ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
MARCY WEIGHT BENCH
Hardware Identifier
MWB -558
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MWB 558
Retain This
Manual for
Reference
09-12-03
IMPEX FITNESS PRODUCTS
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICE.....................................................................……….. 2 HARDWARE PACK…….......…......….............................................................……….. 3 ASSEMBLY INSTRUCTIONS.........................................................................……….. 4 EXPLODED DIAGRAM……….....................................
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one per
ملخص المحتوى في الصفحة رقم 4
HARDWARE PACK 3
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach two Ø 2 3/8” End Caps (#20) to the bottom of two Upright Beams (#1 & #2). B.) Connect the Left & Right Upright Beams (#1) & (#2) by the Cross Brace (#3) in the mid-span. Align the holes then secure each end of Cross Brace with one Bent Br
ملخص المحتوى في الصفحة رقم 6
STEP 2 (See Diagram 2) A.) Attach a Ø 2 3/8” End Cap (#20) to the bottom of the Leg Developer Holder (#8). B.) Attach the Leg Developer Holder to the front of the Main Seat Support (#6). Secure it with three M8 x 5/8” Allen Bolts (#38) and Ø 5/8” Washers (#33). C.) Attach the top of Diagonal Support (#7) to the Main Seat Support (#6). Secure it with one M8 x 2 1/8” Allen Bolt (#32), two Ø 5/8” Washers (#33) and one M8 Aircraft Nut (#34). Attach the bottom of the Diagonal Support to
ملخص المحتوى في الصفحة رقم 7
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#9) to the Leg Developer Holder (#8). Secure it with one M8 x 3 1/8” Allen Bolt (#37), two ∅ 5/8” Washers (#33), and one M8 Aircraft Nut (#34). B.) Insert one Foam Tube (#10) halfway through the hole on the Leg Developer Holder and two Foam Tubes halfway through the two holes on the Leg Developer (#9). C.) Push six Foam Rolls (#21) onto the Tubes from both ends. Attach a Spring Clip (#27) onto the weight post on the Leg Develop
ملخص المحتوى في الصفحة رقم 8
STEP 4 (See Diagram 4) A.) Attach the hole-side of the Backrest Supports (#12) to the pivot on the Main Seat Support (#6). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar (#5). Place the Backrest Board (#15) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Hex Bolts (#35) and ∅ ½” Washers (#36). B.) Place the Seat (#16) onto the Main Seat Support (#6). Secure it with four M6 x 1 3/8” Hex Bolts (#35) and Ø ½” Washers (#36). DIAGRAM
ملخص المحتوى في الصفحة رقم 9
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#17) to the Arm Curl Stand (#11). Secure it with two M8 x 5/8” Allen Bolts (#38) and Ø 5/8” Washers (#33). B.) Insert the Arm Curl Stand into the opening on top of the Leg Developer Holder. Use a M10 Lock Knob (#22) to secure the desired height. DIAGRAM 5 8
ملخص المحتوى في الصفحة رقم 10
9
ملخص المحتوى في الصفحة رقم 11
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Left Upright Beam 1 2 Right Upright Beam 1 3 Cross Brace 1 4 Bar Holder 2 5 Backrest Adjustment Bar 1 6 Main Seat Support 1 7 Diagonal Support 1 8 Leg Developer Holder 1 9 Leg Developer 1 10 Foam Tube 3 11 Arm Curl Stand 1 12 Backrest Support 2 13 Bent Bracket 2 14 Flat Bracket 1 15 Backrest Board 1 16 Seat 1 17 Arm Curl Pad 1 18 M16 Lock Knob 3 19 Ø 2 3/8” Sleeve 3 20 Ø 2 3/8” End Cap 3 21 Foam Roll 6 22 Ø 1” End Cap
ملخص المحتوى في الصفحة رقم 12
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
