ملخص المحتوى في الصفحة رقم 1
C141-E163-01EN
MAP3147FC
MAP3735FC
DISK DRIVES
PRODUCT/MAINTENANCE MANUAL
ملخص المحتوى في الصفحة رقم 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section "Important Alert Items" in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual. IMPORTANT
ملخص المحتوى في الصفحة رقم 3
Preface This manual describes the MAP3147FC, MAP3735FC (hereafter, MAP series), 3.5 type fixed disk drives with an embedded fibre channel controller. This manual details the specifications and functions of the above disk drive, and gives the requirements and procedures for installing it into a host computer system. This manual is written for users who have a basic understanding of fixed disk drives and their use in computer systems. The MANUAL ORGANIZATION section describes organization and sco
ملخص المحتوى في الصفحة رقم 4
Preface APPENDIX A The appendix gives supplementary information, including the signal assignments of interface connectors. Conventions for Alert Messages This manual uses the following conventions to show the alert messages. An alert message consists of an alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a signal word. The following are the alert signals and their meanings: This indicates a hazardous situation likely to result in seriou
ملخص المحتوى في الصفحة رقم 5
Preface (Example) Data loss For MAP series, Reed Solomon codes are applied for their ECC. The sector-data is divided into 6 interleaving sectors, and ECC is performed in each sector where the maximum number of errors (up to 5 byte) can be corrected. [Total maximum byte: 5 byte × 6 ( interleave) = 30 byte] If the error of read sector keeps allowable error byte number, correction is performed. However, if error byte exceeds its allowable number, correction may not be performed properly. The mai
ملخص المحتوى في الصفحة رقم 6
This page is intentionally left blank.
ملخص المحتوى في الصفحة رقم 7
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Data loss Mounting Installation 2-5 For MAP series, Reed Solomon codes are applied for their ECC. The sector-data is divided into 6
ملخص المحتوى في الصفحة رقم 8
Important Alert Items Task Alert message Page Mounting Installation Damage 5-5 1. When dismounting the drive which is mounted on the system while power is supplied to it. • The drive to be dismounted must be separated from the loop. Dismounting the drive which is not separated from the loop may cause an unexpected error. • If the drive is not separated from the loop, issue an LPB to the drive from the initiator in a primitive sequence of the order set. • It is recommended to stop the spindle mo
ملخص المحتوى في الصفحة رقم 9
Important Alert Items Task Alert message Page Caution 6-6 1. Always ground yourself with a wrist strap connected to ground before handling. ESD (Electrostatics Discharge) may cause the damage to the device. 2. Do not remove a PCA. This operation is required to prevent unexpected or unpredictable operation. 3. Do not use a conductive cleaner to clean a disk drive assembly. Damage 6-6 Never open the disk enclosure in the field. Opening the disk enclosure in the field may cause an irreparable fa
ملخص المحتوى في الصفحة رقم 10
This page is intentionally left blank.
ملخص المحتوى في الصفحة رقم 11
Manual Organization PRODUCT/ 1. General Description MAINTENANCE MANUAL 2. Specifications 3. Data Format (This manual) 4. Installation Requirements 5. Installation 6. Diagnostics and Maintenance 7. Error Analysis Fibre Channel 1. Command Processing Interface 2. Data Buffer Management Specifications 3. Command Specification 4. Sense Data and error Recovery Procedure 5. Disk Medium Management C141-E163 ix
ملخص المحتوى في الصفحة رقم 12
This page is intentionally left blank.
ملخص المحتوى في الصفحة رقم 13
REFERENCED STANDARDS The product specifications and functions described in this manual conform to the following ANSI (*1) standards: Document number Title NCITS TR-19 FIBRE CHANNEL PRIVATE LOOP SCSI DIRECT ATTATH (FC-PLDA) ANSI X3.230-1994 FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE (FC-PH) ANSI X3.297-1996 FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE-2 (FC- PH-2) ANSI X3.272-199X FIBRE CHANNEL ARBITRATED LOOP (FC-AL) ANSI X3.269-199X FIBRE CHANNEL PLOTOCOL FOR SCSI (SCSI-FCP) *1 ANSI = Ame
ملخص المحتوى في الصفحة رقم 14
This page is intentionally left blank.
ملخص المحتوى في الصفحة رقم 15
CONTENTS CHAPTER 1 General Description ..................................................................1-1 1.1 Standard Features ....................................................................................1-2 1.2 Hardware Structure .................................................................................1-5 1.3 System Configuration..............................................................................1-7 CHAPTER 2 Specifications...........................................
ملخص المحتوى في الصفحة رقم 16
Contents 4.1.1 External dimensions ..............................................................................4-1 4.1.2 Mounting ...............................................................................................4-3 4.1.3 Notes on mounting ................................................................................4-3 4.2 Power Supply Requirements ...................................................................4-7 4.3 Connection Requirements ................................
ملخص المحتوى في الصفحة رقم 17
Contents 6.2.4 Revision numbers..................................................................................6-9 6.2.5 Tools and test equipment ....................................................................6-10 6.2.6 Tests ....................................................................................................6-10 6.3 Operation Check....................................................................................6-12 6.3.1 Initial seek operation check ...................
ملخص المحتوى في الصفحة رقم 18
Contents Illustrations Figures Figure 1.1 FC model drives outer view ......................................................... 1-5 Figure 1.2 Disk/head configuration............................................................... 1-6 Figure 1.3 Example of FC-AL system configuration.................................... 1-7 Figure 3.1 Cylinder configuration ................................................................. 3-2 Figure 3.2 Spare area in cell ............................................
ملخص المحتوى في الصفحة رقم 19
Contents Tables Table 2.1 Model names and order numbers..................................................2-1 Table 2.2 Function specifications .................................................................2-2 Table 2.3 Environmental/power requirements..............................................2-4 Table 3.1 Zone layout and track capacity .....................................................3-3 Table 3.2 Format capacity.........................................................................
ملخص المحتوى في الصفحة رقم 20
This page is intentionally left blank.
