Vision Fitness 2200 HRC دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

R2200/2200 HRC
ASSEMBLY INSTRUCTIONS
To avoid possible damage to this Fitness Cycle,
please follow these assembly instructions.
Carefully remove all its parts from the box,
lay them out and review the parts list.
If any parts are missing, please call 1-800-335-4348, Ext 12
Before proceeding, find your Fitness Cycle’s serial number,
located on the underside of main frame, and enter here:
______________________________
Refer to this number when calling for service.
IT ALL STARTS WITH A VISION

ملخص المحتوى في الصفحة رقم 2

R2200 Parts Diagram

ملخص المحتوى في الصفحة رقم 3

R2200 Parts VISION FITNESS R2200 Parts Description Part # Description Count Dimensions Front Wheel Parts #148 Front Foot Wheel Axle 1 #149 Front Transport Wheels 2 #150 Inside Wheel Washers 2 #185 Outside Wheel Washers 2 #182 Wheel Attachment Bolts 2 20mm L x 8mm D Rear Rail Support Bars #106 Rear Foot Assembly 1 #182 Rear Foot Attachment Bolts 4 20mm L x 8mm D #91 Rear Foot Frame Extension 1 #182 Frame Extension Bolts 4 20mm L x 8mm D #96 Seat Rail Support Post 1 #186 Support Post Bolts-Bottom

ملخص المحتوى في الصفحة رقم 4

R2200 Assembly NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. Step 1 • Front Wheel Assembly 1: Slide the Front Foot Axle (148) through the Front Foot Nylon Sleeves (147). 2: Place the Inside Wheel Washers (150) on the Front Foot Axle (148). 3: Slip the Front Transport Wheels (149) onto the Front Foot Wheel Axle and secure them with the outside Wheel Washers (185) and the Wheel Attachment Bolts (1

ملخص المحتوى في الصفحة رقم 5

R2200 Assembly Step 3 • Seat Assembly 1: Secure the Seat Mount Handlebars (110) to the Seat Frame (115) with four Seat Mount Handlebar Bolts (182). 2: When mounting the Seat Cushion Bottom (136), you have two sets of holes to choose from. Using the rear set of holes is recommended for most people. For a smaller person, you may choose to use the forward set of bolt holes. Mount the Seat Cushion Bottom (136) to the Seat Frame (115) with four of the Seat Cushion Bolts (195) and Seat Cushion B

ملخص المحتوى في الصفحة رقم 6

R2200 Assembly Step 5 • Pedals 1: Identify the left and right Pedals (152) and the left and right Pedal Straps (199). Attach the correct straps to each pedal, then thread each Pedal into the correct left and right crank arms and tighten. NOTE: It is very important to FULLY TIGHTEN each pedal. Failure to do so will result in loosening and NOISE. Step 6 • Console Mast 1: Unfold the Console Cable (75) that is folded into the Frame Console Mast bracket. Straighten this cable and remove any kinks

ملخص المحتوى في الصفحة رقم 7

R2200 Final Assembly Step 7 • Console 1: Plug the Console Cable (75) into the Console (153). The cable Connectors are slotted and will only fit properly one way. DO NOT FORCE the connection. 2: Mount the Console (153) to the Console Mast (101) using the four Console Attachment Bolts (197). Make sure you DO NOT PINCH the Console Cable between the Console and the Console Mast. 3: Plug the Power Supply Cord into the receptacle located at the base of the Fitness Cycle below the Seat rail. Plug t

ملخص المحتوى في الصفحة رقم 8

621-D East Lake Street P.O. Box 280 Lake Mills, WI 53551 (920) 648-4090