ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY OLYMPIC BENCH
Hardware Pack
Assembly Instruction MWB 716
Parts List
Warranty
Ordering Parts
Model
MWB 716
Retain This
Manual for
Reference
08-18-03
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitne
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE PACK……….....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........................................................................... 4 EXPLODED DIAGRAM……………………………………………………………... 8 PARTS LIST………………………………………
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
ملخص المحتوى في الصفحة رقم 4
HARDWARE PACK 3
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the mid-span. Align the holes and secure them with one Weight Post (#3), three M10 x 3 1/8” Carriage Bolts (#36), three ∅ ¾” Washers (#43), and three M10 Aircraft Nuts (#46) on each
ملخص المحتوى في الصفحة رقم 6
STEP 2 (See Diagram 2) A.) Attach the Front Stabilizer (#6) to the Main Seat Support (#5). Secure it with three M10 x 2 ¾” Carriage Bolts (#37), ؾ” Washers (#43), and M10 Aircraft Nuts (#46). B.) Attach the Main Seat Support (#5) to the Cross Brace. Secure it with one Bracket (#7), two M10 x 3 1/8” Carriage Bolts (#36), two Ø ¾” Washers (#43), and two M10 Aircraft Nuts (#46). DIAGRAM 2 5
ملخص المحتوى في الصفحة رقم 7
STEP 3 (See Diagram 3) A.) Attach the side-holes on the Backrest Supports (#8) to the long pivot on the Main Seat Support. Place the Backrest Board (#11) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Hex Bolts (#41) and Ø ½” Washers (#45). Place the other end of Backrest Board rest against the backrest Adjustment Bar. B.) Attach the Seat Bracket (#9) to the short pivot on Main Seat Support. Secure it with one M10 x 4 ¾” Allen Bolt (#38), two Ø ¾” Washers (#43), and one
ملخص المحتوى في الصفحة رقم 8
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#15) to the Front Stabilizer (#6). Secure it with one Axle (#19), two M10 x 5/8” Allen Bolts (#39), and two Ø ¾” Washers (#43). B.) Insert one Foam Tube (#18) halfway through the hole on the Front Stabilizer. Insert two Foam Tubes halfway through the holes on the Leg Developer. C.) Push six Foam Rolls (#22) onto the Foam Tubes from both ends. Plug six Foam Roll End Caps (#29) into the ends. D.) Attach the Curl Bar (#16) to the brac
ملخص المحتوى في الصفحة رقم 9
8
ملخص المحتوى في الصفحة رقم 10
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Rear Upright Beam 2 2 Cross Brace 1 3 Weight Post 2 4 Crutch 2 5 Main Seat Support 1 6 Front Stabilizer 1 7 Bracket 1 8 Backrest Support 2 9 Seat Bracket 1 10 Arm Curl Stand 1 11 Backrest Board 1 12 Seat 1 13 Arm Curl Pad 1 14 Backrest Adjustment Bar 1 15 Leg Developer 1 16 Curl Bar 1 17 Curl Bar Handle 1 18 Foam Tube 3 19 Axle 1 20 Lock Knob 3 21 Spring Clip 3 22 Foam Roll 6 23 Curl bar Handle Grip 2 24 ∅ 1 1/8” Cone-sha
ملخص المحتوى في الصفحة رقم 11
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cus
