Antec Performance TX1050B دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

USER’S MANUAL
Performance
TX1050B / 1088AMG
User's Manual

ملخص المحتوى في الصفحة رقم 2

At Antec, we continually refine and improve our products to ensure the highest quality. So it's possible that your new case may differ slightly from the descriptions in this manual. This isn't a problem; it's simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec's Computer Enclosures. For more comprehensive instructions on installing your motherboard and peripher

ملخص المحتوى في الصفحة رقم 3

3. Line up your motherboard with the standoff holes, and remember which holes are lined up. Not all motherboards will match with all the provided holes; this is normal, and won't affect functionally. (In other words, there will likely be extra holes.) 4. Remove your motherboard by lifting it up. 5. Screw the brass standoffs into the threaded holes that line up with your motherboard. Do not overtighten the standoffs. Some standoffs may be pre-installed for your convenience. 6. Place your mother

ملخص المحتوى في الصفحة رقم 4

Intel Standard USB Header Pin Layout 1 2 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Pin) 10 Empty Pin 9 10 CONNECTING THE IEEE 1394 (FIREWIRE®, I.LINK®) PORT You will find a single 10-pin connector on a cable attached to the front IEEE 1394 connection. This is an Intel standard connector, which is keyed so that it can't be accidentally reversed as long as it is conne

ملخص المحتوى في الصفحة رقم 5

6. Rear Right Speaker Out Pin: Connect the RET-R connector to this pin. 7. Rear Left Speaker Out Pin: Connect RET-L connector to this pin. 3.5" DEVICE INSTALLATION With the front bezel facing you, swing the front door out. You can see there are four 5.25" and two 3.5" external drive bays. Inside the case there are four 3.5" drive cages. 1. Pull the quick release lever towards the rear of the case and release the top cage first. Looking from the rear of the case you can see some metal grills over

ملخص المحتوى في الصفحة رقم 6

Specifications: Size: 120 x 120 x 25.4 mm Rated Voltage: DC 12V Input Static Acoustical Input Speed Air Flow Current Pressure Noise Power High 0.24A 2.24 m³/min. 2.54 mm-H2O 30 dBA 2.9 W 2000 RPM (Max.) (79 CFM) (0.10 inch-H2O) Medium 1.59 m³/min. 1.53 mm-H2O 0.2A 28 dBA 2.4 W 1600 RPM (56 CFM) (0.06 inch-H2O) Low 1.1 m³/min. 0.92 mm-H2O 0.13A 1.6 W 25 dBA 1200 RPM (39 CFM) (0.04 inch-H2O) This case comes with two 80mm front fan mounts, one 80mm side panel fan mount for the VGA card and one 92mm

ملخص المحتوى في الصفحة رقم 7

the fan duct down to the CPU. Note: Lower the guide down as low as possible without touching the CPU cooler. This is the most common way to cool a CPU that comes with a stock cooler. Performance Mode If you are a high performance user and you need extra cooling for your CPU. 1. Remove the side panel from the case. 2. Install a 92mm fan to the fan hood so that the air is blowing down to the CPU cooler. 3. Lower the lower air guide with fan down to the CPU cooler. This will bring extra fresh, cool

ملخص المحتوى في الصفحة رقم 8

Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 Tel: 510-770-1200 Fax: 510-770-1288 Antec Europe B.V. Sydneystraat 33 3047 BP Rotterdam The Netherlands Tel: +31 (0) 10 462-2060 Fax: +31 (0) 10 437-1752 Technical Support US & Canada 1-800-22ANTEC CustomerSupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2005 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners. Reproduction in whole or in part without writt