ملخص المحتوى في الصفحة رقم 1
®
TURN-NADO EVS LATHE w/DRO
MODEL SB1042PF 21" X 60" MODEL SB1059F 18" X 40"
MODEL SB1043PF 21" X 80" MODEL SB1060PF 18" X 60"
MODEL SB1045PF 21" X 120" MODEL SB1061PF 18" X 80"
OWNER'S MANUAL
© August, 2011 by South Bend Lathe Co. For Machines Mfg. Since 3/11
ملخص المحتوى في الصفحة رقم 2
Scope of Manual This manual helps the reader understand the machine, how to prepare it for operation, how to control it during operation, and how to keep it in good working condition. We assume the reader has a basic understanding of how to operate this type of machine, but that the reader is not familiar with the controls and adjustments of this specific model. As with all machinery of this nature, learning the nuances of operation is a process that happens through training and experience. I
ملخص المحتوى في الصفحة رقم 3
Table of Contents INTRODUCTION .................................................... 3 Installation & Removal Devices ........................37 About This Machine .............................................3 Chuck Installation .............................................38 Foreword ............................................................. 3 Registration Marks ............................................ 39 Capabilities ......................................................... 3 Chuck Remo
ملخص المحتوى في الصفحة رقم 4
Headstock & Gearbox Threading Controls .......... 59 Electrical Box Wiring.........................................96 Apron Controls .................................................. 60 Electrical Box .....................................................97 Thread Dial ....................................................... 61 Spindle Motor .....................................................98 Thread Dial Chart ............................................. 61 Oil Pump Motor & Pressure Sensor .
ملخص المحتوى في الصفحة رقم 5
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION About This Machine Foreword Features "The screw cutting engine lathe is the oldest and As the name implies, these lathes feature EVS most important of machine tools and from it all (Electronic Variable Speed) spindle control other machine tools have been developed. It was to "dial in" the perfect cutting speed for the the lathe that made possible the building of the operation. One of four spindle speed ranges is steamboat, the
ملخص المحتوى في الصفحة رقم 6
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION General Identification G E D H K I J C L F B A M N O T S U R P Q Figure 1. General identification (Model SB1043PF shown). A. Quick-Change Gearbox Controls L. Tailstock w/MT#5 Quill B. Headstock Controls M. Leadscrew C. D1-8 Camlock MT#7 Spindle N. Feed Rod D. EVS Control Panel O. Spindle Rod E. Chuck Guard w/Safety Switch P. Rod Support (SB1043PF/-45PF/-61PF only) F. 4-Way Tool Post Q. Chip Drawer G. Halogen Work Lamp R. Safety Foot
ملخص المحتوى في الصفحة رقم 7
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Headstock Controls Controls & Components D Refer to Figures 2–9 and the following E descriptions to become familiar with the features C and basic controls of this lathe. This knowledge will be necessary to properly set up the lathe for the test run and spindle break-in. B F To reduce the risk of serious injury when using A this machine, read and understand this entire manual before beginning any lathe operations. Master P
ملخص المحتوى في الصفحة رقم 8
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Control Panel Carriage P H I G L Q O T N S U J M K R V W Figure 4. Control panel. G. Tachometer Display: Displays the current Y X spindle speed in RPM's. H. Spindle Speed Dial: Electronically varies Figure 5. Carriage controls. the spindle speed within the selected spindle speed range. M. Carriage Handwheel: Moves the carriage along the bed. Can be disengaged during I. Power Light: Illuminates when lathe controls power fee
ملخص المحتوى في الصفحة رقم 9
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION U. Thread Dial and Chart: Dial indicates when Tailstock to engage the half nut during threading operations. Chart indicates on which thread dial reading to engage the half nut for AB specific inch thread pitches. AC AD AA V. Spindle Lever: Starts, stops and reverses direction of spindle rotation. AF W. Feed ON/OFF Lever: Engages/disengages AE power feed. X. Apron Feed Direction Knob: Changes direction of carriage or the cros
ملخص المحتوى في الصفحة رقم 10
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Safety Foot Brake This lathe is equipped with a foot brake (see AG Figure 9) to quickly stop the spindle instead of allowing it to coast to a stop on its own. Pressing the foot brake while the spindle is ON also cuts AH power to the motor. After the foot brake is used, the spindle lever must be returned to the OFF (middle) position to reset the spindle switches before spindle rotation can be re-started. AJ AI Spindle Lever F
ملخص المحتوى في الصفحة رقم 11
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Product Specifications P.O. Box 2027, Bellingham, WA 98227 U.S.A. © South Bend Lathe Co. www.southbendlathe.com MODEL SB1042PF, SB1043PF, SB1045PF 21" EVS TOOLROOM LATHE w/DRO Model Number SB1042PF SB1043PF SB1045PF Product Dimensions Weight 5830 lbs. 6600 lbs. 8140 lbs. Width (side-to-side)/Depth 1 1 1 1 3 1 110 ⁄2" x 27" x 62 ⁄4" 130 ⁄4" x 27" x 62 ⁄4" 169 ⁄4" x 27" x 62 ⁄4" (front-to-back)/Height 3 3 3 3 Foot Print (Width/Dept
ملخص المحتوى في الصفحة رقم 12
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Model Number SB1042PF SB1043PF SB1045PF Main Motor Type TEFC Induction Horsepower 12.5 HP Voltage 440V Phase 3-Phase Amps 18A Speed 0–3000 RPM Cycle 60 Hz Power Transfer V-Belt & Gear Bearings Shielded & Permanently Sealed Coolant Motor Type TEFC Induction 1 Horsepower ⁄8 HP Voltage 440V Phase 3-Phase Amps 0.23A Speed 3450 RPM Cycle 60 Hz Power Transfer Direct Drive Bearings Shielded & Permanently Sealed Lubrication Motor Type TEFC
ملخص المحتوى في الصفحة رقم 13
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Model Number SB1042PF SB1043PF SB1045PF Headstock Information Spindle Bore 3.15 in. Spindle Taper MT#7 Number of Spindle Speeds Variable Range of Spindle Speeds 18–1800 RPM Spindle Type D1-8 Camlock Spindle Bearings Tapered Roller Tailstock Information Tailstock Quill Travel 6.5 in. Tailstock Taper MT#5 Tailstock Barrel Diameter 3 in. Threading Information Number of Longitudinal Feeds 15 Range of Longitudinal Feeds 0.0015–0.0400 in
ملخص المحتوى في الصفحة رقم 14
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Model Number SB1042PF SB1043PF SB1045PF Construction Headstock Cast Iron Headstock Gears Flame-Hardened Steel Bed Meehanite Castings with Induction-Hardened Ways Stand Cast Iron Paint Urethane Other Country of Origin Taiwan (Some Components Made in USA & Germany) Warranty 1 Year Serial Number Location ID Label on Front of Headstock Assembly Time Approximately 1 Hour Sound Rating at Idle 69 dB -12-
ملخص المحتوى في الصفحة رقم 15
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Product Specifications P.O. Box 2027, Bellingham, WA 98227 U.S.A. © South Bend Lathe Co. www.southbendlathe.com MODEL SB1059F, SB1060PF, SB1061PF 18" EVS TOOLROOM LATHE w/DRO Model Number SB1059F SB1060PF SB1061PF Product Dimensions Weight 4400 lbs. 5170 lbs. 5940 lbs. Width (side-to-side)/Depth 3 1 1 1 1 1 90 ⁄4" x 27" x 62 ⁄4" 110 ⁄2" x 27" x 62 ⁄4" 130 ⁄4" x 27" x 62 ⁄4" (front-to-back)/Height 1 3 1 3 3 Foot Print (Width/Depth
ملخص المحتوى في الصفحة رقم 16
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Model Number SB1059F SB1060PF SB1061PF Main Motor Type TEFC Induction Horsepower 10 HP 12.5 HP Voltage 440V Phase 3-Phase Amps 16A 18A Speed 0–3000 RPM Cycle 60 Hz Power Transfer V-Belt & Gear Bearings Shielded & Permanently Sealed Coolant Motor Type TEFC Induction 1 Horsepower ⁄8 HP Voltage 440V Phase 3-Phase Amps 0.23A Speed 3450 RPM Cycle 60 Hz Power Transfer Direct Drive Bearings Shielded & Permanently Sealed Lubrication Motor
ملخص المحتوى في الصفحة رقم 17
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Model Number SB1059F SB1060PF SB1061PF Headstock Information Spindle Bore 3.15 in. Spindle Taper MT#7 Number of Spindle Speeds Variable Range of Spindle Speeds 18–1800 RPM Spindle Type D1-8 Camlock Spindle Bearings Tapered Roller Tailstock Information Tailstock Quill Travel 6.5 in. Tailstock Taper MT#5 Tailstock Barrel Diameter 3 in. Threading Information Number of Longitudinal Feeds 15 Range of Longitudinal Feeds 0.0015–0.0400 in.
ملخص المحتوى في الصفحة رقم 18
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes INTRODUCTION Model Number SB1059F SB1060PF SB1061PF Construction Headstock Cast Iron Headstock Gears Flame-Hardened Steel Bed Meehanite Castings with Induction-Hardened Ways Stand Cast Iron Paint Urethane Other Country of Origin Taiwan (Some Components Made in USA & Germany) Warranty 1 Year Serial Number Location ID Label on Front of Headstock Assembly Time Approximately 1 Hour Sound Rating at Idle 69 dB -16-
ملخص المحتوى في الصفحة رقم 19
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes SAFETY Understanding Risks of Machinery Operating all machinery and machining equipment can be dangerous or relatively safe depending on how it is installed and maintained, and the operator's experience, common sense, risk awareness, working conditions, and use of personal protective equipment (safety glasses, respirators, etc.). The owner of this machinery or equipment is ultimately responsible for its safe use. This responsibility includes
ملخص المحتوى في الصفحة رقم 20
® For Machines Mfg. Since 3/11 Turn-Nado EVS Lathes SAFETY Entanglement: Loose clothing, gloves, neckties, Chuck Keys or Adjusting Tools: Tools used to jewelry or long hair may get caught in adjust spindles, chucks, or any moving/ moving parts, causing entanglement, rotating parts will become dangerous amputation, crushing, or strangulation. projectiles if left in place when the machine Reduce this risk by removing/securing is started. Reduce this risk by developing these items so they canno