Life Fitness Arctic Silver 90S دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

93S, 90S Stairclimbers
Assembly Instructions

ملخص المحتوى في الصفحة رقم 2

Congratulations... and welcome to the world of The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of the Stairclimber as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Stairclimber.

ملخص المحتوى في الصفحة رقم 3

IMPORTANT SAFETY INSTRUCTIONS! ⇒ DO NOT locate the Stairclimber outdoors, near swimming pools, or in areas of high humidity. ⇒ DO NOT operate your Stairclimber if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services at the number in the Operation Manual. ⇒ DO NOT locate the Stairclimber any closer than 30 inches ( 76 cm ) to a television set. ⇒ DO NOT locate additional Stairclimbers any closer than a minimum of 42 inche

ملخص المحتوى في الصفحة رقم 4

TOOLS REQUIRED FOR ASSEMBLY... Phillips Screwdriver, T27 Torx Screwdriver, Socket Set PARTS DESCRIPTION 1 Hex Head Bolt Qty: 2 2 Lock Nut Qty: 2 3/8 – 16 x 3 3/8 – 16 3 Hex Head Bolt Qty: 2 4 Torx Cap Screw (Model 93S) Qty: 4 5/16 – 18 x 1.500 1/4 – 20 x .625 (Model 90S) Qty: 10 5 Phillips Pan Head Screw (Model 93S) Qty: 8 6 Flat Head Screw (Model 93S) Qty: 6 #8 – 18 x .625 (Model 90S) Qty: 4 1/4 – 20 x .625 7 Phillips Pan Head Screw Qty: 4 8 Phillips Cap Screw Qty: 2 #8 – 18 x .75 #6 – 32 x .3

ملخص المحتوى في الصفحة رقم 5

1. Before proceeding, familiarize yourself with the parts of the B Stairclimber and make sure that you have received all the items C described in the Parts List. 20 2. Locate the MONOCOLUMN (#10). Position the MONOCOLUMN SHROUD (#20) onto the MONOCOLUMN as shown. Position 10 the MONOCOLUMN near the MONOCOLUMN MOUNTING BRACKET (B) as shown. Detach and feed the CONSOLE WIRE HARNESS (C) through the MONOCOLUMN and out through the D DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. Pivot the MONOCOLU

ملخص المحتوى في الصفحة رقم 6

4. (Model 93S / 90S International) Locate the TELEMETRY D 3P CABLE (#17). Feed the 3-PIN CONNECTOR (3P) end of the cable through the front of the HANDLEBAR ASSEMBLY (#15). 15 The cable must be routed down the HANDLEBAR BRACKET TUBE (F) and back up the top of the MONOCOLUMN (#10). Feed the 3-PIN CONNECTOR through the DISPLAY CONSOLE 10 MOUNTING BRACKET (D) ACCESS HOLE. 5. (Model 93S) Align the USER LEFT BULLHORN (#13) to the HANDLEBAR BRACKET TUBE (F). Using three MOUNTING SCREWS (#6), secure th

ملخص المحتوى في الصفحة رقم 7

7. Locate one of the VERTICAL HANDRAILS (#12). Carefully insert the top of the VERTICAL HANDRAIL into the user right end of the HANDLEBAR ASSEMBLY (#15). Align the mounting holes. Secure the VERTICAL HANDRAIL to the HANDLEBAR 15 ASSEMBLY using two MOUNTING SCREWS (#4). Position the bottom of the VERTICAL HANDRAIL over the mounting hole in 4 the top of the right FRAME LEG (K). Using one HEX HEAD BOLT (#3), mount the VERTICAL HANDRAIL to the right FRAME LEG as shown. Tighten the BOLT securely. Rep

ملخص المحتوى في الصفحة رقم 8

PRE-OPERATION CHECKLIST Ensure that all fasteners are tight. Make sure the Stairclimber is properly leveled and stable. (Refer to the Operation Manual) Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual) Read the entire Operation manual before using the Stairclimber. LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE Vérifiez si tous les dispositifs de fixation sont serrés Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable. (Référez-vous a