ParaBody 781 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

781 SWIVEL CABLE KIT
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H 1 1
Version: 781101
PART # 7123201
Revision: 05/23/01
REV . A

ملخص المحتوى في الصفحة رقم 2

PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 7118508 GUIDE BRACKET 1 3 3102514 3/8” SAE WASHER 4 2 7122101 CABLE 2 4 3102955 3/8 X 4-1/4” BOLT 2 WEIGHT STACK PULLEY CABLE BRACKET 3/8” LOCK NUT 3/8 X 1-3/4” BOLT PULLEY ARM CABLE FIGURE 1 STEP 1: • Remove PULLEY and PULLEY BRACKET from the 777 GYM SYSTEM. Discard the PULLEY BRACKET. See FIGURE 1. 2

ملخص المحتوى في الصفحة رقم 3

FIGURE 2 3/8 X 3-3/4” BOLT 3/8” LOCK NUT 3/8 X 3-3/4” BOLT 3/8” LOCK NUT STEP 2: • Remove one 3/8” LOCK NUT and one 3/8 X 3-3/4” BOLT from the TOP and BOTTOM PLATES as shown in FIGURE 2. Discard the 3/8 X 3-3/4” BOLTS. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 3

ملخص المحتوى في الصفحة رقم 4

FIGURE 3 3 3/8 X 4-1/4” 4 2 3/8” LOCK NUT SHORT CABLE STEP 3: • Assemble the CABLES (2) to the TOP PLATES using one 3/8 X 4-1/4” BOLT (4), two 3/8” SAE WASHERS (3) and one previ- ously removed 3/8” LOCK NUT as shown in STEP 3. • Disassemble the SHORT CABLE and the turnbuckle on LONG CABLE (2) as shown in FIGURE 3. The SHORT CABLE will be reassembled later. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 4

ملخص المحتوى في الصفحة رقم 5

1 2 SHORT CABLE FIGURE 4 STEP 4: • CAREFULLY slide the GUIDE BRACKET (1) through the CABLES (2) as shown in FIGURE 4. • Assemble the SHORT CABLE and the turnbuckle to each CABLE (2) as shown in FIGURE 4. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 5

ملخص المحتوى في الصفحة رقم 6

WEIGHT 2 STACK CABLE 3/8” LOCK NUT 3/8 X 1-3/4” BOLT PULLEY ARM CABLE FIGURE 5 STEP 5: • Slide the GUIDE BRACKET (1) up and reattach the WEIGHT STACK CABLE as shown in FIGURE 5. • Loop the ARM CABLE around the previously removed pulley and assemble it to the GUIDE BRACKET (1) with the previously removed hardware as shown in FIGURE 5. 6

ملخص المحتوى في الصفحة رقم 7

FIGURE 6 2 3/8 X 4-1/4” 4 3 3/8” LOCK NUT STEP 6: • Assemble the CABLES (2) to the BOTTOM PLATES using one 3/8 X 4-1/4” BOLT (4), two 3/8” SAE WASHERS (3) and one previously removed 3/8” LOCK NUT as shown in STEP 6. 7

ملخص المحتوى في الصفحة رقم 8

2 TURN- BUCKLE JAM NUT FIGURE 7 STEP 7: • Adjust the turnbuckle on each CABLE (2) to add tension to the CABLES (2). Secure turnbuckle with the JAM NUTS as shown in FIGURE 7. • Refer to the 777 USER GUIDE to adjust tension in the systems cables and tighten all jam nuts securely. 8