ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
MARCY HOME GYM
Safety Notice
Hardware Identifier
MWM 800
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 800
Retain This
Manual for
Reference
08-20-02
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
OWNER'S
www.impex-fitness.com
MA
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES...................................................................……….. 2 HARDWARE IDENTIFIER.....….....................................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 8 EXPLODED DIAGRAM......................................
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time sho
ملخص المحتوى في الصفحة رقم 4
Hardware Identifier 3
ملخص المحتوى في الصفحة رقم 5
4
ملخص المحتوى في الصفحة رقم 6
5
ملخص المحتوى في الصفحة رقم 7
6
ملخص المحتوى في الصفحة رقم 8
7
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY INSTRUCTION Tools Required to Assemble the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Flat Head Screwdriver NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Main Base Frame (#2) and Front Base (#3) to the Front Stabilizer (#5). Align the holes then secure them with two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74). B.) Att
ملخص المحتوى في الصفحة رقم 10
DIAGRAM 1 9
ملخص المحتوى في الصفحة رقم 11
STEP 2 (See Diagram 2) A.) Attach the Seat Support (#15) to the Vertical Beam (#4). Secure it with one Bracket (#26), two 3/8” x 3 7/8” Carriage Bolts (#68), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74). B.) Attach the Seat post (#14) to the Seat Support (#15). Secure it with one Bracket (#26), two 3/8” x 3” Carriage Bolts (#69), ∅ 3/8” Washers (#77), and 3/8” Aircraft Nuts (#74). C.) Secure the bottom of the Seat Post (#14) to the Front Base (#3) with one 3/8” x 4 ½” Carriag
ملخص المحتوى في الصفحة رقم 12
DIAGRAM 2 11
ملخص المحتوى في الصفحة رقم 13
STEP 3 (See Diagram 3) A.) Attach the Front Press Lock Pin (#22) to the Vertical Beam (#4). Secure it with one M8 x 2 ½” Allen Bolt (#64), two ∅ ¼” Washers (#76), and one M8 Aircraft Nut (#73). Plug a 1 ½” Square End Cap (#35) to the front opening on the Vertical Beam. B.) Plug two ½” Metal Bushings (#72) onto the side-holes on the Upper Frame (#6). Attach the Front Press Base (#9) to the Bushings. Secure it with one ½” x 6 1/8” Allen Bolt (#56), two ∅ ½” Washers (#78), and one ½” Ai
ملخص المحتوى في الصفحة رقم 14
STEP 4 (See Diagram 4) A.) Plug two ½” Metal Bushings (#72) to the pivot on the Left Butterfly (#12). Attach the Left Butterfly to the Front Press Base (#9). Secure it with one ½” x 3 1/8” Allen Bolt (#58), two ∅ ½” Washers (#78), and one ½” Aircraft Nut (#75). B.) Slide two Foam Grips (#42) onto the Left Butterfly handle. C.) Repeat Procedures A & B above to install the Right Butterfly (#11). DIAGRAM 4 13
ملخص المحتوى في الصفحة رقم 15
CABLE LOOP DIAGRAM 14
ملخص المحتوى في الصفحة رقم 16
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 137” Upper Cable (#52) to the open bracket on the front of the Upper Frame (#6). Note: The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#28) to the bracket and secure it with one 3/8” x 1 ¾” Allen Bolt (#61), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74). C.) Draw the Cable to the open slot on the Vertical Beam (#4). Install a Pulley to the opening. Align the holes and secure it with
ملخص المحتوى في الصفحة رقم 17
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 47” Butterfly Cable (#54) to the left Butterfly Bracket (#10). Secure the Cable to the Bracket with one 3/8” x 1 3/16” Allen Bolt (#62), ∅ 3/8” Washer (#77), and 3/8” Aircraft Nut (#74). B.) Attach a Swivel Pulley Bracket to the Pivot on the Vertical Beam (#4). Secure it with one 3/8” x 2 5/8” Allen Bolt (#60), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74). Draw the Cable to the Swivel Pulley Bracket. C.
ملخص المحتوى في الصفحة رقم 18
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 133” Lower Cable (#53) to the opening on the Leg Developer (#17). Attach a Pulley (#28) to the opening. Secure it with one 3/8” x 2 5/8” Allen Bolt (#60), two ∅ ½” Bushings (#71), two ∅ 3/8” Washers (#77), and one 3/8” Aircraft Nut (#74). B.) Draw the Cable underneath the Pulley to the open slot on the Vertical Beam (#4). Install another Pulley as described in Step A. C.) Draw the Cable underneath the Pulley then upward to the
ملخص المحتوى في الصفحة رقم 19
DIAGRAM 7 18
ملخص المحتوى في الصفحة رقم 20
19
