ملخص المحتوى في الصفحة رقم 1
HEAVY DUTY COMBO RACK (HDCR)
WARNING:
Read and follow all directions for each step to insure proper assembly of this product.
CLASS SB (Studio): Professional and / or commercial use (Commercial Use Only)
PART #7946901 D-4
DATE: 2/08
ملخص المحتوى في الصفحة رقم 2
HAMMER STRENGTH HEAVY DUTY RACKS SAFETY & WARRANTY Purchasers of Hammer Strength products should read the Owner's Manual and all of the warning labels on the products before using them. Because these products may be used in commercial settings, it is the purchaser's responsibility to instruct all individuals, whether users, trainers or observers, on the proper usage of the equipment. Contact Hammer Strength if you do not know how to use this equipment. Hammer Strength recommends that all commer
ملخص المحتوى في الصفحة رقم 3
WARNING SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. YOU MUST FOLLOW THESE PRECAUTIONS TO AVOID INJURY! 1. Before using, read all the warnings and obtain instruction on the use of this machine. Use only for intended exercise. DO NOT modify the equipment. 2. Obtain a medical exam before beginning any exercise program. 3. Keep body and clothing free of all moving objects. 4. Inspect equipment daily. Tighten all loose connections, and replace worn parts immediately. DO NOT use if it appears damaged.
ملخص المحتوى في الصفحة رقم 4
LIMITED WARRANTY WHAT IS COVERED This Hammer Strength commercial exercise equipment (Signature Benches and Racks) is warranted to be free of all defects in material and workmanship to the original purchaser for the specific items and duration listed: 10 years on structural frame 1 year on grips 1 year for rust or corrosion of structural frame. Scratches or scrapes where the subsurface of the unit has been exposed must have been properly repaired by the customer. 90 days on upholstery and a
ملخص المحتوى في الصفحة رقم 5
LIMITED WARRANTY HOW TO GET PARTS & SERVICE Simply call Customer Support Services at (800) 351-3737, Monday through Friday from 8:00 a.m. to 6:00 p.m. Central Standard Time, and tell them your name, address and the serial number of your Product. They will tell you how to get a replacement part, or, if necessary, arrange for service where your Product is located or advise you on how and where to ship the Product for service. Before shipping: 1. Obtain a Return Authorization Number (RA#) from Cu
ملخص المحتوى في الصفحة رقم 6
1. Frame Construction: Frame is constructed of mechanical quality steel purchased in mill run quantities. Frame is pri- marily 3" x 3" square shaped tubing and 3” x 2” shaped tubing with 7 gauge and 11 gauge wall thickness. 2. Frame Finish: The frames are coated with an electrostatic epoxy powder coat finish. 3. Bolts: Most hardware is English and has a corrosion resistant finish. Grade 5 or greater in strength. 4. Equipment Anchoring: All machines have holes in the feet, these allow easy anchor
ملخص المحتوى في الصفحة رقم 7
COMPONENTS LIST * ITEM NO. QTY. PART NO. DESCRIPTION 1 2 HDCR8-CFUPR-0 FRONT RIGHT UPRIGHT 2 2 HDCR8-CFUPL-0 FRONT LEFT UPRIGHT 3 2 HDCR8-LSF-0 BASE 4 56 HHB.5X4.5 1/2 X 4-1/2” BOLT 5 70 H-BACK-WASH BACKING DOME WASHER 6 66 WASH.5STAR 1/2” INTERNAL LOCK WASHER 7 58 NUT.5LOCK 1/2” LOCK NUT 8 2 HDCR8-USF-1 CROSS SUPPORT 9 2 HDCR8-CPU-0 PULL-UP SUPPORT 10 1 HDCR8-RX-0 LOWER CROSS BRACE 11 4 HDCR8-RUP-0 REAR UPRIGHTS 12 20 ANG-WT-HORN-ASSY WEIGHT HORN 13 20 HHB.375X4.5 3/8 X 4-1/2” BOLT 14 40 WASH.3
ملخص المحتوى في الصفحة رقم 8
HARDWARE: 17 ½ X 3-1/2” Bolt 4 ½ X 4-1/2” Bolt 13 3/8 X 4-1/2” Bolt 6 14 5 ½” Internal Lock Washer 3/8” Flat Washer 7 15 Backing Backing Dome Dome W Washer asher 3/8” Lock Nut ½” Lock Nut 8
ملخص المحتوى في الصفحة رقم 9
STEP 1: Loosely assemble the two FRONT RIGHT UPRIGHTS (1) and the two FRONT LEFT UPRIGHTS (2) to the two BASES (3) using eight 1/2 x 4-1/2” BOLTS (4), eight BACKING DOME WASHERS (5), eight 1/2” INT LOCK WASH- ERS (6) and eight 1/2” LOCK NUTS (7). NOTE: Make sure the FRONT RIGHT & LEFT UPRIGHTS (1 & 2) face each other with the slot openings facing outward. 9
ملخص المحتوى في الصفحة رقم 10
9 8 6 4 9 7 6 8 9 7 1 6 1 2 2 A 6 2 B 10 4 5 3 6 7 7 6 5 4 STEP 2: LOOSELY assemble the two CROSS SUPPORTS (8) and two PULL-UP SUPPORTS (9) to the top of the FRONT RIGHT & LEFT UPRIGHTS (1 & 2) using eight 1/2 X 4-1/2” BOLTS (4), sixteen 1/2” INT TOOTH LOCK WASHERS (6) and eight 1/2” LOCK NUTS (7). Assemble the LOWER CROSS BRACE (10) to the inside of the two BASES (3) using four 1/2 X 4-1/2” BOLTS (4), four BACKING DOME WASHERS (5), four 1/2” INT TOOTH LOCK WASHERS (6) and four 1/2” LOCK NUTS
ملخص المحتوى في الصفحة رقم 11
7 6 5 4 7 6 1 2 11 11 7 6 3 3 5 4 5 4 STEP 3: Assemble the bottom of the four REAR UPRIGHTS (11) to the bottom of the BASES (3) using eight 1/2 X 4-1/2” BOLTS (4), eight BACKING DOME WASHERS (5), eight 1/2” INT TOOTH LOCK WASHERS (6) and eight 1/2” LOCK NUTS (7). Assemble the top of the four REAR UPRIGHTS (11) to the FRONT RIGHT & LEFT UPRIGHTS (1 & 2) using eight 1/2 X 4-1/2” BOLTS (4), eight BACKING DOME WASHERS (5), eight 1/2” INT TOOTH LOCK WASHERS (6) and eight 1/2” LOCK NUTS (7). 11
ملخص المحتوى في الصفحة رقم 12
7 6 5 4 4 5 14 6 12 7 5 5 13 13 14 11 5 14 12 14 15 STEP 4: SECURELY assemble the bottom of the ten WEIGHT HORNS (12) to the REAR UPRIGHTS (11) using twenty 3/8 x 4-1/2” BOLTS (13), twenty BACKING DOME WASHERS (5), forty 3/8” FLAT WASHERS (14), and twenty 3/8” LOCK NUTS (15). SECURELY assemble the top of the WEIGHT HORNS (12) to the REAR UPRIGHTS (11) using twenty 1/2 X 4-1/2” BOLTS (4), twenty BACKING DOME WASHERS (5), twenty 1/2” INT TOOTH LOCK WASHERS (6), and twenty 1/2” LOCK NUTS (7). 12
ملخص المحتوى في الصفحة رقم 13
17 5 10 6 7 16 STEP 6: Assemble the the LONG BENCH LOCK (16) to the LOWER CROSS BRACE (10) using two 1/2 X 3-1/2” BOLTS (17), two BACKING DOME WASHERS (5), two 1/2” INT LOCK WASHERS (6), and two 1/2” LOCK NUTS (7). 13
ملخص المحتوى في الصفحة رقم 14
STEP 7: Insert the two LEFT BAR CATCHES (18) and the two LEFT BAR SUPPORTS (19) into the desired slots of the two FRONT LEFT UPRIGHTS (2). Insert the two RIGHT BAR CATCHES (20) and the two RIGHT BAR SUPPORTS (21) into the desired slots of the two FRONT RIGHT UPRIGHTS (1). Securely tighten all loose assemblies. 14
ملخص المحتوى في الصفحة رقم 15
C C E D I F F 1 H G 2 STEP 8: Spotter Platform accessories are available for the HDCR8. Assemble each Spotter Platform (C) to the FRONT RIGHT & LEFT UPRIGHTS (1 & 2) using two BOLTS (D), two DOME WASHERS (E), two SPACERS (F), one WEAR PLATE (G), two FLAT WASHERS (H), and two NUTS (I) as shown in the illustration. NOTE: All necessary hardware for the Spotter Platform assembly is included with the accessory. Make sure the flange on the SPACER (F) faces the inside of the rack. 15
ملخص المحتوى في الصفحة رقم 16
Preventative Maintenance Tips Action Daily WeeklyQuarterly Bi-AnnuallyAs Needed Clean Hand Grips X Inspect Visual Overall X Hardware X Frame X Hand Grips X Clean: • Hand grips with mild soap and water. • Frame damage can be repaired with touch-up paint can be purchased from your Hammer Strength customer service representative. Inspect: • Hardware should be checked for looseness. Tighten as required. • Frames should be inspected for wear or damage. • Hand Grips should be checked for wear or
