ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
PLATINUM MARCY
Safety Notice
HOME GYM
Hardware Identifier
PM-3200
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
PM-3200
Retain This
Manual for
Reference
110525
OWNER'S
®
MANUAL
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE PACK……….....….....................................................................……….. 4 ASSEMBLY INSTRUCTIONS.........................................................................……….. 7 PARTS LIST………………………………………………………………………………….. 23 RESISTAN
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a t
ملخص المحتوى في الصفحة رقم 4
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
ملخص المحتوى في الصفحة رقم 5
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
ملخص المحتوى في الصفحة رقم 6
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
ملخص المحتوى في الصفحة رقم 7
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Push two Ø 2 3/8” x 1” Rubber Bumpers (#43) onto the Guide Rods (#13) from the bottom. Insert the Guide Rods into the holes on the Rear Base Frame (#2). The Guide Rods have holes on the rods about 2/3 way d
ملخص المحتوى في الصفحة رقم 9
DIAGRAM 1 8
ملخص المحتوى في الصفحة رقم 10
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Slide the 14 Weight Plates (#34) onto the Guide Rods (#13). Make sure the deep grooves on the Plates are all facing down and toward back of the machine. If the locking holes on the guide rods are more than 2-3 inches from the upper most, then you have installed the Guide Rods upside down. Align the holes of the Weight Plates. Insert the Selector Rod (#14) through the center hole. Slide the ring on
ملخص المحتوى في الصفحة رقم 11
DIAGRAM 2 10
ملخص المحتوى في الصفحة رقم 12
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#6) to the Upper Frame (#4). Secure it with one 6 1/8” Front Press Axle (#37), one Ø ¾” Washer (#84), one Ø ¾” Lock Washer (#88), one M10 x 1” Allen Bolt (#73), and one Ø 2” End Cap (#47) on each end of the Axle. B.) Insert the axle on the Right Butterfly Base (#7) into the Front Press Base from bottom. Slide a Lock Ring (#52) onto the Axle. Align the holes. Secure it with one M6 x 1 ¾” Allen Bolt (#77) and M6 Aircraft Nut (#89).
ملخص المحتوى في الصفحة رقم 13
DIAGRAM 3 12
ملخص المحتوى في الصفحة رقم 14
STEP 4 (See Diagram 4) A.) Attach the Main Seat Support (#1) to the Front Vertical Frame (#3). Secure it with two M10 x 3 ¾” Carriage Bolts (#79), one 4 ¾” x 1 ¾” Bracket (#22), two ¾” Washers (#84), and two M10 Aircraft Nuts (#83). B.) Attach the Seat Bracket (#20) onto the Main Seat Support. Place the Seat Pad (#38) onto Main Seat Support and Seat Bracket. Secure it with two M8 x 3” Allen Bolts (#74), two M8 x 5/8” Allen Bolts (#76), and four Ø 5/8” Washers (#86). C.) Attach the L
ملخص المحتوى في الصفحة رقم 15
CABLE LOOP DIAGRAM 14
ملخص المحتوى في الصفحة رقم 16
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 118” Upper Cable (#59) to the opening on the front of the Upper Frame (#4). Note: The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69), two Ø 7/8” x 5/8” Pulley Bushings (#44), and one M10 Aircraft Nut (#83). C.) Draw the Cable over the Pulley towards the back of the machine to the second opening on the Upper Frame. Repeat step
ملخص المحتوى في الصفحة رقم 17
DIAGRAM 5 16
ملخص المحتوى في الصفحة رقم 18
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 110” Butterfly Cable (#61) onto the hook on the Right Butterfly Base (#7). B.) Draw the Cable to the right Swivel Pulley Bracket (#26). C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø ¾” Washers (#84), and one M10 Aircraft Nut (#83). D.) Draw the Cable around the Pulley then downward. Attach the Cable to an Angled Floating Pulley Bracket (#25). Repeat C to install anothe
ملخص المحتوى في الصفحة رقم 19
DIAGRAM 6 18
ملخص المحتوى في الصفحة رقم 20
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 157” Lower Cable (#60) to the opening on the bottom of the Leg Developer (#11). B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69), two Ø 7/8” x Ø 5/8” Bushings (#44), and one M10 Aircraft Nut (#83). C.) Draw the Cable underneath the Pulley to the open bracket on Base Frame (#5). D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø ¾” Washers (#84),
