ملخص المحتوى في الصفحة رقم 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
COMPETITOR BENCH
Safety Notice
CB-280
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
CB-280
Retain This
Manual for
Reference
07-1704
IMPEX FITNESS PRODUCTS
OWNER'S
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
MANUAL
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.co
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. 1 IMPORTANT SAFETY NOTICES..................................................................…. 2 HARDWARE PACK……….....…....................................................................…. 3 ASSEMBLY INSTRUCTIONS........................................................................…. 4 EXPLODED DIAGRAM………………………………………………………………. 10 PARTS LIST...................
ملخص المحتوى في الصفحة رقم 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should
ملخص المحتوى في الصفحة رقم 4
HARDWARE PACK 3
ملخص المحتوى في الصفحة رقم 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the Mid-span. Secure them with two M8 x 2 ½” Carriage Bolts (#20), one Bracket (#10), two ∅ 5/8” Washers (#26), and two M8 Aircraft Nuts (#24) on each end of the Cross Brace. B.) Insert the Backrest Adjustmen
ملخص المحتوى في الصفحة رقم 6
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with four M8 x 2 3/8” Hex Bolts (#18), one Bracket (#10), four Ø 5/8” Washers (#26), and four M8 Aircraft Nuts (#24). DO NOT tighten the Nuts and Bolts yet. B.) Attach the Front Support (#5) to the Main Seat Support (#3). Secure the first hole to the Main Seat Support with one M8 x 1 5/8” Carriage Bolt (#28), one Ø 5/8” Washer (#26), and one M8 Aircraft Nut (#24). DO NOT tighten the Nut a
ملخص المحتوى في الصفحة رقم 7
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#6) to the Front Support (#5). Secure it with one M10 x 2 3/8” Hex Bolt (#21), two Ø ¾” Washers (#31), and one M10 Aircraft Nut (#27). Do not over tighten the Bolt. Make sure the Leg Developer is able to swivel. B.) Insert two Foam Tubes (#13) halfway through the holes on the Leg Developer. Push four Foam Rolls (#12) onto the Tubes from both sides. C.) Place a Spring Clip (#39) onto the weight post on the Leg Developer. DIAGRAM 3
ملخص المحتوى في الصفحة رقم 8
STEP 4 (See Diagram 4) A.) Attach the hole-side of the Backrest Supports (#7) onto both ends of the pivot on the Main Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#11). B.) Place the Backrest Board (#8) onto the Backrest Supports. Secure it with four M6 x 1 5/8” Hex Bolts (#23) and Ø ½” Washers (#25). C.) Place the Seat Pad (#9) onto the Main Seat Support. Secure it with four M6 x 5/8” Hex Bolts (#22) and Ø ½” Washers (#25). DIAGRAM 4 7
ملخص المحتوى في الصفحة رقم 9
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#42). Secure it with two M8 x ¾” Hex Bolts (#33) and Ø 5/8” Washers (#26). B.) Insert the Arm Curl Stand into the top opening on the Front Support and secure it with a Lock Knob (#32). DIAGRAM 5 8
ملخص المحتوى في الصفحة رقم 10
STEP 6 (See Diagram 6) A.) Slide the 25lb (#36), 15lb (#37), and 10lb (#38) Weight Plates onto the Weight Bar (#35). Note: Plates must be installed in pairs, one on each side. B.) Attach two Spring Clips (#39) onto the Weight Bar. DIAGRAM 6 9
ملخص المحتوى في الصفحة رقم 11
10
ملخص المحتوى في الصفحة رقم 12
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Rear Upright Beam 2 2 Cross Brace 1 3 Main Seat Support 1 4 Diagonal Support 1 5 Front Support 1 6 Leg Developer 1 7 Backrest Support 2 8 Backrest Board 1 9 Seat 1 10 Bracket 3 11 Backrest Adjustment Bar 1 12 Foam Roll 4 13 Foam Tube 2 14 Ø ¾” Round End Cap 4 15 Ø 1” Round End Cap 7 16 Rubber Bumper 1 17 1 ½” Square End Cap 2 18 M8 x 2 3/8” Hex Bolt 4 19 1” Square End Cap 4 20 M8 x 2 ½”Hex Bolt
ملخص المحتوى في الصفحة رقم 13
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Cus
