumper, plug the jumper cap on both pins will make it CLOSE (SHORT). Remove the jumper cap, or plug it on either pin (reserved for future use) will leave it at OPEN position. SHORT OPEN OPEN For a 3-pin jumper, pin 1~2 or pin 2~3 can be shorted by plugging the jumper cap in. • Pin-1 and pin-2 shorted (Default): Normal operation. • Pin-2 and pin-3 shorted: Clear CMOS memory. To clear the CMOS memory and load in the default values: 1.
ملخص المحتوى في الصفحة رقم 8
or “CMOS checksum error” displays on monitor, this backup battery 1.5 Connecting Chassis Components is no longer functional and has to be renewed. 1.5.1 ATX Power Connectors These connectors provide the connection from an ATX power supply. As the plugs from the power supply fit in only one orientation, find the correct one and push firmly down into these connectors. To renew the backup battery: 1. Power off the system and disconnect with AC power source. 2. Remove the exhausted
ملخص المحتوى في الصفحة رقم 9
• PLED (Pin 16, 18, 20): 1.5.2 Front Panel Switches and Indicators Headers Connects to the Power LED cable of chassis front panel. This header is used for connecting switches and LED indicators on the chassis front panel. 1.5.3 FAN Power Connectors Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarity for the LED These connectors each provide power to the cooling fans installed in connection. Please pay attent
ملخص المحتوى في الصفحة رقم 10
1.6 Installing Hardware 2. Use your right-thumb to raise the load plate. Lift it up to fully open ※ DO NOT scratch the motherboard when installing hardware. An position. accidental scratch of a tiny surface-mount component may seriously damage the motherboard. ※ In order to protect the contact pins, please pay attention to these notices: 1. A maximum 20 cycles of CPU installation is recommended. 2. Never touch the contact pins with fingers or any object. 3. Always put on the ca
ملخص المحتوى في الصفحة رقم 11
5. Use your left hand to 8. Place the heatsink and hold the load plate, and fan assembly onto the use your right thumb to socket. Align the four peel the cap off. fasteners toward the four mounting holes on ※ The cap plays an the motherboard. important role in protecting contact pins. In order to prevent bent pin, PUT ON the cap after operation or testing. 6. Lower the plate onto the 9. Press each of the four fasteners down into the CPU package. Engage the load lever while mou
ملخص المحتوى في الصفحة رقم 12
1.6.2 DDR2 Memory Slots To install system memory: 1. Power off the computer and unplug the AC power cord before installing or removing memory modules. 2. Locate the DIMM slot on the board. 3. Hold two edges of the DIMM module carefully, keep away from • Install DIMMs with the same CAS latency. To reach the optimum touching its connectors. compatibility, obtain memory modules from the same vendor. 4. Align the notch key on the module with the rib on the slot. ※ Usually there i
ملخص المحتوى في الصفحة رقم 13
1.7.2 Serial ATA Connectors 1.7 Connecting Peripheral Devices Each SATA connector serves as one single channel to connect one SATA device by SATA cable. 1.7.1 Floppy and IDE Disk Drive Connectors To connect SATA device: Connect the single end at the longer length of ribbon cable to the FDD on the board, the two connectors on the other end to the floppy disk 1. Attach either end of the signal cable to the SATA connector on drives connector. Generally you need only one flop
ملخص المحتوى في الصفحة رقم 14
1.7.3 Additional USB 2.0 Port Headers 1.7.4 Internal Audio Connectors Each header supports 2x additional USB 2.0 ports by connecting This connector connects to the audio output of internal CD-ROM drive bracket or cable to the rear I/O panel or the front-mounted USB ports or add-on card. of your chassis. Pin Pin Assignment Pin Pin Assignment 1 VCC 2 VCC 3 Data0 - 4 Data1 - 5 Data0 + 6 Data1 + 7 Ground 8 Ground 10 NC ※ Make sure the connecting cable bears the same pin assi
ملخص المحتوى في الصفحة رقم 15
※ Please do not connect the “Ground” cable or “USB VCC” cable from 1.7.5 Front Panel Audio Connection Header the front panel module to the Pin 4 “AVCC” of this header. This header provides the front panel connection for HD (High Definition) Audio, yet for AC’97 Audio CODEC connection, you must carefully check Driver Configuration for AC’97 audio connection: the pin assignment before connecting from the front panel module. An The audio driver is originally configured to support HD Audio.
ملخص المحتوى في الصفحة رقم 16
1.8 PCI and PCI Express X16, X1 Slots 1.9 Connecting Rear Panel I/O Devices Install PCI Express X16 graphics card into slot “PCIEXP1”. The rear I/O part of this motherboard provides the following I/O ports: Install PCI Express X1 cards into slot “PCIE1”. Install PCI cards into slots “PCI1” and/or “PCI2”. • Mouse: Connects to PS/2 mouse. • Keyboard: Connects to PS/2 keyboard. • LPT1: Connects to printer or other devices that support this communication protocol. • COM1: Connects to e
ملخص المحتوى في الصفحة رقم 17
2. BIOS Setup This motherboard provides a programmable EEPROM so that you can Phoenix – AwardBIOS CMOS Setup Utility update the BIOS utility. The BIOS (Basic Input/Output System) is a program that deals with the basic level of communication between processor and peripherals. Use the BIOS Setup program only when ► Standard CMOS Features ► PC Health Status installing motherboard, reconfiguring system, or prompted to “Run Setup”. ► Advanced BIOS Features Load Fail-Safe
ملخص المحتوى في الصفحة رقم 18
3. Driver & Utility The “Driver & Utility CD” that came packed with this motherboard • [Drivers]: Click this button to enter the driver installation menu. contains drivers, utilities and software applications required for its basic [Q-Install]: Click this button to install all the drivers needed for and advanced features. this motherboard at one stroke. Place the “Driver & Utility CD” into the CD-ROM drive in your system. ※ For Windows XP 64-bit and Windows 2003 The following instal
ملخص المحتوى في الصفحة رقم 19
Serial ATA 4. Appendix • 4 個 SATA 3.0Gb/s 4.1 規格（繁體中文） 擴充插槽 • 1 個 PCI-E X16 插槽 處理器 1 • 1 個 PCI-E X1 插槽 • 支援具備1333* /1066/800/533MHz前端匯流排的Intel Core 2 Duo • 2 個 PCI 插槽 / Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D 處理器 1 * FSB1333 的 CPU 速度是以超頻模式進行。在此情形下，PCIE 的頻率也會 內部輸入/輸出接頭 被超頻至 115MHz。 • 1 個軟碟埠 • 支援 Intel Hyper-Threading 技術 • 1 個 Ultra ATA 100 IDE 接頭 • 4 個 SATA 3.0Gb/s 接頭 晶片組 • 2 個 USB 2.0 接頭 • Intel 945GC / ICH7 • 1 個 FP-Audio 接頭 記憶體 • 1 個 CD-In 接頭 2 • 2 條 240
ملخص المحتوى في الصفحة رقم 20
扩充插槽 4.2 规格（简体中文） • 1 个 PCI-E X16 插槽 处理器 • 1 个 PCI-E X1 插槽 1 • 支 持具备 1333* /1066/800/533MHz 前端 总线的 Intel Core 2 Duo / • 2 个 PCI 插槽 Pentium Dual-Core / Pentium D / Pentium 4 / Celeron D 处理器 内部输入/输出接头 • 支持 Intel 超线程技术 1 • 1 个软盘端口 * FSB1333 的 CPU 速度是以超频方式进行。在此情形下，PCIE 的频率也会被 超频至 115MHz。 • 1 个 Ultra ATA 100 IDE 接头 • 4 个 SATA 3.0Gb/s 接头 芯片组 • 2 个 USB 2.0 接头 • Intel 945GC / ICH7 • 1 个 FP-Audio 接头 • 1 个 CD-In 接头 内存 2 • 2 条 240 针脚 DIMM 插槽支持最大 4GB* 内存容量 后面板输入/输出接头 3 • 支持双信道 DDR2
