ملخص المحتوى في الصفحة رقم 1
CD-ROM DRIVE
(T)XM6401B/F1
HARDWARE
INSTRUCTION MANUAL
VERSION 2.0
APRIL 2000
Covers.p65 1 6/13/00, 2:58 PM
ملخص المحتوى في الصفحة رقم 2
CD-ROM DRIVE Hardware Instruction Manual For the following CD-ROM Drives: XM-6401B TXM6401F1 TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC. Storage Device Division 35 Hammond Irvine, CA 92618 Contents of this manual are subject to change without prior notice. © 1998 TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC. All rights reserved Printed in USA TOSHIBA XM-6401B/TXM6401F1 CD-ROM Drive i P/N 470073-B0
ملخص المحتوى في الصفحة رقم 3
CERTIFICATION This equipment complies with the following standards: XM-6401B TXM6401F1 UL 1950 Electrical Business Equipment UL 1950 Electrical Business Equipment CAN/CSA: TD STD 950/UL 1950 CSA Standard C22.2 No. 234 TUV EN 60950/08.92, A1/01.93, A2/08.93 60929/09/.91 N/A FCC Class B - specification limits defined by FCC Class B - specification limits defined EN55022 for information Technology Equip. by EN55022 for information Technology Equip. IEC Standard: IEC 801-2: 1992 IEC 801-3: 1994, EN
ملخص المحتوى في الصفحة رقم 4
LASER CAUTION This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT". To use this model properly, read this Owner's Manual carefully and keep this manual for future reference. In case of any trouble with this model, please contact your nearest "Authorized Repair Center". To prevent direct exposure to the laser beam, do not try to open the enclosure. CAUTION! • REFLECTIVE OBJECTS SHOULD NOT BE PLACED IN THE DISK SLOT DUE TO POSSIBLE HAZARDOUS RADIATION EXPOSURE.
ملخص المحتوى في الصفحة رقم 5
Table of Contents Introduction ............................................................................. 1 SCSI drives ............................................................................ 2 Installing CD-ROM ................................................................. 3 Installation Requirements ...................................................... 3 Installing an Internal CD-ROM ............................................. 3 CD-ROM Jumper Settings ............................
ملخص المحتوى في الصفحة رقم 6
Introduction ongratulations on the purchase of your Toshiba XM-6401B CD-ROM drive. This manual will Cprovide you with the information you will need to install and operate your new CD-ROM. This manual covers both the internal CD-ROM (XM-6401B) and the external CD-ROM (TXM6401F1). Instructions in this manual apply to both models, unless otherwise stated. The XM-6401B is one of the fastest CD-ROM drives currently avail- able. Features include: ➬ 40X speed Brings leading edge performance. ➬ Tray o
ملخص المحتوى في الصفحة رقم 7
SCSI DRIVES he XM-6401B is a SCSI-2 (Small Computer Systems Inter- face) device. Some other SCSI devices you may already have T connected to your computer are scanners, tape drives, or an- other CD-ROM drive. PC SYSTEMS: To add a SCSI device to your computer, you must have a SCSI interface card already in place. The interface card fits into one of the slots inside your computer and connects to your CD-ROM device via a SCSI cable. Your CD-ROM also requires a software driver to be installed. This
ملخص المحتوى في الصفحة رقم 8
Installing CD-ROM efore you begin to install your CD-ROM, make sure you have the items listed below. In most cases, these items will B not come with your CD-ROM. See your local computer re- tailer to purchase them. INSTALLATION REQUIREMENTS ❑ CD-ROM Software Driver (when installing on a PC the software driver must be written for the SCSI host adapter card you have installed in your computer system) ❑ SCSI Host Adapter Board (PC systems only) ❑ SCSI Interface Cable ❑ External Terminator (TXM6401F
ملخص المحتوى في الصفحة رقم 9
POWER TEST PRV/ALW TERM ON/OFF PRTY ID4 ID2 ID1 IMPORTANT NOTE Before you begin installing your CD-ROM, make sure your computer is switched OFF and the power cable is disconnected. CD-ROM JUMPER SETTINGS In order for your CD-ROM to work properly, it may be necessary for you to change the CD-ROM’s jumper settings. Locate the block of jumpers on the back left side of the CD-ROM. Jumper Location Jumpers can be set in either an ON mode or OFF mode. If the jumper covers both pins on the jumper block,
ملخص المحتوى في الصفحة رقم 10
All SCSI devices attached to your computer are assigned a SCSI-ID number from 0 to 7. Your CD-ROM’s SCSI ID must be set so that its ID number does not conflict with any other device’s SCSI-ID in your system. In most cases your CD-ROM will come set to SCSI ID 0. If your CD-ROM is the only SCSI device connected to your computer, you should leave the jumpers as they are. If you have additional SCSI devices (another CD-ROM, hard drive, etc.) you will be “daisy-chain- ing” these devices. Each SCSI
ملخص المحتوى في الصفحة رقم 11
Terminator ON/OFF Jumper This jumper turns termination power ON or OFF. If you are “daisy- chaining” a series of SCSI devices (connecting more than one SCSI device to your system), and the XM-6401B CD-ROM is not at the end of the chain, you must remove the jumper. Eject Prevention Jumper This jumper is used to inhibit the operation of the drive’s EJECT but- ton. When jumper is set to ON (jumper present), the EJECT button will not operate. Setting the jumper to OFF (no jumper present) will allow
ملخص المحتوى في الصفحة رقم 12
PLACING CD-ROM INSIDE YOUR COMPUTER You are now ready to install your CD-ROM inside your computer. You should refer to the book that came with your computer, as com- puter casings are different from each other. Usually the casing is at- tached to the frame by a number of screws at the back. Turn your computer around, so the back faces you, and look for 4 or 6 screws around the edge of the casing. Remove the screws and put them some- where safe. Lift or slide casing away from computer frame, an
ملخص المحتوى في الصفحة رقم 13
CABLING SCSI - The internal SCSI interface cable is connected to your SCSI host adapter card and fits into the socket on the back of your CD- ROM. The stripe side (or red-colored side) of the ribbon cable con- nects to pin 1 on the drive’s SCSI connector which is found next to the drive’s power connector. Carefully push the SCSI connector into the socket, making sure it fits snugly. Attaching SCSI Cable Power - Apply power to your CD-ROM by connecting your computer’s +12V/+5V power cable to the
ملخص المحتوى في الصفحة رقم 14
If there is no power cable in your system, contact your computer dealer. You may need a “power splitter lead” (a Y shaped cable which taps two power outputs from one input). Sound (optional) - If you have a sound card and speakers and would like to play audio CDs on your computer, you will need to get a sound cable. Contact our small parts supplier, AMC at 888/262-9700. Sound cables are made for the sound card you are using and the CD-ROM drive you are connecting it to. Make sure you have thi
ملخص المحتوى في الصفحة رقم 15
Daisy-Chaining - If the CD-ROM you are installing is one of two or more SCSI devices you have connected to your system, you will need to use a custom built SCSI interface cable. Remember that the termi- nator jumper on the CD-ROM drive must have the jumper installed when the drive is the last device in the chain. T X Host Computer M I/F Card Interface 6 SCSI Cable Connector 4 0 CD-ROM DRIVE 1 F Terminator External Terminator 1 (see notes 1 & 3) Host Computer Interface X I/F Card Connector SCSI
ملخص المحتوى في الصفحة رقم 16
COMPLETING INSTALLATION After you have connected all the necessary cables, you can push the CD-ROM completely into the slot. There are 12 screw holes on the XM-6401B that are used to mount the CD-ROM into your computer. The screw length should not exceed 3±0.5mm (measured from out- side surface of side or bottom of CD-ROM to tip of screw). Replace the computer’s cover, and replace all outer screws. Mounting Screw M3 Mounting frame of host computer Surface of side or bottom of CD-ROM dr
ملخص المحتوى في الصفحة رقم 17
INSTALLING AN EXTERNAL CD-ROM (TXM6401F1) The instructions that follow are for use on PC and Macintosh systems. In order to install your external CD-ROM successfully, you will need to complete the following steps. ☛ Install SCSI host adapter board in your computer system (if not already installed). - PC systems only ☛ Set SCSI ID Switch on CD-ROM. ☛ Using a SCSI cable, connect CD-ROM to SCSI interface card or SCSI port. ☛ Connect supplied power cord to CD-ROM. ☛ Load CD-ROM driver software. IMPO
ملخص المحتوى في الصفحة رقم 18
SCSI ID Switch TERMINATION If the CD-ROM is being installed as the last drive in a daisy-chain or as the only SCSI device, you must install an external terminator on one of the SCSI connectors at the rear of the CD-ROM. External Terminator TOSHIBA XM-6401B/TXM6401F1 CD-ROM Drive 13
ملخص المحتوى في الصفحة رقم 19
CABLING SCSI - Locate the SCSI interface card connection or SCSI port at the back of your computer. Plug the SCSI cable into socket, making sure it fits snugly. (If the plug has fixing screws or clips, use them to ensure the connector is firmly fixed.) Plug the other end of the cable into one of the sockets found on the back of the CD-ROM drive (the other connector should have a terminator installed, or if daisy-chaining, be attached to another SCSI device). You must use a daisy-chain cable if y
ملخص المحتوى في الصفحة رقم 20
SOFTWARE In order for your computer to recognize the CD-ROM, you must in- stall a CD-ROM software driver. PCs - If you do not have this software, contact the manufacturer of your SCSI host adapter card. Use the instructions that came with your software to install the CD-ROM software driver. TOSHIBA XM-6401B/TXM6401F1 CD-ROM Drive 15
