Life Fitness Lat Pulldown دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Lat Pulldown
Assembly Instructions

ملخص المحتوى في الصفحة رقم 2

Lat Pulldown Assembly Instructions Item Qty Description Part Number Item Qty Description Part Number 1 1 Front Brace 79818XX 24 1 Rear Shroud 8024806 2 1 Rear Brace 80120XX 25 1 Front Shroud 8024706 3 1 Tower 79854XX 26 4 M10 x 20mm Bolt 3251701 4 4 M10 x 130mm Bolt 3251720 27 3 Plate 7322301 5 44 3/8” Flat Washer 3102514 28 1 Cam Guard 8013201 6 15 M10 Nylock Nut 3242002 29 2 M5 x 10mm Phillips Screw 3239101 7 1 Seat Frame 80118XX 30 2 Shaft Collar 7357901 8 6 M10 x 90mm Bolt 3251715 31 2 Rolle

ملخص المحتوى في الصفحة رقم 3

ملخص المحتوى في الصفحة رقم 4

Lat Pulldown Assembly Instructions 1. LOOSELY assemble the FRONT BRACE (1) and REAR BRACE (2) to the TOWER (3) using four M10 X 130mm BOLTS (4), eight 3/8" SAE WASH- ERS (5) and four M10 NYLOCK NUTS (6) as shown. 2. LOOSELY assemble the SEAT FRAME (7) to the FRONT BRACE (1) and REAR BRACE (2) using four M10 X 90mm BOLTS (8), eight 3/8" SAE WASHERS (5) and four M10 NYLOCK NUTS (6) as shown. 3. LOOSELY assemble the TOP BRACE (9) to the SEAT FRAME (7) and TOWER (3) using two M10 X 90mm BOLTS (8), f

ملخص المحتوى في الصفحة رقم 5

8. Assemble the OUTPUT CAM (20), OUTPUT PLATE (21), and OUTPUT RING (22) using three M10 X 45mm BOLTS (23) and three 3/8" SAE WASHERS (5) as shown. Tighten the BOLTS securely. 9. Assemble the REAR SHROUD (24) and FRONT SHROUD (25) to the TOWER (3) using four M10 X 20mm BOLTS (26), four 3/8" SAE WASH- ERS (5) as shown. Be sure all tabs along the sides and top of the SHROUDS are fully engaged in the slots located inside the TOWER. Tighten the BOLTS securely. Do not overtighten the BOLTS. 10. Secur

ملخص المحتوى في الصفحة رقم 6

Lat Pulldown Assembly Instructions 12. Slide one SHAFT COLLAR (30) over each shaft of the ROLLER PAD BRACKET (11). 13. Attach the ROLLER PADS (31) to the ROLLER PAD BRACKET (11) using two M10 X 35mm BOLTS (19) and two PLATES (27) as shown. Tighten the BOLT securely. 14. Slide the SHAFT COLLARS (30) to meet the ROLLER PADS (31) and secure the ROLLER PADS against the PLATES (27) by tightening the SHAFT COLLAR set screws. Install the two ROLLER PAD CAPS (32). 15. Attach the SEAT PAD (33) to the SEA

ملخص المحتوى في الصفحة رقم 7

NOTE: Some components have been removed from the illustration for clarity. 17. Assemble one M10 HEX JAM NUT (35) onto one end of the CABLE (36) approximately 1/2”. Assemble the ROD END BEARING (37) to the same end of the CABLE until it meets the M10 HEX JAM NUT. Tighten the M10 HEX JAM NUT securely. 18. Loosely assemble the ROD END BEARING (37) of the CABLE (36) to the WORKARM (18) using one M10 X 40mm BOLT (38), SPACER (39), 3/8" SAE WASHER (5) and M10 NYLOCK NUT (6) . 19. Route the CABLE (36)

ملخص المحتوى في الصفحة رقم 8

Lat Pulldown Assembly Instructions © 2006 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness is a registered trademark of Brunswick Corporation. TCPD 7.28.06 8060701 RevA-3