ParaBody 805106 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

I
Serious
805106 FLAT & INCLINE BENCH
ASSEMBLY INSTRUCTIONS
Re~’ision: 09111/97
1
Part # 6706601

ملخص المحتوى في الصفحة رقم 2

IIMPO~~ANT ~OTESl WELCOME TO THE WORLD OF g,,iou, S’,eee: Please note: * Thank you for purchasing the Parabody 805106 FLAT & INCLINE BENCH. Please rea~ these instructions thoroughly and keep them for future, reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-

ملخص المحتوى في الصفحة رقم 3

1/2 X3" I ! 3/8 FIGURE 3 STEP 3: ¯ Snap two 3 X 2" GUIDE INSERTS (15) into the ends ofthe WOLFF SLEEVE (7) =~s-shown in HGURE ¯ In~er~ 3/8" SPRING PIN ASSEMBLY (11) into the spring pin barrel on WOLFF SLEEVE (7) and tighten securely. See FIGURE 3. ¯ Slide one 4" VINYL CAP (17) over the U-PIN (16) as shown in FIGURE ¯ Slide U-PIN (16) through the bushing on WOLFF SLI~.Wv-E (7) and attach with PAL-NUT ¯ Slide the WOLFF SLEEVE (7) over the BENCH FRAME (3). ¯ Securely assemble the BENCH FRAME (3

ملخص المحتوى في الصفحة رقم 4

PARTS LIST DESCRIPTION QTY PART # QTY KEY DESCRIPTION PART # KEY -4 "PARABODY" LOGO END CAP 14 6467001 1 REAR LEG 6706303 1 2 6590801 3 X 2" GUIDE INSERT 15 1 SWIVEL PLATE 2 6706203 1 U-PIN 16 6619301. 1 BENCH FRAM~ 6705703 3 1 3118401 4" VINYL CAP 17 2 1/4 X 2 X 16-1/2" PLATE 4 6681902 6 3/8 X 1¯ BOLT 18 3102909 1 6624202 LEFT BACK PAD ANGLE 5 2 3102904 3/8 X 3¯ BOLT 1 19 RIGHT BACK PAD ANGLE 6 6624302 2 1/2 X 1-1/4" BOLT 20 3202101 1 WOLFF SLEEVE 6623702 7 2 1/2 X 3¯ BOLT 21 3102910 1 8 623650

ملخص المحتوى في الصفحة رقم 5

,N/I-I X rdI ~.. ,N/T-I X ~/I ¢ X’IflDIzl

ملخص المحتوى في الصفحة رقم 6

* All connections use one 3/8 X 1" BOLT (18) and one 3/8" FLAT WASHER (23) FIGURE 6 STEP 6: ¯ Securely fasten the BACK PAD (9) to the LEFT (5) and RIGHT (6) BACK PAD ANGLES using four 3/8 BOLTS (18) and four 3/8" FLAT WASHERS (23) as shown in FIGURE ¯ Securely fasten the SEAT PAD (10) to the HINGE TABS (13) using two 3/8 1"BOL TS (18) and two 3/8" FLAT WASHERS (23) as shown in FIGURE ¯ Securely tighten the four connections on the 1/4 X 2 X 16-1/2" PLATES (4), then back nuts off 1/4 of a turn