ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE BENCH
Hardware Pack
PHC-700
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PHC 700
Retain This
Manual for
Reference
07-19-03
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICE....................................................................... 2 HARDWARE PACK…….......…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM......................................................
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
ملخص المحتوى في الصفحة رقم 4
HARDWARE PACK 3
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Right and Left Upright Beams (#1 & 2) by a Cross Brace (#3) in the mid- span. Align the holes and secure each end with one Bracket (#17), two M10 x 2 ¾” Carriage Bolts (#37), two ∅ ¾” Washers (#45), and two M10 Aircraft Nuts (#43). B.)
ملخص المحتوى في الصفحة رقم 6
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#6) to the Cross Brace (#3). Secure it with a Bracket (#17), two M10 x 2 ¾” Carriage Bolts (#37), two ∅ ¾” Washers (#45), and two M10 Aircraft Nuts (#43). B.) Attach the Front Support (#8) to the Main Seat Support (#6). Secure it with three M10 x 2 ¾” Carriage Bolts (#37), ∅ ¾” Washers (#45), and M10 Aircraft Nuts (#43). DIAGRAM 2 5
ملخص المحتوى في الصفحة رقم 7
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#10) to the open bracket on the Front Support (#8). Secure it with an Axle (#44), two ∅ ¾” Washers (#45), and two M10 x ¾” Allen Bolts (#39). B.) Insert one Foam Tube (#16) halfway through the hole on the Front Support (#8). Insert two Foam Tubes halfway through the holes on the Leg Developer. Push six Foam Rolls (#23) onto the Foam Tubes. Plug six Foam Roll End Caps (#56) into the ends. C.) Attach the Curl Handle (#11) to the
ملخص المحتوى في الصفحة رقم 8
STEP 4 (See Diagram 4) A.) Attach the hole-side of the Backrest Supports (#7) to both ends of the pivot on the Main Seat Support (#6). Secure it with one M12 x 7 ¼” Hex Bolt (#38) and M12 Aircraft Nut (#42). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar. B.) Place the Backrest Board (#19) onto the Backrest Supports (#7). Secure it with four M6 x 1 3/8” Hex Bolts (#41) and ∅ ½” Washers (#47). C.) Place the Seat (#18) onto the Main Seat Support (#
ملخص المحتوى في الصفحة رقم 9
STEP 5 (See Diagram 5) A.) Insert a M12 x 6 ¼” Hex Bolt (#54) through the Right Butterfly (#12). Secure the Bolt with a M12 Regular Nut (#53). Insert the Bolt through the hole on the Right Upright Beam (#1) and secure it with a M12 Lock Knob (#49). B.) Attach the Butterfly Handle (#14) to the Right Butterfly (#12). Secure it with one M10 x ¾” Allen Bolt (#39) and ∅1 ¼” Washer (#55). C.) Attach Spring Clip (#48) to weight post on the Butterfly. D.) Repeat the Procedures A, B & C a
ملخص المحتوى في الصفحة رقم 10
9
ملخص المحتوى في الصفحة رقم 11
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Upright Beam 1 2 Left Upright Beam 1 3 Cross Brace 1 4 Crutch 2 5 Backrest Adjustment Bar 1 6 Main Seat Support 1 7 Backrest Support 2 8 Front Support 1 9 Arm Curl Stand 1 10 Leg Developer 1 11 Curl Handle 1 12 Right Butterfly 1 13 Left Butterfly 1 14 Butterfly Handle 2 15 Curl Handle Tube 1 16 Foam Tube 3 17 Bracket 3 18 Seat 1 19 Backrest Board 1 20 Arm Curl Pad 1 21 Curl Handle Grip 2 22 L-shape Pin 1 23 Foam Ro
ملخص المحتوى في الصفحة رقم 12
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cust
