ملخص المحتوى في الصفحة رقم 1
BEHIND SNOWTIIROWER
7/22E
Mfg. No. 1692615
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
Table of Contents HANDLE & CONTROLS ............................................................. 2 ENGINE .......................................................................... 4 FRAME ........................................................................... 6 AUGER DRIVE ..................................................................... 8 AUGER HOUSING & CHUTE ........................................................ 10 WHEELS & TRACTION DRIVE ..........................................
ملخص المحتوى في الصفحة رقم 4
Handle & Controls Apply adhesive NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 43 -3 2
ملخص المحتوى في الصفحة رقم 5
All Models Handle & Controls REF. PART NO. NO. QTY. DESCRIPTION 1 121175 1 LINER, Rod Guide 2 176934 1 GRIP 3 916168 2 PIN, Roll, 1/8x 3/4 4 1916964 1 LOCKWASHER, l/4 5 1923341 2 CAPSCREW, Hex, 1/4-20 x 3/4 6 1960093 1 PALNUT 7 1668188 2 GEAR, Universal 8 1668189 1 ROD, Chute Control 9 1674177 1 HANDLE PANEL, Upper 10 1674178 1 HANDLE PANEL, Lower 11 1674329 1 SPROCKET, Chute 12 1674580 2 SPACER 1 13 1676252 ARM, Shift Assy. - 5 HP Only 14 1676253 1 SPRING (Qty. 2 on 7 HP) 15 1676325 1 SUPPORT,
ملخص المحتوى في الصفحة رقم 6
Engine 18 NOTE A: Position Belt Guides 1/16" to 1/8" from belt when idler arm is engaged. .-&See Note A XT 555 Assembly View Torque to 10-14 ft. Ibs. (2 places) I position Ref. No. 11 1/ I flush, with hub toward 3b engine. Install with the hub facing engine on 755 & 7/22E. Install with the hub away from engine on 555. Engine Pulley - 6,13 NOTE: Unless noted otherwise, use the standard hardware torque specification chart.
ملخص المحتوى في الصفحة رقم 7
All Models Engine PART REF. NO.’ NO. QTY. DESCRIPTION * 1 1 ENGINE, Tecumseh * 1 SWITCH ASSY., Ignition w/keys 2 3 905121 1 KEY, Woodruff, 1/8 x 5/8 4 1 KEY, Sq., 3/16x 3/16 x 1 905850 1 GROUND WIRE 5 1667700 6 1674308 1 BELT, Traction Drive (5 HP only) 1 BELT, Auger Drive 7 1674312 1674325 1 PULLEY, Idler (5 HP only) 8 9 1675339 1 NUT, Hex, Lock, 5/16-18 (5 HP only) 10 1674328 1 PULLEY, Engine 11 1677924 1 GUIDE, Belt 1677925 1 GUIDE, Belt (5 HP only) 12 1 BELT, Traction Drive (7 HP only) 13 16
ملخص المحتوى في الصفحة رقم 8
A-‘*1312 NOTE A: Position Belt Guides 1/16" to 1/8 from Belt when Idler Arm is engaged. 35 -%i@$ 2 Note A See Handle Group P ’ '16 8 SeeNoteAHi7 p / 38 Adjust Shift Guide (Ref. 19) to obtain proper 3 neutral position. NOTE B: Position Idler Pulleys (Ref. Nos. 25 & 8) to outside end of slot. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 6
ملخص المحتوى في الصفحة رقم 9
All Models Frame REF. PART NO. NO. QTY. DESCRIPTION 1 174870 1 SPACER 2 916169 3 PIN, Roll 3 925160 2 RIVET 4 1608310 2 SPACER (7 HP only) 5 1611743 1 FRAME 6 1668477 1 PULLEY, Idler, Auger 7 1673911 1 SPRING, Brake Return 8 1674297 1 COVER, Belt 1 9 1674316 IDLER ARM & BRAKE ASSY. (Incl. Ref. Nos. 21 & 3) 10 1674315 1 GUIDE, Belt 11 1674318 1 IDLER ARM ASSY., Traction (5 HP only) 12 1674320 2 ROD, Idler 13 1675112 1 MOUNTING PLATE, Transmission 14 1675114 1 SUPPORT, Transmission 15 1676210 1 SP
ملخص المحتوى في الصفحة رقم 10
Auger Drive Hub of pulley to Torque to 30-34 ft. lbs face auger. 1 14 134 **- -. 16 18-21 ft. Ibs. Ll 12 6 Locate puliey so that centerline is 1-15/16 D from rear of impeller @!A housing. Auger assy. stamped "R". Auger assy. stamped "L". / Use 1 or 2 washer as required to eliminate side-to-side play of auger in housing. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 8
ملخص المحتوى في الصفحة رقم 11
All Models Auger Drive REF. PART NO. NO. QTY. DESCRIPTION 1 905123 2 KEY, Woodruff, 3/1 6 x 3/4 2 917673 1 PLUG, Pipe, 1/8-NPT 3 918312 1 KEY, Woodruff 4 921133 2 GREASE FITTING 5 927794 2 RING, Retaining 1 PIN, Drivelok, 3/16 x 1 -1/2 6 936098 7 1611784 1 GASKET 1 8 1611789 SEAL, Oil * 9 1611793 1 GEAR CASE ASSY., LH (Incl. Ref. No. 20, Qty. 1) *10 1611794 1 GEAR CASE ASSY., RH (Incl. Ref. No. 20) 11 1611795 1 IMPELLER ASSY. 12 1666424 1 BUSHING 13 1666425 1 BUSHING 14 1668105 1 COLLAR, Thrust
ملخص المحتوى في الصفحة رقم 12
Auger, Housing & Chute ~ 13 Must be assembled with no gap between deflector and chute when tipped completely forward. 25 4 Coat top and bottom of 12 chute ring with grease. \J See page 18 for’ housing extension. Mounts to underside ’ of housing. NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 10
ملخص المحتوى في الصفحة رقم 13
All Models Auger, Housing & Chute REF. PART NO. NO. QTY. DESCRIPTION 1 108202 1 BEARING, Ball *2 177434 2 SKID 3 1611746 1 AUGER HOUSING END, LH 4 1611747 1 AUGER HOUSING END, RH 5 1611798 1 AUGER HOUSING ASSY. 6 1665982 1 RETAINER, Bearing 7 1666001 2 BUSHING 8 1666613 2 HOLD DOWN, Chute 9 1667790 2 SPACER IO 1670578 1 KNOB 11 1675080 1 SCRAPER BLADE 12 1676224 1 CHUTE ASSY. 13 1 1676379 DEFLECTOR 14 1678954 1 GUARD, Chute 15 1916950 4 NUT, Hex, 3/8-16 16 1916965 4 LOCKWASHER, 3/8 17 1917356 5
ملخص المحتوى في الصفحة رقم 14
Wheels & Traction Drive A-**1315 Torque to 14-20 ft. lbs. Torque to 14-20 ft. Ibs. Add 1 to 3 washers per side to minimize axle movement. (Both sides must have equal \ number of washers.) Torque to 18-21 16 ‘ft. Ibs. Install with hub flush with shaft. A n’ NOTE: Coat axle with anti-sieze compound before assembling wheels NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 12
ملخص المحتوى في الصفحة رقم 15
All Models Wheels & Traction Drive REF. PART NO. NO. QTY. DESCRIPTION * 1 1 TRANSMISSION 2 172353 2 VALVE STEM & CAP 3 930670 1 KEY, Woodruff, Hi Pro, 3/16 x 3/4 4 1611748 2 SPACER, Wheel 5 1611993 1 AXLE & SPROCKET ASSY. 6 1612001 2 TIRE, Snow Hog Tread, 4.1 O-6 7 1665994 2 PIN, Clevis 8 1666001 2 BUSHING, Wheel 9 1674306 1 PULLEY ASSY., Traction 10 1676381 1 DRIVE CHAIN 11 1714236 2 TIRE & WHEEL ASSY., (Incl. Ref. Nos. 2,6 & 12) 12 1714241 2 WHEEL, (Metallic Grey) 13 1917356 2 LOCKWASHER 14 19
ملخص المحتوى في الصفحة رقم 16
Transmission - Peerless Model 700-027 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. I 14
ملخص المحتوى في الصفحة رقم 17
All Models Transmission - Peerless Model 700-027 REF. PART NO. NO. QTY. DESCRIPTION 1 770061 1 CASE, Transmission 2 772083 1 COVER, Transmission 1 3 776134 SHAFT, Counter 4 776162 1 SHAFT, Output & Brake 5 776203 1 SHAFT, Input 778113A 1 6 BEVEL PINION, Input 7 778121A 1 GEAR, Spur (20 teeth) 1 a 778124A GEAR, Spur (30 teeth) 9 778126A 1 GEAR, Spur (20 teeth) 77/129A 1 10 GEAR, Spur (30 teeth) 11 778137A 1 GEAR, Bevel (42 teeth) 12 778145 1 GEAR, Spur (12 teeth) 778146A 1 GEAR, Spur (37 teeth) 1
ملخص المحتوى في الصفحة رقم 18
Decal & Wrapper Extension 6 SAFETY DECALS Ref. No. 6 Ref. No. 7
ملخص المحتوى في الصفحة رقم 19
All Models Decal & Wrapper Extension Group REF. PART NO. NO. QTY. DESCRIPTION 1 1 DECAL, OPEI 1 I D. PLATE 2 3 1676631* 1 WRAPPER EXT 4 1674170 1 DECAL, Simplicity 1 DECAL, Shift Pattern 5 1676667 6 1676937 1 DECAL, Dash 1 DECAL, Danger, Auger 7 1677485 8 1677488 1 DECAL, Danger, Blower 9 1714107 1 DECAL, Simplicity 755 10 1714108 1 DECAL, Simplicity 555 DECAL, Baker 11 1715066 1 1715067 1 DECAL, Baker 7/22E 12 2 NUT, Hex, 1/4-20 13 1916622 LOCKWASHER, 1/4 14 1916964 2 15 1921958 2 CAPSCREW, 1/4
ملخص المحتوى في الصفحة رقم 20
TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE 2 20%) (Tolerance SIZE SAE GRADE #2 SAE GRADE #5 SAE GRADE #8 0 Q 8 in/lbs in/lbs Mbs Nm. Mbs Nm. Mbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.9 1 O-24 27 3.1 43 4.9 60 6.8 1 O-32 31 3.5 49 5.5 68 7.7 1/4-20 66 7.6 8 10.9 12 16.3 1/4-28 76 8.6 10 13.6 14 19.0 5/1 6-l 8 11 15.0 17 23.1 25 34.0 5/1 6-24 12 16.3 19 25.8 27 34.0 3/8-1 6 20 27.2 30 40.8 45 61.2 3/8-21 23 31.3 35 47.6 50 68.0 7/16-14 30 40.8 50 68.0 70 95.2 7/1 6-20 35 4
