Bunn IMIX 5S دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

IMIX-3S
IMIX-5S
INSTALLATION & OPERATING MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
38526.0000B 04/06 ©2005 Bunn-O-Matic Corporation www.bunnomatic.com

ملخص المحتوى في الصفحة رقم 2

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years parts and 1 year labor. 4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: parts and labor for 3 years or 30,000 po

ملخص المحتوى في الصفحة رقم 3

USER NOTICES The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels. ! WARNING Fill water tank before turning - on - thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. 00656.0000 Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE, OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL BEFO

ملخص المحتوى في الصفحة رقم 4

INITIAL SET-UP 1. Apply the four non-skid pads from the parts box to the bottom of the legs. 2. Remove the drip tray assembly, drip tray bracket, and splash panel assembly from the parts box. 3. Place a set of key holes in the drip tray bracket over the lower two screws in the panel below the hopper ac- cess door; push down gently and tighten screws. 4. Place the set of key holes in the splash panel over the upper two screws and position so the screws are between the holes. ELECTRICAL REQUIREME

ملخص المحتوى في الصفحة رقم 5

INITIAL FILL & HEAT CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Turn-on the water supply and connect the dispenser to the power source. 2. Water will automatically flow into the tank to the proper level and then shut-off. This will take less than five minutes. 3. When the tank is full of water, open the front door and place the heater switch in the “ON” (lower) position. A tank full of cold

ملخص المحتوى في الصفحة رقم 6

CLEANING Refer to the decal on the rear of the dispenser door for cleaning recommendations and procedures. The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur- faces on Bunn-O-Matic equipment. Do NOT clean this equipment with a water jet device. ADJUSTMENTS The beverage solenoid is preset to dispense approximately 9/10 ounce per second (26 mL/sec). This amount can be adjusted: 1. Disconnect the dispenser from the power source. 2. Remove

ملخص المحتوى في الصفحة رقم 7

ELECTRICAL WIRING DIAGRAM IMIX-3S LEFT RIGHT LAMP LAMP 36526 040706 7

ملخص المحتوى في الصفحة رقم 8

ELECTRICAL WIRING DIAGRAM IMIX-5S 1 6 PNK 1 1 6 1 4 RED/WHI BLU/WHI GRY 1 "RINSE" #1-3 L.E.D. PNK 1 4 1 4 RED/GRN ORN/RED GRY 1 "RINSE" #4 & 5 L.E.D. 1 2 3 4 5 WHI/RED BLK/WHI WHI/RED RED WHI/RED ORN WHI/RED GRN/WHI WHI/RED BLU BLK WHI/BLK BLK RED/BLK BLK ORN/BLK BLK BLK BLU/BLK GRN/BLK LEFT LAMP RIGHT ASSY. LAMP ASSY. 36526 102705 8 SCHEMATIC WIRING DIAGRAM IMIX-5S L1 N GRN WHI J4-1 CONTROL BRN/BLK TANK HEATER LIMIT C THERMOSTAT WHI SWITCH THERMOSTAT K O TANK HEATER BLK BLK-16 BLK-16 B