ملخص المحتوى في الصفحة رقم 1
Product Manual
®
Momentus 4200.3
ST980811A
ST960813A
ST9408116A
100398880
Rev. B
August 2007
ملخص المحتوى في الصفحة رقم 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100398880, Rev. B August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
ملخص المحتوى في الصفحة رقم 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 4
ii Momentus 4200.3 PATA Product Manual, Rev. B
ملخص المحتوى في الصفحة رقم 5
List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Figure 2. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 3. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Momentus 4200.3 PATA Product Manual, Rev. B iii
ملخص المحتوى في الصفحة رقم 6
iv Momentus 4200.3 PATA Product Manual, Rev. B
ملخص المحتوى في الصفحة رقم 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 4200.3 drives: � ST980811A � ST960813A � ST9408116A These drives provide the following key features: � 4,200-RPM class performance (actual spindle speed is 5,400-RPM) � 8-Mbyte buffer � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5. � Tunneling Magnetoresist
ملخص المحتوى في الصفحة رقم 8
2 Momentus 4200.3 PATA Product Manual, Rev. B
ملخص المحتوى في الصفحة رقم 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST980811A, ST960813A, and ST9408116A model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual. Momentus 4200.3 PA
ملخص المحتوى في الصفحة رقم 10
Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST980811A ST960813A Formatted Gbytes (512 bytes/sector)* 80 60 Guaranteed sectors 156,301,488 117,210,240 Bytes per sector 512 Physical read/write heads 2 Discs 1 Cache (Mbytes) 8 Recording density, BPI (bits/inch typical) 835k Track density, TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) 4,200-RPM class performance (actual spindle speed is 5,400-RPM) Internal data transfer rate (Mbi
ملخص المحتوى في الصفحة رقم 11
Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST980811A ST960813A Shock, nonoperating (Gs max at 1 msec) 900 Shock, nonoperating (Gs max at 0.5 msec) 400 Vibration, operating 1.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 10 hz) Vibration, nonoperating 5.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 22 hz) Drive acoustics, sound power (bels), 2 disc Idle** 2.4 (typical) 2.6 (max) Performance seek 2.9 (typical) 3.1 (max) 14 Nonrecov
ملخص المحتوى في الصفحة رقم 12
Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST9408116A Formatted Gbytes (512 bytes/sector)* 40 Guaranteed sectors 78,140,160 Bytes per sector 512 Physical read/write heads 1 Discs 1 Cache (Mbytes) 8 Recording density, BPI (bits/inch typical) 835k Track density, TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) 4,200-RPM class performance (actual spindle speed is 5,400-RPM) Internal data transfer rate (Mbits/sec max) 352 I/O data-t
ملخص المحتوى في الصفحة رقم 13
Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST9408116A Shock, nonoperating (Gs max at 1 msec) 900 Shock, nonoperating (Gs max at 0.5 msec) 400 Vibration, operating 1.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 10 hz) Vibration, nonoperating 5.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 22 hz) Drive acoustics, sound power (bels), 2 disc Idle** 2.4 (typical) 2.6 (max) Performance seek 2.9 (typical) 3.1 (max) 14 Nonrecoverable rea
ملخص المحتوى في الصفحة رقم 14
2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST980811A 80 Gbytes 156,301,488 512 ST960813A 60 Gbytes 117,210,240 512 ST9408116A 40 Gbytes 78,140,160 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blo
ملخص المحتوى في الصفحة رقم 15
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method Perdendicular Recording density BPI (bits/inch typical) 835k Track density TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbits/sec max) 352 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes) 2.6 Physical characteristics Height (mm) 9.5 +/–
ملخص المحتوى في الصفحة رقم 16
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec)* Read Write Track-to-track 1.0 1.5 Average 11.0 13.0
ملخص المحتوى في الصفحة رقم 17
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 11. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/write actuator arm moves
ملخص المحتوى في الصفحة رقم 18
2.9.1.1 Typical current profile Figure 4. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.3 Volt
ملخص المحتوى في الصفحة رقم 19
2.9.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 3: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power
ملخص المحتوى في الصفحة رقم 20
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 0° to 60°C (32° to 140°F) Nonoperating –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour
