ملخص المحتوى في الصفحة رقم 1
LMC5022C-R3 LMC5110C-R3 LMC5116C-R3 LMC5182C-R3
LMC5023C-R3 LMC5111C-R3 LMC5117C-R3
LMC5026C-R3 LMC5113C-R3 LMC5180C-R3
LMC5027C-R3 LMC5114C-R3 LMC5181C-R3
High-Density Media Converter System II Layer 2 Modules
True Layer 2 conversion enables
you to extend your network
up to 40 kilometers over duplex fiber.
ملخص المحتوى في الصفحة رقم 2
FCC and IC RFI Statements FCC and Industry Canada RF Interference Statements Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses, and c
ملخص المحتوى في الصفحة رقم 3
Certifications Certifications Class 1 Laser product, Luokan 1 Laserlaite, Laser Klasse 1, Appareil A’Laser de Classe European Directive 2002/96/EC (WEEE) requires that any equipment that bears this symbol on product or packaging must not be disposed of with unsorted municipal waste. This symbol indicates that the equipment should be disposed of separately from regular household waste. It is the consumer’s responsibility to dispose of this and all equipment so marked th
ملخص المحتوى في الصفحة رقم 4
Table of Contents Table of Contents Part Numbers .................................................................................................. 5 1. Specifications............................................................................................ 6 2. Overview: About the High-Density Media Converter System II Layer 2 Modules........................................................................................................... 7 3. Configuration...........................
ملخص المحتوى في الصفحة رقم 5
Part Numbers Part Numbers Part Number Description LMC5022C-R3 TX/FX-MM1300-ST LMC5023C-R3 TX/FX-MM1300-SC LMC5026C-R3 TX/FX-SM1310/PLUS-ST LMC5027C-R3 TX/FX-SM1310/PLUS-SC LMC5110C-R3 TX/FX-SM1310/LONG-SC LMC5111C-R3 TX/FX-SM1310/LONG-ST LMC5113C-R3 TX/SSFX-SM1310-SC (1310xmt/1550rcv) LMC5114C-R3 TX/SSFX-SM1550-SC (1550xmt/1310rcv) LMC5116C-R3 TX/SSFX-SM1310/PLUS-SC (1310xmt/1550rcv) LMC5117C-R3 TX/SSFX-SM1550/PLUS-SC (1550xmt/1310rcv) LMC5180C-R3 TX/FX-SM1550/LONG-SC L
ملخص المحتوى في الصفحة رقم 6
Chapter 1: Specifications 1. Specifications DC Input L2 w/LFPT: 0.80 Amp @ 5V Operating Temperature: +32° F to +122° F (0° C to +50° C) Storage Temperature: 0° F to +122° F (-20° C to +70° C) Humidity: 5 - 95% (non-condensing) Fiber Optic Specifications For fiber optic specifications, please visit: http://www.blackbox.com Page 6 724-746-5500 | blackbox.com LMC5022C-R3
ملخص المحتوى في الصفحة رقم 7
Chapter 2: Overview 2. Overview: About the High-Density Media Converter System II Layer 2 Modules The L2 is a Fast Ethernet module which provides a single conversion between 100BASE-TX twisted pair and 100BASE-FX/SX single-mode or multi-mode fiber. Each L2 includes one RJ-45 connector and one pair of ST or SC fiber optic connectors Also available in a single-strand fiber version, L2 TX/SSFX allows two wavelengths to share one fiber strand — Full-Duplex data travels on different wa
ملخص المحتوى في الصفحة رقم 8
Chapter 3: Configuration 3. Configuration The L2 has user-configurable features (e.g., FiberAlert (FA), TX LinkLoss (TXLL), FX LinkLoss (FXLL), Link Fault Pass-Through (LFPT) and Far End Fault (FEF)). Refer to the Managed Media Converter Module DIP Switch Configuration Table for information on available features. Instructions for installing and configuring both managed (via an SNMP-compatible management application like iView²) and unmanaged modules follow. Page 8 724-746-5
ملخص المحتوى في الصفحة رقم 9
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules 4. Install the High-Density Media Converter System II Layer 2 Modules The Managed Media Converter Modules install in Black Box SNMP manageable High-Density Media Converter System II chassis. NOTE All modules are hot-swappable. To install a Managed Media Converter Module: 1. Remove the blank bracket covering the slot where the module is to be installed by removing the screws on the outside edges of the br
ملخص المحتوى في الصفحة رقم 10
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules SNMP Management Module, the High Density L2 Module with Configuration Control will function based on its DIP Switch settings. If the DIP Switches have not been changed, the stored configuration will be used. The stored configuration can be extracted from the SNMP Management Module or the DIP Switches. • Replacing the same type of a High Density L2 Module with Configuration Control - If the DIP Switch setti
ملخص المحتوى في الصفحة رقم 11
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules DIP Switch on S1 Feature Default Setting 1 Auto Negotiation (AN) ON 2 Far End Fault (FEF) OFF 3 FX LinkLoss (FXLL) OFF 4 TX LinkLoss (TXLL) OFF 5 FiberAlert (FA) OFF 6 Factory Default OFF 7 Factory Default OFF 8 Factory Default OFF 4.3 FX LinkLoss, TX LinkLoss, Link Fault Pass-Through, Far End Fault and FiberAlert L2 modules include the troubleshooting features FiberAlert, TXLL, FXLL, FEF and LFPT
ملخص المحتوى في الصفحة رقم 12
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules pulses, it knows that the device to which it is connected is up and sending pulses, and that the copper or fiber cable coming from that device is intact. The appropriate “LNK” (link) LED is lit to indicate this. The Black Box media converter also sends out link pulses from its copper and fiber transmitters, but normally has no way of knowing whether the cable to the other device is intact and the link pulse
ملخص المحتوى في الصفحة رقم 13
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules Regardless if there is a break in segment 1, 2 or 3, the link will drop on the switches at both ends. The link fault is passed through the media conversion and is observed at each end. It acts just like it would if the devices were directly connected. For more information on LinkLoss/FiberAlert, visit the Black Box Web site at http://www.blackbox.com. If unsure of how to implement these features in a
ملخص المحتوى في الصفحة رقم 14
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules WARNING Enable FiberAlert at the remote side of a media conversion only. Enabling it on both sides would keep both transmitters disabled indefinitely. By default FA is disabled. When enabled if, a fault occurs on the fiber line, affecting data in one direction, FA stops sending signal in the opposite direction. FXLL will act on this lack of signal, propagating the loss of like to the copper port when F
ملخص المحتوى في الصفحة رقم 15
Chapter 4: Install the High-Density Media Converter System II Layer 2 Modules 4.4 Auto Negotiation on High-Density Media Converter System II Layer 2 Modules L2 modules include the feature Auto Negotiation. When Auto Negotiation is enabled, the module negotiates as a 100 Mbps full-duplex device. If the connected device can operate at 100 Mbps full-duplex, a link is established. Auto Negotiation (DIP Switch #1) is enabled by default. If the twisted pair port on the other device does
ملخص المحتوى في الصفحة رقم 16
Chapter 5: Operation 5. Operation 5.1 LED Operation Each L2 module features diagnostic LEDs that provide information on features and ports. Upgrade LED Stacks Upper Function State FEF Fiber Far End Fault ON Green TXLL TX LinkLoss/Blink if Active ON Green LNK FiberLink is valid/Flash on Activity ON Green DIS Software Disabled TX Port On Yellow Upper Function State FA FiberAlert enabled/Blink Active ON Green FXLL FX LinkLoss/Blink if Active ON Green LNK FX LinkLoss is valid/Fla
ملخص المحتوى في الصفحة رقم 17
Chapter 6: Troubleshooting 6. Troubleshooting • During installation, first test the fiber and twisted pair connections with all troubleshooting features disabled, then enable these features, if desired, just before final installation. This will reduce the features’ interference with testing. • When working with units where the features cannot be disabled, establish both the twisted pair and fiber connections before the link LEDs will light. • To test a L2 by itself, first, have an
ملخص المحتوى في الصفحة رقم 18
Chapter 7: Contacting Black Box 7. Contacting Black Box Black Box Customer Service Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) Free technical support, 24 hours a day, 7 days a week. Call: 724-746-5500 or Fax: 724-746-0746 Mail order: Black Box Corporation 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com E-mail: info@blackbox.com WARNING Disconnect all power supplies before servicing. Page 18 724-746-5500 | blackbo
ملخص المحتوى في الصفحة رقم 19
Chapter 8: Fiber Optic Cleaning & ESD Precautions 8. Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules. 1. Use fiber patch cords (or connectors, if you terminate your own fiber) only from a reputable supplier; low-quality components can cause many hard-to-d
ملخص المحتوى في الصفحة رقم 20
LMC5022C-R3, Rev. 1 50-80921BB-01 Rev A0
