ملخص المحتوى في الصفحة رقم 1
SD-M1201 DVD-ROM
with REALmagic Hollywood+ Playback Card
Installation Instructions
Congratulations on your purchase of a Toshiba SD-M1201 DVD-ROM
drive and REALmagic Hollywood+ DVD/MPEG-2 Playback Card Kit.
The following information will help you in the simple installation of
your new DVD-ROM. It is assumed that you are replacing a presently
installed CD-ROM with the enclosed DVD-ROM. If this is not the case,
additional installation hardware may be required. Refer to REALmagic
Hollywood+ User’
ملخص المحتوى في الصفحة رقم 2
The follow steps must be performed to properly install your DVD-ROM. l Set DVD-ROM drive jumper settings. l Connect audio cable. l Install SCSI host adapter board. l Attach SCSI interface cable. l Mount DVD-ROM. SETTING JUMPERS The block of mode select jumpers are located on the rear of the DVD- ROM. If the jumper covers both pins on the jumper block, it is ON; if there is no jumper or only one of the pins is covered, the jumper is OFF. The jumper settings include SCSI ID, Parity, Termination,
ملخص المحتوى في الصفحة رقم 3
PRV/ALW - This jumper is used to inhibit the drive’s EJECT button. When the jumper is ON, the EJECT button will not operate. Test - This setting selects the drive operation between normal CD-ROM and CD-Audio player mode. When jumper is set to ON position, com- mands from the host computer are ignored. This jumper is for test pur- poses only and should be set to OFF for proper CD-ROM function. Power Supply - Toshiba SCSI DVD-ROM drives can supply power to other equipment on the SCSI BUS. When
ملخص المحتوى في الصفحة رقم 4
If you are replacing your CD-ROM: connect DVD-ROM to the SCSI interface connector that the CD-ROM was connected to. If DVD-ROM is not replacing a CD-ROM or is an addition to a CD-ROM: daisy-chain the DVD-ROM drive with a custom built SCSI interface cable (not supplied with kit). See Daisy-Chaining Section on page 5 for more information. Power Cable - Connect an internal computer power supply cable to the power socket at the back of the DVD-ROM. One side of the plug has chamfered edges, so the
ملخص المحتوى في الصفحة رقم 5
Daisy-Chaining - If the DVD-ROM you are installing is one of two or more SCSI devices you are connecting to your system, you will need to use a custom built SCSI interface cable. Remember that the terminator jumper on the DVD-ROM drive must have the jumper installed when the drive is the last device in the chain. Host Computer Interface I/F Card Connector SCSI Cable DVD-ROM DRIVE (see note 1) Terminator SD-M1201 CONNECTION (ONE DRIVE) SD-M1201 INTERNAL DRIVE(S) Host Computer SCSI Cable Interfa
ملخص المحتوى في الصفحة رقم 6
COMPLETING INSTALLATION After you have connected all the necessary cables, push the DVD-ROM completely into the computer’s drive slot. Mount drive accord- Mounting Screw ing to your computer’s instruc- M3 tions. The screw length should Mounting frame of not exceed 3±0.5mm (measured host computer from outside surface of side or Surface of side or bottom bottom of DVD-ROM to tip of of DVD-ROM drive screw). Replace computer cover and all outer screws. 2.5 - 3.5mm Software Driver: The T
ملخص المحتوى في الصفحة رقم 7
DVD-ROM BACK PANEL The photo illustrates the following features of the SD-M1202 DVD-ROM back panel: ① Analog audio out connector ② Mode select jumper ③ SCSI interface connector ④ Power connector 7
ملخص المحتوى في الصفحة رقم 8
TECHNICAL SUPPORT Technical support can be obtained by calling 949/455-0407. Drivers are available on BBS at 949/837-8864 or on our web site at http://www.toshiba.com SD-M1201 SPECIFICATIONS DVD CD-ROM Data Capacity (bytes/block) 2,048 mode 1 mode 2 2,048 2,336 Rotational Speed (approx. rpm) 2,900 13.8 ~ 32X: 6,900 8.6 ~ 20X: 4,300 (CD-RW) 4 ~ 5.7X: 1,200-2,000 (audio) Sustained Data Transfer Rate 2,797 ~ mode 1 mode 2 (kbytes/sec) 6,760 2,069 ~ 2,360 ~ 4,800 5,475 Access Time (Typ.) Avg. Rando
