ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY PLATINUM
Safety Notice
Olympic Cage
Hardware Identifier
MP-12.0
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MP-12.0
Retain This
Manual for
Reference
07-19-06
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitne
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 8 EXPLODED DIAGRAM.........................................................
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a
ملخص المحتوى في الصفحة رقم 4
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Floor Stabilizer, Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
ملخص المحتوى في الصفحة رقم 5
HARDWARE PACK 4
ملخص المحتوى في الصفحة رقم 6
HARDWARE PACK 5
ملخص المحتوى في الصفحة رقم 7
HARDWARE PACK 6
ملخص المحتوى في الصفحة رقم 8
HARDWARE PACK 7
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Main Frame (#32) to the Rear Floor Stabilizer (#33). Secure it with two M10 x 3 ½” Allen Bolts (#90), one 2 ¾” x 2” Bracket (#39), and two ∅ ¾” Washers (#80). B.) Thread a T-shaped Lock Pin (#42) into the bracket on the Main Frame. C
ملخص المحتوى في الصفحة رقم 10
STEP 2 (See Diagram 2) A.) Attach the Seat Bracket (#36) to the pivot on the Main Frame (#32). Attach the two Backrest Supports (#38) to the Seat Bracket. Align the holes and secure them together with one M12 x 8 ½” Allen Bolt (#89), two Ø 1” Washers (#81), and one M12 Aircraft Nut (#83). Insert the Seat Bracket into the open slot on the Main Frame and use the T-shaped Lock Pin to secure at desired height. B.) Attach the Incline Support (#37) to the middle side-holes on the Backrest Su
ملخص المحتوى في الصفحة رقم 11
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#45) onto the two Backrest Supports (#38). Secure it with four M8 x 1 5/8” Allen Bolts (#99) and ∅ 5/8” Washers (#79). B.) Place the Seat (#44) onto the Seat Bracket (#36). Secure it with four M8 x 1 5/8” Allen Bolts (#99) and ∅ 5/8” Washers (#79). DIAGRAM 3 10
ملخص المحتوى في الصفحة رقم 12
STEP 4 (See Diagram 4) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach the Right Support (#3) to an Upright Beam (#1). Secure it with one M10 x 3 ½” Carriage Bolt (#86), ∅ ¾” Washer (#80) and M10 Aircraft Nut (#82). Attach the Side Support (#4) to the Upright Beam. Secure it with two M10 x 5/8” Allen Bolts (#98) and ∅ ¾” Washers (#80). Attach the other end to the Right Support. Repeat the same step to install the Left Support (#2) and Side Support to another U
ملخص المحتوى في الصفحة رقم 13
STEP 5 (See Diagram 5) A.) Attach the Rear Vertical Frame (#6) onto the Rear Base (#16). Secure it with two M10 x 2 ¾” Carriage Bolts (#85) from the bottom, two ∅ ¾” Washers (#80) and two M10 Aircraft Nuts (#82) on the top. Slide the Sliding Weight Post (#11) onto the Rear Vertical Frame from the top. B.) Place the Rear Base (#16) in between the two Rear Left & Right Stabilizers (#7 & #8). Attach the Front Vertical Frame (#9) onto the Rear Base (#16). Align the holes and secure them
ملخص المحتوى في الصفحة رقم 14
DIAGRAM 5 13
ملخص المحتوى في الصفحة رقم 15
CABLE LOOP DIAGRAM 14
ملخص المحتوى في الصفحة رقم 16
STEP 6 (See Diagram 6) A.) Attach a Pulley (#58) to the front opening on the Upper Frame (#10). Attach the 133” Upper Cable (#29) to the Pulley. Secure the Pulley with one M10 x 2 ½” Allen Bolt (#93), two Ø 1” x 5/8” Pulley Bushings (#77), and one M10 Aircraft Nut (#82). Make sure the ball stopper on the Cable is underneath the Upper Frame. B.) Draw the Cable over the Pulley along the Upper Frame towards the back of the machine to the open bracket on the Upper Frame. C.) Attach a Pu
ملخص المحتوى في الصفحة رقم 17
DIAGRAM 6 16
ملخص المحتوى في الصفحة رقم 18
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 241” High/Low Cable (#31) to the Sliding Pulley Bracket (#17). Attach two Small Pulleys (#59) to the Sliding Pulley Bracket. Secure each Small Pulley with one M10 X 1 ¾” Allen Bolt (#94), two ∅ ¾” Washers (#80), and one M10 Aircraft Nut (#82). B.) Draw the Cable in between the two Pulleys then upward to the opening on top of the Front Vertical Frame (#9). C.) Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Alle
ملخص المحتوى في الصفحة رقم 19
DIAGRAM 7 18
ملخص المحتوى في الصفحة رقم 20
STEP 8 (See Diagram 8) A.) Insert the Left & Right Bar Catches (#12 & #13), Left & Right Safety Catches (#14 & #15) to the selected holes on the Upright Beams. B.) Attach two Olympic Sleeves (#52) to the Sliding Weight Post (#11). C.) Attach four Olympic Sleeves (#52) to the Weight Posts (#20). Attach a Spring Clip (#53) to each Olympic Sleeve. DIAGRAM 8 19
