ParaBody 897101 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Serious Steel
897101
WEIGHT STACK OPTION
ASSEMBLY INSTRUCTIONS
ParaBody, Incorporated
14150 Sunfish Lake Boulevard
Ramsey, MN 55303
1-800-328-9714
12/30/96
1
Part Number 6660001

ملخص المحتوى في الصفحة رقم 2

WEIGHT STACK OPTION ASSEMBLY PARTS LIST 897101 SORT Ad~-D COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY ItARDWARE: ITEM .NAM~’,/DESCRIPTION QTY 2 3/8 X 2-:3/4 IN BOLT ......................................................................................................... 1 3/8 X 1-1/2 IN BOLT ......................................................................................................... 2. 1 3/8 IN WASHER ....................................................................................

ملخص المحتوى في الصفحة رقم 3

897101 WEIGHT STACK OPTION ASSEMBLY INSTRUCTIONS; Remove the ].AT BAR from the HIGH PULLEY CABLE, and set aside. Loosen and re,hove the three (3) 3-1/2 X 1 IN PULLEYS from the TOP BOOM WELDMENT of the PROSYSTEM. Detach HIGH PULLEY CAl3LE from the WEIGHT CARRIAGE WELDMENT, remove the CABLE. Loosen and remove TOP BOOM WELDMENT from the PROSYSTEM. Then Remove the WEIGHT CARRIAGE WELDMENT from the PROSYSTEM. Remove the 2 IN SQ END CAPS from the top and bottom of the UPRIGI-/T FRAME WELI)MENT of the

ملخص المحتوى في الصفحة رقم 4

897101 WEIGHT STACK OPTION ASSEMBLY INSTRUCTIONS Insert two (21) GUIDE ROD BUSHINGS into the ROUND TUBES of the PULLEY HOUSING WELDMEI~[T as shown. Also insert one (1) 1-3/4 IN SQ END CAP into the top of the PULLEY HOUSING WELDMENT. 10. Tilt the GUIDE RODS back up to vertical. Insert the PULLEY HOUSING WELDMENT into the UPRIGHT F]~LAME WELDMENT of the PROSYSTEM while at the same time insert the GUIDE RODS into the GLr[DE ROD BUSHINGS of the PULLEY HOUSING WELDMENT as shown. ll. Route the WEIGHT

ملخص المحتوى في الصفحة رقم 5

DESCRIP~ON DASH NO I SHOWN 01 IAS 1-.3/4 IN SQ END CAP ,.3-1/2 X, 1 IN PULLEY (2) 3/1~; IN LOCK NUT (2) 3 X 2 IN END CAP (2) ,3/8 IN FLANGE SPACER (4) PULLEY HOUSING WELOMENT (6659403,) 3/8 X 2-3/4 IN BOLT (2) GUIDE ROD BUSHING (2) --3/8 X 1-1/2 IN BOLT .]/8 IN WASHER WI7GHT STACK WEIGHT STACK PIN UPRIGHT FRAME WELDMENT WEIGHT STACK CUSION (2) #AS,r. WELDMENT (’66,59503) 2 IN SQ END CAP (4) 1/2 IN LOW HEIGHT LOCK NUT BASE

ملخص المحتوى في الصفحة رقم 6

REVISIONS REY DESCRIPTION CHG NO APP’D t TOP BOOM WELDMENT WEIGHT STACK CABLE (’d66010f.) PULLEY BLOCK UPRIGHT FRAME WELDMENT LOW PULLEY CABLE CABLE ROUTING DIAGRAM WEIGHT PLATE BUSHING (2) WEIGHT PLATE (20) WEIGHT STACK LABEL (1-25) DETAIL A TOLERANCES (EXCEPT A:$ NOTED) .PARABODY, INC. DECIMAL RAMSEY, MINNESOTA ASSY INST, 897101 D~W~NO NO. ,scAu~ 1/21 ! S~ZE ANGULAR 66600 ~"~, o~, B