ملخص المحتوى في الصفحة رقم 1
Intel845GL/GV Main board
User’s Manual
Rev: 1.0/1.2
PCB: M248
CONTENTS
CHAPTER 1 PACKAGE CONTENTS………………….…………………
CHAPTER 2 INTRODUCTION……………………….…………………...
CHAPTER 3 MAIN BOARD LOCATIONS……………………………….
CHAPTER 4 INSTALLATION…………………………….………………
4.1 JUMPER SETTING AND SLOT…………………….………………
4.2 CPU INSTALLATION……………………………………………….
4.3 MEMORY INSTALLATION………………………………………..
4.4 IDE DEVICES INSTALLATION…………………………………...
4.5 OTHER DEVICE INSTALLATION………………………………...
CHAPTER 5 D
ملخص المحتوى في الصفحة رقم 2
Chapter 1 Package Contents Your main board package contains the following items: 1. One M248 Rev:1.0/1.2 main board 2. One 80-Pin Ultra DMA 66/100 IDE drive ribbon cable 3. One 34-Pin Floppy drive ribbon cable 4. One front panel connector ribbon cable (optional) 5. Software Install CD 6. One user’s manual Chapter 2 Introduction This main board has the Intel 845GL/GV chipset that contains Intel 82845GL/GV Memory Controller Hub and Intel 82801DB I/O Controller Hub. This ma
ملخص المحتوى في الصفحة رقم 3
-Integrated display function technologies without extend VGA card Integrated 2D/3D Graphics Controller -USB Ports Six USB ports Supports compliant with Universal Serial Bus Specification Revision 2.0 -BIOS Supports Supports Plug and Play Supports Advanced Power Management Interface -IDE Port Provides two channel connecting four IDE drives Supports Ultra ATA66/100 synchronous DMA modes -I/O Ports One Floppy port support format 360k/720k/1.2M/1.44M/2.88M disk driver One serial
ملخص المحتوى في الصفحة رقم 4
Chapter 3 Main board Locations
ملخص المحتوى في الصفحة رقم 5
Chapter 4 Installation 4.1 Jumper Setting and Slot FSB CPU Frequency Jumper Setting JUMPER AUTO (Default) 400 533 JP1 1-2 2-3 OPEN JP3: Clear CMOS Jumper Setting 1-2 (Default) Normal 2-3 Clear CMOS Audio: Front panel Jumper setting PIN Function PIN Function 1 MIC+ 2 Ground 3 Vbias 4 AuD_Vcc (AVCC) 5 AuD_R_Out 6 AuD_R_Out Back 7 N.C. 8 Key 9 AuD_L_Out 10 AuD_L_Out Back Note: 5-6, 9-10 pin short is default. (Reference main board bitmap) USB: Expansion Connector
ملخص المحتوى في الصفحة رقم 6
Connectors PS/2 (Bottom) PS/2 Keyboard (Down Purple) PS/2 (Top) PS/2 Mouse Header (Up Green) USB 0/1 USB 0/1 Connector Port USB 2/3 USB 2/3 Connector Port LPT Printer Connector Port VGA VGA Display Connector Port COM1 Serial Ports COM1 Connector Port GAME/MIDI Game/MIDI Port LINE OUT/LINE IN/MIC Audio Output/Audio Input/Microphone CD_IN CD-ROM Audio Input Port IDE1/IDE2 Primary IDE/Secondary IDE Port FDD Floppy Disk Drive Connector Port PW1 ATX_20 Power Supply Connector Port PW2
ملخص المحتوى في الصفحة رقم 7
ملخص المحتوى في الصفحة رقم 8
4.3 Memory installation This main board supports DDR200/DDR266 DDR memory you may install 64/128/256/512MB 184 pin DDR memory. DDR SDROM uses additional power and ground lines and requires 184-pin 2.5V unbuffered DIMM module rather than the 168- pin 3.3V unbuffered DIMM used by SDRAM. Follow these instructions to install the Memory: 1. Push the latches on each side of the DIMM slot down. 2. Align the memory module with the slot. The DIMM slots are keyed with notches and the DI
ملخص المحتوى في الصفحة رقم 9
4.5 Other Device Installation 4.5.1 Floppy Disk Drive Installation This main board ships with a floppy disk drive cable that can support one or two drives. Drives can be 3.5” or 5.25” wide, with capacities of 360K, 720K, 1.2MB, 1.44MB, or 2.88MB. Install your drives and connect power from the system power supply. Use the cable provided to connect the drives to the floppy disk drive connector floppy. 4.5.2 Sound Connector Port Installation This main board has three audio por
ملخص المحتوى في الصفحة رقم 10
These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 20-pin ATXPWR1 connector, connect the 4-pin ATX +12v power plug to provide sufficient power to the CPU. Note1: Make sure that you ATX 12V power supply can provide at least 15A on the +12V lead and at least 2A on the +5-volt standby lead (+5
ملخص المحتوى في الصفحة رقم 11
Click “NEXT” to continue Select “YES” to continue
ملخص المحتوى في الصفحة رقم 12
Select “NEXT” to continue Select “FINISH” completing the installation.
ملخص المحتوى في الصفحة رقم 13
5.3 IAA (Intel Application Accelerator) Setup Insert the driver CD, running driver software CD, choose the directory: \CD-ROM:\INTEL\IAA\XXX Click “Next” to continue Select “Yes” to continue
ملخص المحتوى في الصفحة رقم 14
Select “Next” to continue Select “Next” to Continue
ملخص المحتوى في الصفحة رقم 15
Select “Finish” to complete the installation 5.4 Sound Driver Setup 5.4.1 Sound driver setup (For Realtek series of WIN98 operation system) Insert the driver CD, running driver software CD, choose the Directory:\CD-ROM:\SOUND\REALTEK\SETUP.EXE Select “Next” to continue
ملخص المحتوى في الصفحة رقم 16
Select “Finish” to complete the installation Channel Sound Output Support Please follow the steps below for operation (optional): 1. After install sound driver’ click “Sound effect”, “AC97 audio configuration” options; 2. Click “Sound configuration” select “6 Channel mode for 5.1 speakers output” options. 3. Click “Sound effect” menu “Environment” you must choose one Sound effect realization 6-Channel sound output. 5.4.3 Uninstallation Sound Driver (For Realtek of WIN98 operatio
ملخص المحتوى في الصفحة رقم 17
Select “Device manager” to continue Select “PCI Universal Serial Bus” and double click to continue
ملخص المحتوى في الصفحة رقم 18
Select “Reinstall Driver” to continue Select “Next” to continue
ملخص المحتوى في الصفحة رقم 19
Select “Next” to continue Select “Specify a location” and type “F:\INTEL\USB20\845\WIN98_ME” that
ملخص المحتوى في الصفحة رقم 20
Select “Next” to continue Select “Next” to Continue
