ملخص المحتوى في الصفحة رقم 1
Before You Begin…
Parts NOT in the Kit
This kit contains all the hardware necessary to install and connect your new EVGA
e-7050/610i GPU motherboard with integrated GeForce graphics processing. However, it
does not contain the following items that must be purchased separately to make the
motherboard fully functional.
Intel microprocessor:
Cooling fan and heat sink for the microprocessor
System memory support
Hard Disk Drive(s)
Operating System
Power Supply
Graph
ملخص المحتوى في الصفحة رقم 2
Onboard Serial ATA II • 3Gb/s data transfer rate • Four Serial ATA II connectors • Support for RAID 0, RAID 1 • Supports hot plug and NCQ (Native Command Queuing ) Onboard LAN • LAN interfaces built-in onboard • 10/100 LAN Onboard Audio • Supports 6-channel audio • Supports Jack-Sensing function PCI Express x16 Support • Supports 4 GB/sec (8 GB/sec concurrent) bandwidth Onboard Video • Integrated video • A VGA output is provided Expansion Slots • Two PCI slots • One
ملخص المحتوى في الصفحة رقم 3
Hardware Installation This section will guide you through the installation of the motherboard. The topics covered in this section are: • Preparing the motherboard • Installing the CPU • Installing the CPU fan • Installing the memory • Installing the motherboard • Connecting cables and setting switches Safety Instructions To reduce the risk of fire, electric shock, and injury, always follows basic safety precautions. Remember to remove power from your computer by disconnecting t
ملخص المحتوى في الصفحة رقم 4
15 12 12 13 14 16 17 11 1 18 10 19 10 2 3 4 5 8 6 9 7 1. CPU Socket 10. USB 2.0 Header 19. Clear CMOS Jumpe er 2. NVIDIA MCP with Passive Cooling 11. Front Panel Audio Head der 3. 4-Pin CPU Fan Connector 12. PCI S Slots 4. DDR2 DIMM Mem mory Slots 13. PCI-E E x1 Slot 5. FDD Connector 14. PCI-E E x16 Slot 6. 24-Pin ATX Power r Connector 15. Back k Panel Connectors 7. IDE HDD Connect tor 16. 4-Pin n CPU Power Conne ector
ملخص المحتوى في الصفحة رقم 5
2 1 3 4 5 5 6 1. PS/ /2 Keyboard Po ort 2. LAN N Port with LED Ds to indicate s status: Activity LED Speed/Link L LED Status Description Description Status Off No data transmission n Gree en 100 Mbps data rate Blinking (Green) Data transmission Offf 10 Mbps data rate 3. PS/ /2 Mouse Port 4. e-7 7050 Integrated d Graphics VGA A Output 5. USB B 2.0 ports (Fo our) 6. Aud dio Port 2-C Channel 6-Channel Gre een Lin ne-Out Front Speake er Out Pink Mic c In Mic In Ora
ملخص المحتوى في الصفحة رقم 6
Preparing the Motherboard Installing the CPU Be very careful when handling the CPU. Hold the processor only by the edges and do not touch the bottom of the processor. Use the following procedure to install the CPU onto the motherboard. 1. Unhook the socket lever by pushing down and away from the socket. 2. Lift the load plate. There is a protective socket cover on the load plate to protect the socket when there is no CPU installed. 3. Remove the protective socket cover from the load pl
ملخص المحتوى في الصفحة رقم 7
Installing the Motherboard The sequence of installing the motherboard into the chassis depends on the chassis you are using and if you are replacing an existing motherboard or working with an empty chassis. Determine if it would be easier to make all the connections prior to this step or to secure the motherboard and then make all the connections. Use the following procedure to install the I/O shield and secure the motherboard into the chassis. Note: Be sure that the CPU fan assembly has
ملخص المحتوى في الصفحة رقم 8
Pow wer Con nnection ns This mothe erboard requir res an ATX power supply. Make sure yo our power sup pply can provide enough wattage to power all t the componen nts you will be e installing. 24-pin ATX Pow wer (PWR1) PWR1 is th he main power supply conn nector located along the edg ge of the board d next to the DIMM slots. Make sure that the powe er supply cable and pins are e properly alig gned with the connector on the mothe erboard. Firmlly plug the pow wer supply cable into the co onn
ملخص المحتوى في الصفحة رقم 9
Co onnecting S Serial ATA C Cables The Serial A ATA II conne ector is used t to connect the e Serial ATA II dev vice to the mo otherboard. T These connecto ors support the thin Serial ATA II ca ables for prim mary storage de evices. The current Ser rial ATA II int terface allows up to 300MB B/s data transfer rat te. T There are four serial ATA co onnectors on t the motherbo oard. These co onnectors sup pport RAID 0, RAID 1. Co onnecting Internal Hea aders Pllease refer to #
ملخص المحتوى في الصفحة رقم 10
Audio The audio connector supports the HD audio standard. Most cases come with a 10 pin standard block which will align and plug directly in to the header. In some cases there will be individual plugs which will need to be plugged in. Table 1. Front Audio Connector Connector Pin Signal 1 PORT1_L - Analog Port 1 - left channel (Microphone) Front Audio Connector 2 AUD_GND - Ground 3 PORT1_R – Analog Port 1 – right channel (Microphone) 1 2 4 PRESENCE# - Active signal tha
ملخص المحتوى في الصفحة رقم 11
Expansion Slots The EVGA nForce motherboard contains four expansion slots, two PCI Express slots and two PCI slots. PCI Slots The two PCI slots support many expansion cards such as a LAN card, USB card, SCSI card and other cards that comply with PCI specifications. When installing a card into the PCI slot, be sure that it is fully seated. Secure the card’s metal bracket to the chassis back panel with the screw used to hold the blank cover. PCI Express x1 Slot There is one PCI
