ملخص المحتوى في الصفحة رقم 1
MODEL W1783
FLOORING NAILER
OWNER'S MANUAL
(FOR MACHINES MANUFACTURED SINCE 2/07)
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED NOVEMBER, 2009 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9627TS Printed in China
ملخص المحتوى في الصفحة رقم 2
This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installa- tion in a safe environment, personnel training and usag
ملخص المحتوى في الصفحة رقم 3
Model W1783 (Mfg. Since 2/07) SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper acciden
ملخص المحتوى في الصفحة رقم 4
Model W1783 (Mfg. Since 2/07) Safety Instructions for Pneumatic Tools 17. DISCONNECT TOOLS before 10. USE PROPER AIR HOSE for the servicing, changing accessories, or tool. Make sure your air hose is in moving to another location. good condition and is long enough 18. DO NOT OVERREACH. Keep proper to reach your work without footing/balance at all times. stretching. 19. USE THE RECOMMENDED 11. WEAR PROPER APPAREL. Do ACCESSORIES. Consult owner’s not wear loose clothing, gloves, manual
ملخص المحتوى في الصفحة رقم 5
Model W1783 (Mfg. Since 2/07) Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work puncturing your hand or fingers. without stretching. However, an overly long air hose in the work 2. COMBUSTIBLE GASES: Never area may be a tripping hazar
ملخص المحتوى في الصفحة رقم 6
Model W1783 (Mfg. Since 2/07) INTRODUCTION Woodstock Technical Tool Data Support Nail Length ................................1 "–2" Magazine Capacity ................. 100 Nails The Model W1783 Flooring Nailer has 1 Air Inlet ................................ ⁄4" NPT been specially designed to provide many 1 Nailer Weight ....................... 11 ⁄3 lbs. years of trouble-free service. Close atten- 1 Hammer Weight ......................2 ⁄2 lbs. tion to detail, ruggedly built parts and a Oper
ملخص المحتوى في الصفحة رقم 7
Model W1783 (Mfg. Since 2/07) Compressed Air System The Model W1783 is designed to be operated at 70-110 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as Exceeding the maximum permissible needed for satisfactory results. operating pr
ملخص المحتوى في الصفحة رقم 8
Model W1783 (Mfg. Since 2/07) SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1783. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully. O
ملخص المحتوى في الصفحة رقم 9
Model W1783 (Mfg. Since 2/07) OPERATIONS Loading Operating When replacing nails in your Model If you have not read the safety W1783, follow these guidelines: instructions in this manual, do not operate the nailer. Nails .................... L-Shaped Cleat Nails Length: .................................... 1"–2" Before you operate your nailer, place five Capacity: ................................... 100 to six drops of the included oil into the quick connect fitting where the nailer 1 1 Note
ملخص المحتوى في الصفحة رقم 10
Model W1783 (Mfg. Since 2/07) NOTICE DO NOT use the nailer to position the Never hit the whack cap of the nailer flooring strip. Doing so will damage multiple times to drive the nail the nailer and possibly the flooring into the wood. If necessary, use a strip. hammer and nail punch to drive the nail in. Failure to heed this warning Note: If you are using pre-finished could cause a nail jam or a ricochet, flooring material, test the nailer on a and serious personal injury. sample str
ملخص المحتوى في الصفحة رقم 11
Model W1783 (Mfg. Since 2/07) 3. The jammed nail should be visible in 7. Throw the damaged nail away and the discharge area. insert a new nail stick that only contains clean, undamaged nails. DO — If the jammed nail can be removed NOT use dirty or damaged nails! with needle nose pliers, do so and continue to Step 7. Replacing Pistons/ O-Rings — If you cannot remove the jammed nail, then continue with Step 4. Under heavy use, the piston or O-rings may wear out. Replacement is quick and 4.
ملخص المحتوى في الصفحة رقم 12
Model W1783 (Mfg. Since 2/07) 4. Use a 5mm hex wrench to remove the 7. Remove the four cap screws and lock four cap screws that secure the base washers from the cylinder cover, and to the nailer body (see Figure 6). remove it from the nailer body. 8. Remove the three cap screws from the top of the plunger (see Figure 9). Plunger Figure 6. Cap screws that secure the base to the nailer body. Cap Screw 5. Carefully slide the base from the Figure 9. Plunger and cap screws. nailer body, and remo
ملخص المحتوى في الصفحة رقم 13
Model W1783 (Mfg. Since 2/07) CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Place two to six drops of pneumatic tool assembly of the nailer. Always be sure oil in the nailer air inlet (as shown in that the nailer is dry before using it Figure 11) every 2 hours of continuous again. use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. Do not allow dust, chips, sand, etc. into the air connectors or into the body Another option to manu
ملخص المحتوى في الصفحة رقم 14
Model W1783 (Mfg. Since 2/07) PARTS BREAKDOWN 35 37 33 31 38 30 29 32 28 63 25 39 43 41 64 27 42 19 24 26 40 23 38 37 44 22 52 18 45 51 17 15 46 44 16 14 53 54 47 13 12 48 55 11 49 26 10 50 34 5 9 60 8 4 65 56 57 3 61 59 58 7 62 69 1 6 68 70 67 66 -12-
ملخص المحتوى في الصفحة رقم 15
Model W1783 (Mfg. Since 2/07) PARTS LIST REFPART # DESCRIPTION REFPART # DESCRIPTION 1 X1783001 CYLINDER 38 XPW01M FLAT WASHER 8MM 3 X1783003 BUMPER 39 X1783039 L-BOLT 4 XPORP050 O-RING 49.7 X 3.5 P50 40 X1783040 STOPPER 5 X1783005 DRIVER 41 XPS38M PHLP HD SCR M4-.7 X 10 6 XPRP07M ROLL PIN 6 X 20 42 X1783042 MAGAZINE SEAT 7 XPSS31M SET SCREW M5-.8 X 8 43 X1783043 MAGAZINE END CAP 8 X1783008 PISTON POLE 44 XPLN01M LOCK NUT M4-.7 9 X1783009 PISTON HEAD 45 X1783045 PUSHER SEAT 10 XPORP012-5O-RING
ملخص المحتوى في الصفحة رقم 16
Model W1783 (Mfg. Since 2/07) Troubleshooting Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in plunger/cylinder 1. O-rings must be replaced & whack cap area. housing are damaged. operation checked. Air leaking between 1. Loose screws in housing. 1. Tighten screws. housing and hose 2. Damaged O-ring. 2. Replace O-ring 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. 1. Replace damaged seals. housing and cap. Tool skips nai
ملخص المحتوى في الصفحة رقم 17
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email___________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
ملخص المحتوى في الصفحة رقم 18
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOx 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
ملخص المحتوى في الصفحة رقم 19
WARRANTY AND RETURNS Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc. will repair or replace, at its expense and at its option, the
ملخص المحتوى في الصفحة رقم 20
